LG 43UK6200PUA (01) PDF Document

To ensure safe operation of your LG 43UK6200PUA TV, please follow these instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug.

• Protect the power cord from being walked on or pinched.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel.

To prevent fire, electric shock, or product damage, do not place the LG 43UK6200PUA TV or its remote control in the following environments:

• Keep the product away from direct sunlight.

• An area with high humidity, such as a bathroom.

• Near any heat source, such as stoves and other devices that produce heat.

• Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

• An area exposed to rain or wind.

• Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases or cups, on or over the apparatus.

• Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

• Do not install in excessively dusty places.

To prevent the spread of fire, keep candles or other items with open flames away from this product at all times.

• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

• The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

• Make sure the power cord is connected securely to the TV and wall socket. If not secured, damage to the Plug and socket may occur, and in extreme cases, a fire may break out.

When cleaning your LG 43UK6200PUA, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol, etc., which can damage the product and/or its panel. This may result in electric shock or product damage.

For an optimal connection with your LG 43UK6200PUA, HDMI cables and USB devices should have bezels with the following dimensions:

• Thickness (A): 10 mm (0.39 inches) or less

• Width (B): 18 mm (0.7 inches) or less

If a USB cable or USB flash drive does not fit into your TV’s USB port, use an extension cable that supports USB 2.0.

The specifications for wall mounting your LG 43UK6200PUA TV are as follows. Please ensure you use screws and a wall mount bracket that meet the VESA standard.

When moving or lifting the TV, please follow these recommendations to prevent scratching or damage and ensure safe transportation:

• It is recommended to move the TV in the box or packing material that it originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

• Use at least two people to move a large TV.

• When transporting the TV by hand, hold the TV as shown in the illustrations in the manual.

• Do not expose the TV to jolts or excessive vibration.

• Keep the TV upright; never turn the TV on its side or tilt it towards the left or right.

• Avoid touching the screen at all times, as this may result in damage to the screen.

1. Lift and tilt the TV into its upright position on a table.

2. Ensure there is a minimum of 10 cm (4 inches) of space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Note: When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

To prevent the TV from tipping over, you can secure it to a wall. Brackets, bolts, and ropes are not provided but can be obtained from your local dealer.

1. Insert and tighten the eye-bolts, or TV brackets and bolts, on the back of the TV. If there are already bolts in the eye-bolt position, remove them first.

2. Mount the wall brackets with the bolts to the wall. The location of the wall bracket should match the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Ensure you use a platform or cabinet that is strong and large enough to support the TV securely.

You can operate basic TV functions using the button on the unit.

Basic Functions:

• Power On: Press the button.

• Power Off: Press and hold the button.

• Menu Control: Press the button when the TV is on to access the menu.

• Menu Selection: Press and hold the button to select a menu item.

Adjusting the Menu:

When the TV is on, press the button once to bring up the menu. You can then press the button repeatedly to cycle through and adjust the menu items:

• Turns the power off.

• Changes the input source.

• Scrolls through the saved channels.

• Adjusts the volume level.

How to register the Magic Remote Control:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the BACK and HOME buttons at the same time for five seconds to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button will let you cancel and re-register the Magic Remote at the same time.

• Check if anything, such as tape, has been placed over the receiver on the TV.

• Check if there is any obstacle between the TV and the remote control.

• Replace the batteries with new fresh ones.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products to it.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated in the settings menu.

• If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

• Flicker: If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal and there is nothing wrong with the TV.

• Dot Defects: Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. This panel is an advanced product that contains millions of pixels, and in a very few cases, you could see fine dots on the screen. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

• Image Sticking: Displaying a still image for a prolonged period may cause image sticking. Avoid displaying a fixed image on the TV screen for an extended length of time.

• Cracking noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

• Electrical circuit humming/panel buzzing: A low-level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

The specifications for the wireless module (LGSWFAC71) in your LG 43UK6200PUA are as follows:

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body.

You can connect an external control device like a computer to the USB to Serial converter/RS-232C input jack to control the TV’s functions externally. Please note that cables are not provided.

USB to Serial converter with USB Cable:

Your LG TV supports a PL2303 chip-based (Vendor ID: 0x0557, Product ID: 0x2008) USB to serial converter. This can be purchased from computer stores.

RS-232C with RS232C Cable (D-Sub 9pin Type):

You need to purchase an RS-232C (DE9, D-Sub 9pin female-to-female type) cable for the connection between the PC and the TV.

Phone Jack Type:

You may need to purchase a phone-jack to RS-232 cable. For other models, connect to the USB port. The connection interface may differ from your TV.

• Baud rate: 9600 bps (UART)

• Data length: 8 bits

• Parity: None

• Stop bit: 1 bit

• Communication code: ASCII code

• Use a crossed (reverse) cable.

Transmission Protocol:

[Command1][Command2][ ][Set ID][ ][Data][Cr]

• [Command 1]: First command to control the TV (j, k, m or x).

• [Command 2]: Second command to control the TV.

• [Set ID]: You can adjust the [Set ID] to choose the desired monitor ID number (1 to 99). If ‘0’ is selected, every connected set can be controlled. [Set ID] is indicated as decimal (1-99) on the menu and as Hexadecimal (0x00 to 0x63) in the protocol.

• [DATA]: To transmit command data (hexadecimal). Transmit ‘FF’ to read the status of a command.

• [Cr]: Carriage Return – ASCII code ‘0x0D’.

• [ ]: Space – ASCII code ‘0x20’.

OK Acknowledgement:

[Command2][ ][Set ID][ ][OK][Data][x]

The TV transmits this acknowledgement (ACK) when receiving normal data. If the data is in read mode, it indicates the present status. If in write mode, it returns the data from the PC.

Error Acknowledgement:

[Command2][ ][Set ID][ ][NG][Data][x]

The TV transmits this when receiving abnormal data, from non-viable functions, or in case of communication errors. Data 00 indicates an Illegal Code.