LENOVO L24I-4B (01) PDF Document

To set up the stand, perform the following steps:

1. Place your LENOVO L24I-4B with the screen face down on a soft flat surface.

2. Insert the base towards the stand until it locks in place.

3. Insert the base towards the stand and tighten the thumbscrew.

To connect and power on the LENOVO L24I-4B, follow these steps:

1. Power off your computer and all attached devices, and unplug the computer power cord.

2. Connect the cables according to the icon indications on the monitor.

3. Connect one end of the HDMI cable to the HDMI connector on the back of the computer, and the other end to the HDMI connector on the LENOVO L24I-4B.

4. Connect the audio cable of the sound box to the audio jack of the LENOVO L24I-4B to transmit audio sources from HDMI.

5. Connect one end of the analog signal cable to the monitor VGA connector and the other end to the computer.

6. Plug the monitor power cord and the computer cord into grounded electrical outlets.

7. Connect the cables with the cable clip.

8. Power on the LENOVO L24I-4B and the computer.

To adjust the settings on your LENOVO L24I-4B, use the following controls:

1. Press the menu button to open the main OSD menu.

2. Use the navigation buttons to move among the icons. Select an icon and press the enter button to access the selected function. If there is a sub-menu, you can move between options using the navigation buttons, then press the enter button to select that function. Use the navigation buttons to make adjustments, then press the enter button to save.

3. Press the back button to move backwards through the sub-menus and exit from the OSD.

The OSD functions for the LENOVO L24I-4B are organized as follows:

Basic Settings: Includes adjustments for Brightness, Contrast, DCR (On/Off), Display Mode (Standard, Game, Movie, Web, Picture), Scaling Mode (Full Screen, Original AR), Auto Adjust (Automatic, Clock, Phase, Horizontal Position, Vertical Position), Over Drive (Off, Normal, Extreme), MPRT (On, Off), and Video Range (Auto, Full Range 0-255, Limited Range 16-235).

Color Settings: Includes sRGB, Neutral, Warm, Cool, and Custom (Red, Green, Blue).

Audio Settings: Includes Volume and Mute (On/Off).

Port Settings: Includes Input Signal (Auto Switch Input, VGA, HDMI).

Menu Settings: Includes Information (Model Name, Refresh Rate, Firmware, Serial Number), Language, Menu Position, Transparency, OSD Timeout, LED Indicator (On/Off), Button Repeat Rate (Default, Slow, Off), DDC/CI (On/Off), and Factory Reset (Reset, No).

To manually install the monitor driver for your LENOVO L24I-4B in Windows, follow these steps:

1. Turn off the computer and all attached devices.

2. Ensure that the LENOVO L24I-4B is connected correctly.

3. Turn on the monitor and then the system unit. Start the Windows operating system.

4. Download the monitor driver for your LENOVO L24I-4B to your computer.

5. Right-click the Windows Start button, then click Device Manager, and double-click Monitor.

6. Double-click Generic Monitor.

7. Click the Driver tab.

8. Click Update Driver, and then click Browse Computer to find the driver.

9. Click Let me pick from a list of available drivers on my computer.

10. Click the Have Disk button. Browse to the folder where the downloaded driver is located.

11. Select the l24i-4b.inf file, click Open, then click OK.

12. Select L24I-4B and click Next.

13. After the installation is complete, close all windows.

14. Restart the system.

Follow these maintenance guidelines for your LENOVO L24I-4B:

Do not apply water or liquid directly to your LENOVO L24I-4B. Do not use solvents or abrasives, or flammable cleaning materials. Do not touch the screen area with sharp or abrasive items.

Do lightly dampen a soft cloth with water and use this to gently wipe the covers and the screen. Remove grease or finger marks with a damp cloth and a little mild detergent.

To convert your LENOVO L24I-4B to a wall-mounted display, do the following:

1. Verify that the power button is turned off, and then disconnect the power cord.

2. Lay the LENOVO L24I-4B face down on a towel or blanket.

3. Remove the base from the monitor.

4. Attach the mounting bracket from the VESA compatible wall mounting kit (100mm x 100mm distance), using VESA Mounting Screw M4 x 10 mm.

5. Attach the LENOVO L24I-4B to the wall following the instructions in the wall-mounting kit.

If the LENOVO L24I-4B displays “Input Not Supported” and the power indicator is flashing white, the system is set to a display mode which is not supported by the monitor. Try the following:

If you are replacing an old monitor, reconnect it and adjust the display mode to within the specified range for your new LENOVO L24I-4B. If using a Windows system, restart the system in safe mode, then select a supported display mode for your computer.

If the image quality on your LENOVO L24I-4B is unacceptable, ensure the signal cable is firmly plugged into the system and monitor. You may also select another color setting from the OSD menu to improve the image.

If the power indicator on your LENOVO L24I-4B is not lit and there is no image, check the following:

Ensure the power cord is connected properly to the LENOVO L24I-4B and the electrical outlet. Ensure the outlet has power. Power on the monitor. Try using another power cord or another electrical outlet.

If the LENOVO L24I-4B screen is blank and the indicator is steady amber or flashing white, the monitor is in Standby/Suspend mode. Press any key on the keyboard or move the mouse to restore operation, or check the power options settings on your computer.