LG 60LB561V-ZC (01) PDF Document

To attach the stand to your LG 60LB561V-ZC, place the screen facing down on a cushioned table or flat surface to protect it from scratches. Then, follow the assembly instructions provided in the diagrams in your owner’s manual. The specific screws required will vary based on your exact model number.

Connect your LG 60LB561V-ZC TV to a wall antenna socket using an RF cable (75 Ω).

Important Notes:

• If you need to use more than 2 TVs, use a signal splitter.

• If the image quality is poor, you may need to install a signal amplifier.

• If image quality is poor with an antenna connected, try to realign the antenna to point it in the correct direction.

• An antenna cable and converter are not supplied with the TV.

• Supported DTV Audio formats are MPEG, Dolby Digital, Dolby Digital Plus, and HE-AAC.

To connect a satellite dish to your LG 60LB561V-ZC (on satellite models only), connect the TV to the satellite dish’s satellite socket using a satellite RF cable (75 Ω).

The Euro Scart connection transmits video and audio signals from an external device to the TV. The AV1 (TV Out) port outputs either Analogue TV or Digital TV signals depending on the current input mode.

Note: Any Euro scart cable used must be signal shielded.

When connecting various external devices like HD receivers, DVD players, VCRs, audio systems, USB storage devices, PCs, and gaming devices to your LG 60LB561V-ZC, please follow these guidelines:

• The external device connection may differ from the model.

• Connect external devices to the TV regardless of the order of the TV port.

• If you record a TV programme on a DVD recorder or VCR, ensure the TV signal input cable is connected to the TV through the DVD recorder or VCR.

• Refer to the external equipment’s manual for operating instructions.

• If you connect a gaming device, use the cable supplied with it.

• In PC mode, you may experience noise associated with resolution, vertical pattern, contrast, or brightness. If this occurs, change the PC output to another resolution, change the refresh rate, or adjust the brightness and contrast in the PICTURE menu until the picture is clear.

• In PC mode, some resolution settings may not work properly depending on the graphics card.

The Joystick button, located below the TV screen, allows you to operate basic TV functions by pressing or moving it up, down, left, or right.

Basic Functions:

• Power On: When the TV is off, press the joystick button once and release it.

• Power Off: When the TV is on, press and hold the joystick button for a few seconds and release it. (If the Menu is on screen, this action will exit the Menu).

• Volume Control: Move the joystick left or right to adjust the volume.

• Programmes Control: Move the joystick up or down to scroll through saved programmes.

Adjusting the Menu:

When the TV is on, press the joystick button once to bring up the menu. You can then adjust the menu items by moving the joystick.

Note: When moving the joystick, be careful not to press it first, as this will prevent you from adjusting the volume or scrolling through programmes.

To prevent scratches or damage and ensure safe transportation, please follow this advice when lifting and moving your LG 60LB561V-ZC:

• Avoid touching the screen at all times, as this may result in damage.

• It is recommended to move the TV in the box or packing material it originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Do not hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV, do not expose it to jolts or excessive vibration.

• Keep the TV upright during transport; never turn it on its side or tilt it left or right.

• Do not apply excessive pressure that could cause the frame chassis to flex or bend, as this may damage the screen.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum space of 10 cm from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Caution: Do not place the TV near or on sources of heat, as this may result in fire or other damage.

This feature is not available for all models. If your model supports it, follow these steps:

1. Insert and tighten the eye-bolts (or TV brackets and bolts) on the back of the TV. If there are already bolts in the eye-bolt position, remove them first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Caution: Make sure that children do not climb on or hang on the TV.

Note: Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts, and ropes are not provided.

LG recommends that wall mounting be performed by a qualified professional installer. Ensure you use screws and a wall mount bracket that meet the VESA standard.

Cautions:

• Disconnect the power first before moving or installing the TV to avoid electric shock.

• If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount.

• Do not over-tighten the screws, as this may cause damage to the TV and void your warranty.

• Use screws and wall mounts that meet the VESA standard. Any damages or injuries from misuse or improper accessories are not covered by the warranty.

The standard dimensions and screw types for the LG 60LB561V-ZC are as follows:

The remote control for your LG 60LB561V-ZC has the following functions:

Note: To replace batteries (1.5 V AAA), open the battery cover, match the + and – ends, and close the cover. Do not mix old and new batteries.

To automatically tune the programmes on your LG 60LB561V-ZC, go to SETTINGS → SETUP → Auto Tuning. This function automatically finds and registers programmes that are currently broadcasting. Note that if the Input Source is not connected properly, programme registration may not work. If the Lock System is turned on, a pop-up window will appear asking for the password.

To select a picture mode optimized for your viewing environment, go to SETTINGS → PICTURE → Picture Mode. The available modes are:

• Vivid: Heightens contrast, brightness and sharpness to display vivid images.

• Standard: Displays images in standard levels of contrast, brightness and sharpness.

• Eco/APS: The Energy Saver feature changes settings to reduce power consumption.

• Cinema/Game: Displays the optimum picture for movies or games.

• Sports: Optimizes the video image for high and dynamic actions by emphasizing primary colours such as white, grass, or sky blue.

• Expert 1, 2: Menu for adjusting picture quality that allows experts and amateurs to enjoy the best TV viewing. This is the adjustment menu provided for ISF-certified picture tuning professionals.

