BOAT ROCKERZ 510 (01) PDF Document

To maintain the continuous stability of the signal, please try to keep the Bluetooth and mobile phone in the same direction.

When pairing the headset with a Bluetooth mobile phone, the dedicated linking route will be created for these two Bluetooth devices only. As per the Bluetooth technology used for the headset, it is not easy for third parties to monitor the conversations, and the RF power of the Bluetooth wireless signal is far less than that of a normal mobile phone, so these signals are difficult to be detected by third parties.

When the distance between the mobile phone and Bluetooth headset exceeds the effective distance, the connection between the mobile phone and Bluetooth headset will be broken automatically. When it comes back into the effective distance, the mobile phone and Bluetooth headset will be connected automatically without any setting. However, some phones do not support this function; for these, the Bluetooth device should be searched in the design list and then connected.

A) Insert the charger plug in the headset, and put the release label side of the charger down, and put the headset right side up.

B) Insert the other end of the charger into a power outlet. When charging, the headset indicator is on until the end of charging. The first charging takes about eight hours, and about three hours afterwards.

C) When charging is completed (indicator is off), remove the charger from the power outlet, and press the release button on the charger plug, and remove the charger from the headset.

Note: When you are driving a vehicle, charge the Bluetooth headset with the original vehicle power charger.

1. To avoid damage to your ears, please limit the time using the headset at high volumes, and set the volume at a safe level. The higher the volume, the shorter the safe listening time.

2. If you are in a potentially hazardous site, please stop using the headset to prevent damage or malfunction.

3. Please do not expose the headset to high temperature in places such as near heating facilities or in the car exposed to direct sunlight.

4. Please do not immerse the headset in water.

5. Please do not use any alcoholic ammonia for cleaning. If necessary, please use a soft cloth to clean it.

6. Do not store the headset where the temperature is below -15 degrees or above 35 degrees. The battery life may be shortened at low temperatures.

7. Please use the specified USB charging device. (Charging voltage DC4.7V-6V).

Power on: Long press the power button (about 3 seconds), and after the “beep” tone, Bluetooth is power on.

Pairing: When power is off, long press the power on button (about 3 seconds) and boot, and do not release the button, and continue to press the power button until “beep” tone. During Bluetooth pairing, red and blue lights alternately flash; set search, and when the manual connection is successful, blue light is on for long. Short press phone button once to enjoy the wonderful music.

Power off: When power on, long press the power on button (about 3 seconds), and after the “Beep” tone, power off process is initiated, red light is on till power off; red light is off.

Play/Pause: When playing music, short press the pause button to pause music, and short press again to restore music.

Increase Volume: Press “+” button to increase the volume (there will be a “beep” tone).

Reduce Volume: Press “-” button to reduce the volume.

Previous Music: Press “|<<” button to switch to previous music.

Next Music: Press “>>|” button to switch to next music.

When Line In inserting is detected, switch to Line In mode, disconnect Bluetooth and all indicator lights are off. When you pull out Line In, reboot and connect to Bluetooth automatically.

Yes. Low voltage alarming occurs when the voltage is under 3.3V; it makes a “beep” alarm tone. Insert the DC power source and it works normally. Under voltage automatic power off occurs when the voltage is under 3.3V; Bluetooth automatically turns off the device. After re-charging, press the power button to reboot.

When receiving a call, the music automatically disconnects, and the Bluetooth headset switches to the phone function.

To end the call, short press the multifunction button, and music automatically connects.

When the caller ends the call, music automatically connects without any action.

When playing music, short press the phone button twice to redial the last incoming call or outgoing call.

1. If the computer does not come with Bluetooth capabilities, please purchase an additional Bluetooth adapter.

2. Insert the Bluetooth adaptor in the USB interface of the computer, install Bluetooth adapter driver according to the computer tips, and the specific steps are as follows:

A) Open the control panel and select the “Sounds and Audio Devices”.

B) Select the “Audio” tab, and select the installed Bluetooth sound device in the “Playback Device” and “Recording Device, and select OK after setting and then exit.

C) Then select the “Voice” tab, and select the installed Bluetooth sound device in the “Playback Device”, and select OK after setting and then exit.

3. Turn on the Bluetooth headset (long press the power on button on the headset until the Bluetooth indicator flashes once every few seconds regularly, it indicates that the headset is in the process of power on).

4. Open the Bluetooth management software, and press the function button on the Bluetooth headset for about ten seconds. When the two-colour indicator light flashes alternately every few seconds, it indicates that the Bluetooth headset is in pairing state. Only in this case is the Bluetooth adapter likely to search for the Bluetooth headset.

5. Click “My Bluetooth” and select “Search for Bluetooth Devices” to search the surrounding Bluetooth devices such as the Bluetooth headset.

6. If there are Bluetooth devices nearby, then the searched devices will be listed.

7. Right-click on the searched device and then select “pair”.

8. Enter “0000” as the pairing code in the dialog box.

9. If the computer comes with a Bluetooth adapter, and the drivers and software are installed, first start searching. If the Bluetooth headset is searched, connect directly and try the Bluetooth headset; if there is sound, then setting is successful.

A) Confirm if Bluetooth headset is power on or off (if power on, blue and red indicator light flash alternately).

B) If it is power on and still can’t search, please reboot Bluetooth and mobile phone.

A) Bluetooth power is low, you need to charge the Bluetooth headset as soon as possible.

B) There is obstruction between the phone and the Bluetooth or the distance exceeds the signal reception distance. Please do not place your hands between your device and Bluetooth headset.