LG 43UN7300AUD (02) PDF Document

When cleaning the LG 43UN7300AUD, ensure you unplug the power cord and wipe gently with a soft, dry cloth. Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Failure to follow these instructions may result in electric shock or product damage.

Make sure to wring any excess water or cleaner from the cloth before wiping. Do not spray water or cleaner directly onto the TV screen; spray just enough of water or cleaner onto a dry cloth to wipe the screen.

When moving or lifting the LG 43UN7300AUD, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product.

If you install the TV on a stand, you need to take actions to prevent the product from overturning.

Do not use any unapproved items to ensure the safety and product life span.

Make sure that the screws are fastened tightly. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not fasten the screws with excessive force otherwise they may strip and become loose.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table:

Connect an antenna, cable, or cable box to the TV while referring to the illustrations in the manual. Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

Navigate to [Picture] -> [Additional Settings] -> [HDMI Ultra HD Deep Color].

If the device connected to Input Port also supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off.

On: Support 4K @ 50 / 60 Hz (4:4:4, 4:2:2, 4:2:0)

Off: Support 4K @ 50 / 60 Hz (4:2:0)

You can operate the TV functions using the button located on the TV.

Power On: Press the button.

Power Off: Press and hold the button (All running apps will close).

Menu Control: Press the button while the TV is on.

Menu Selection: Press and hold the button. You can use this function when you access menu control.

When the TV is turned on, press the button one time. You can adjust the Menu items using the button to Turn the power off, Change the input source, Adjust the volume level, or Scroll through the saved channels.

To use the Magic Remote, first pair it with your TV.

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

Check the power control settings. The power supply may be interrupted.

Check if the auto-off function is activated in the settings menu.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

For more information about this TV, read the USER GUIDE embedded in the product. To open the USER GUIDE, select the [Settings] icon -> [Support] -> [User Guide].

Supported external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.

When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

For USB to Serial(RS-232C) converter with USB Cable: Connect the USB end to the USB IN port on the TV.

For RS-232C(Serial) With RS-232C(Serial) Cable (DE9 Type): Connect the DE9 cable to the RS-232C IN (CONTROL & SERVICE) port on the TV.

For Phone jack Type: Connect the phone-jack to RS-232 cable to the RS-232C IN (CONTROL & SERVICE) port on the TV.