LG 50UN6951ZUF (02) PDF Document

Install your LG 50UN6951ZUF where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not install the product on a carpet or cushion. Do not block or cover the product with cloth or other materials while the unit is plugged in. Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

Do not defeat the safety purpose of the polarized or grounding-type plug. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not move the TV whilst the power cord is plugged in. Do not use a damaged or loosely fitting power cord. Be sure to grasp the plug when unplugging the power cord; do not pull on the power cord to unplug the TV. Unplug the apparatus during lightning storms or when unused for long periods of time.

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

1. Lift and tilt the TV into its upright position on a table. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

2. Connect the power cord to a wall outlet.

Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. If you install the TV on a stand, you need to take actions to prevent the product from overturning.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts, and ropes are not provided.

Make sure to use screws and wall mount bracket that meet the VESA standard.

Connect an antenna, cable, or cable box to watch TV while referring to the illustrations provided in the manual. Make sure not to bend the copper wire of the RF cable. Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV. Use a signal splitter to use 2 TVs or more.

When connecting the HDMI cable, the product and external devices should be turned off and unplugged. Supported HDMI Audio Formats include True HD (48 kHz), Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz), and PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz).

For best picture quality, go to [Picture] -> [Additional Settings] -> [HDMI Ultra HD Deep Color]. If the device connected to the Input Port supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off.

Use a certified cable with the HDMI logo attached. Recommended HDMI cable types are Ultra High Speed HDMI cable (3 m or less).

You can operate the TV functions using the button located on the TV:

Power On: Press the button.

Power Off: Press and Hold the button.

Menu Control: Press the button once while the TV is on to access the menu.

Menu Selection: Press and Hold the button to select an option.

When the TV is turned on and you press the button one time, you can adjust the Menu items (Turn the power off, Change the input source, Adjust the volume level, Scroll through the saved channels) using the button.

To use the Magic Remote, first pair it with your TV:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV. Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

Check if anything such as tape has been placed over the receiver. Check if there is any obstacle between the product and the remote control. Replace the batteries with new fresh ones.

Check the power control settings. The power supply may be interrupted. Check if the auto-off function is activated in the settings menu. If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Make sure to wring any excess water or cleaner from the cloth. Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

The following table lists the commands for external control device setup:

* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. With RS232C cable, TV can communicate “ka command” in power-on or power-off status. but with USB-to-Serial converter cable, the command works only if TV is on.

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General -> About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.