To calibrate the screen for each picture mode, go to SETTINGS → PICTURE → Picture Mode → Advanced Control / Expert Control. First select a Picture Mode, then you can adjust the following settings:

• Dynamic Contrast: Adjusts contrast to the optimal level according to image brightness.

• Dynamic Colour: Adjusts colours to make the image appear more natural.

• Skin Colour: Sets the skin colour spectrum separately.

• Sky Colour: Sky colour is set separately.

• Grass Colour: Natural colour spectrum (meadows, hills, etc.) can be separately set.

• Gamma: Sets the gradation curve according to the output of the picture signal.

• Colour Gamut: Selects the range of colours that can be expressed.

• Edge Enhancer: Shows clearer and distinctive yet natural edges of the video.

• Colour Filter: Filters a specific colour spectrum in RGB colours to fine-tune colour saturation and hue.

• Colour Temperature: Adjusts the overall tone of the screen as desired.

• Colour Management System: A system for experts to adjust colour with a test pattern, selecting from six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow) without affecting other colours.

To access detailed settings for images, go to SETTINGS → PICTURE → Picture Mode → Picture Option. The options include:

• Noise Reduction: Eliminates noise in the picture.

• MPEG Noise Reduction: Eliminates noise generated while creating digital picture signals.

• Black Level: Adjusts the brightness and contrast of the screen to suit the black level of the input picture.

• Real Cinema: Optimizes the screen for movie viewing.

• Motion Eye Care/SUPER Energy Saving: Saves power consumption by adjusting the brightness corresponding to the movement of the image on the screen.

The Energy Saving feature reduces power consumption by adjusting screen brightness. Access it via SETTINGS → PICTURE → Energy Saving.

• Auto: The TV sensor detects ambient lighting and automatically adjusts the screen brightness.

• Off: Turns off the Energy Saving mode.

• Minimum / Medium / Maximum: Applies the pre-set Energy Saving mode.

• Screen Off: The screen is turned off and only sound is played. Press any button (except the Power button) on the remote control to turn the screen back on.

You can manage your TV’s audio output through the SETTINGS → AUDIO → Sound Out menu.

• TV Speaker: Sound is output through the TV’s internal speakers.

• External Speaker (Optical): Sound is output through a speaker connected to the optical port. SimpLink is supported.

• LG Sound Sync (Optical): Connect an LG audio device to the optical digital audio output port for rich, powerful sound.

• Headphone: Sound is output through the headphone port.

For the External Speaker (Optical) output, you can set up the Digital Sound Out format:

SIMPLINK is a feature that enables you to control and manage various multimedia devices conveniently via the TV remote control and the SIMPLINK menu. It only works with devices that have the SIMPLINK logo.

To set up SIMPLINK:

1. Connect the TV’s HDMI IN terminal to the SIMPLINK device’s HDMI output terminal using a high-speed HDMI® cable (with CEC feature).

2. Select INPUT(OPTION) → SIMPLINK. The SIMPLINK menu window will appear.

3. In the SIMPLINK Setting window, set the SIMPLINK function to ON.

4. In the SIMPLINK menu window, select the device you want to control.

SIMPLINK Functions:

• Direct Play: Plays the multimedia device on the TV instantly.

• Select multimedia device: Selects the desired device via the SIMPLINK menu to control it from the TV screen instantly.

• Disc playback: Manages the multimedia device with the TV remote control.

• Power off all devices: When you power off the TV, all connected devices are turned off.

• Sync Power on: When equipment with SIMPLINK connected to an HDMI terminal starts to play, the TV will automatically turn on.

• Speaker: Select the speaker on either the home theatre unit or the TV.

To set or change the TV password, go to SETTINGS → LOCK → Set Password. The initial password is set to ‘0000’.

To reset your TV to its factory settings, go to SETTINGS → OPTION → Factory Reset. This will delete all stored information and reset all TV settings. The TV will turn itself off and back on to complete the process. Do not turn off the power during initialization. If the Lock System is active, a pop-up window will appear and ask for the password.

When using a USB storage device, please be aware of the following:

• If the USB device has a built-in auto recognition program or uses its own driver, it may not work.

• Some USB devices may not work or may work incorrectly.

• Use only USB storage devices formatted with the Windows FAT32 or NTFS File System.

• For external USB HDDs, it is recommended to use devices with a rated voltage of less than 5 V and a rated current of less than 500 mA.

• It is recommended to use USB memory sticks of 32 GB or less and USB HDDs of 1 TB or less.

• If a USB HDD with a power-saving function does not work properly, turn the power off and on.

• Data in the USB storage device can be damaged, so be sure to back up important files. Data maintenance is the user’s responsibility.

To remove a USB device, select it in Q.MENU → USB Device. When you see the message that the device has been removed, you can safely separate it from the TV.

To keep your TV in the best condition, clean it regularly. First, make sure to turn the power off and disconnect the power cord and all other cables.

Screen, frame, cabinet and stand:

• To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

• To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.

Cautions:

• Avoid touching the screen at all times, as this may result in damage.

• Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches and image distortions.

• Do not use any chemicals as this may damage the product.

• Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.

Power cord:

Remove the accumulated dust or dirt on the power cord regularly.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote control.

• Check if the batteries are still working and properly installed (match the + and – terminals).

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

• Check the power control settings. The power supply may be interrupted.

• Check if the Automatic Standby, Sleep Timer, or Off Time feature is activated in the TIME settings.

• If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

• Turn the TV off and on again using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.