KUSSMAUL LPC 20 091-207-12 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL LPC 20 091-207-12 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL- I-PC eo LOW PROFILE CHARGER AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays AUTO A.urownwczsrarusctrrt# auro CHARGE* MODEL # : 091-207-12 INpu-r: 120 Volt, 50/60 Hz, 7 Amps File: IM_OBI -207-12_revA1 .jndd Revised By: PSS, pg e Date: 4-16-201 a 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com OUTPUT: 20 Amps a YEAR WARRANTY KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS couNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** IMPORTANT SAFETY INs-rnucT/0Ns l. PERSONAL PRECAUTIONS: 1. 2. 3. 4. 5. 6. 7. 8. 9. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. Wear complete eye and clothing protection. Avoid touching your eyes while working near a battery. If battery acid contacts skin or clothing, wash immediately with soap and water. If battery acid enters the eye, immediately flood eye with cold running water for at least 10 minutes and get medical attention immediately. NEVER smoke or allow a spark or flame in the vicinity of the battery or engine. Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit the battery or other electrical part and cause a fire or an explosion. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery, when shorted, can produce a current sufficient to weld a ring or the like metal causing a severe burn. Use the battery charger for charging gel-cell, AGM and flooded lead-acid batteries only. Do not use the charaer for charging dry-cell batteries that are commonly used with home applications. These batteries may burst and cause inu to WARNING RISK OF to Pr0PertY. Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. II. CHARGER PRECAUTIONS: 1. 2. 3. 4. 5. 6. 7. 8. NEVER charge a frozen battery. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Do not operate the charger with a damaged cord or plug; replace them immediately. Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged. Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock and fire. To reduce the risk of electric shock, disconnect the charger from the AC source before attempting any maintenance or cleanin LOCATION OF CHAR8ÉR The charger should be mounted on a wall, vehicle floor, ventilated compart- ment or other suitable surface as close to the batteries to be charged as possible. Do not block the char- ger’s fan or air intakes. Do not mount the charger directly over the batteries as fumes may cause exces- Sive corrosion. The area should be well ventilated and free from excessive moisture, exhaust manifolds, and battery fumes. For maximum performance, the charger should not be located in an area of extreme high temperature. The charger is not waterproof. Do not mount the charger where there is a possibility of water entering the unit. Evidence of water entry into the charger will void the warranty. CAUTION: Do not attempt to increase battery bank capacity by splitting the output of one of the banks with a diode-type battery isolator. The diode isolator lowers the charger voltage and results in under- charging the batteries connected to it. If additional capacity is required it is preferable to add another isolated or parallel battery. Ill. GROUND AND AC POWER CORD CONNECTION 1. 2. 3. 4. The charger should be grounded via the AC power connection to reduce the risk of electrical shock. The charger must be plugged into or wired to an outlet that is an over-current protected 3 prong outlet. Alternatively, it may be routed through a separate dedicated fuse or circuit breaker on an AC distribution panel with proper earth/safety ground. All wiring shall comply with UL recommendations, NEC or NFPA standards and local ordinances. Never alter the AC cord or lug if provided. Any modification of the cord must only be done by a qualified electrician. Improper cord outlet connection may result in a risk of elec- trical shock. Observe color coding of the AC wiring as follows: Black. AC Hot or LINE (fused) White… AC Neutral . AC Ground (safety/earth) CAUTION: 230 VAC applications only): If AC input is provide from a source consisting of two HOT or LINE leads phase-to-phase 230 VAC input voltage); an external fuse or circuit breaker must be used to protect both hot leads. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 3 ****** INTRODUCTION The LPC 20 is a low profile, completely automatic, single channel battery float charger designed for vehicles with a single battery system. The LPC 20 improves upon package size and parasitic systems. The charger is also ruggedized to withstand the shock and vibration encountered by vehicle mounted equipment. FEATURES l. LPC 20 BATTERY CHARGER • Automatic current limiting • Remote Battery charge/condition indicator display • LED status indicators • AUX output with AC or DC mode rocker switch and automatic fuse protection • Reverse polarity protected • Dual AC input fuse protection II. CHARGE CONTROLS & ELECTRONIC REMOTE SENSING The LPC 20 contains a precision voltage controller to maintain the battery’s charge. Using high- frequency switching technology the output terminal voltage is compared to a reference voltage, any error detected is then used to control the charger output at the desired level. There is no “trickle charge” and therefore no danger of overcharging and water boil-off. Ill. AUTOMATIC CURRENT LIMITING When batteries are severely discharged, some battery chargers can be overloaded due to the high charging current required. The LPC 20 contains an automatic current limit. The current limit feature limits the output current to 20 amperes when charging a deeply discharged battery, or if the starter cranks the engine while charging. The current limiter thus eliminates the need for an ignition interlock circuit. IV. BATTERY SELECTOR SWITCH (LEAD-ACID/AGM OR GEL-CELL) Not applicable with this model. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 3

****** Page 4 ****** V. AUX OUTPUT The output terminal strip provides an additional output to accomodate 12 volt accessories, such as: Kussmaul’s 12Vdc air pump. The AUX output works in conjunction with a front panel mounted rocker switch. For normal operation, the rocker switch should be left in AC mode, which means that the aux accessory works only when shoreline power is supplied to the charger. With the switch in DC mode the aux accessory will operate when AC power is ON or OFF. In either position the aux output operates from the vehicle’s batteries, while the charger automatically recharges the batteries as required. VI. AUX OUTPUT AUTOMATIC RESET FUSE The LPC 20 contains an internal automatic reset fuse. fuse by cycling the AC input power (shore line). VII. LED STATUS INDICATORS Should the AUX output fuse open, reset the 1. AUX ON: Indicates that power to the AUX output terminal is ON. 2. AC ON: Indicates that AC input voltage is present. Note: Battery must be above 9Vdc and of proper polarity. 3. BATTERY 0K: Indicates a battery of proper polarity is connected to the charger output terminals. VIII. COOLING FAN The LPC 20 is fan cooled and automatically cycles on and off depending on the output load current. Air is circulated from the rear panel and exhusted through the front panel. OPERATION l. BATTERY CHARGER OUTPUT 1. A discharged battery is recharged to roughly 90% or until the current tapers down to less than 2 amps. The ouput voltage never exceeds the float voltage, which is regulated from 0 to 20 amps (current-limit). 2. The charger will continue to charge the battery until the voltage at the battery reaches float voltage level. II. AUX OUTPUT 1. 2. The AUX output is current-limited to 15 amps via an internal automatic reset fuse. The AUX output shares current demand with the battery output. The combination of both outputs never exceeds 20 amps. If the AUX output demands 15 amps then the battery output will be limited to 5 amps. The AUX output voltage follows the battery output voltage. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 4

****** Page 5 ****** WIRING l. BATTERY CHARGER WIRING INSTRUCTIONS 1. 2. 3. 4. 5. Refer to Installation Wiring Diagram l. and II. Refer to Wiring Specifications to determine the recommended wire size and maximum lengths. Using a smaller gauge may cause overheating of the terminal. Additional information is available upon request if longer, larger wiring is required. Double check all wiring before applying AC power to input terminal. Apply AC power (shoreline power) to input terminal and observe that the charger is operating. Verify that the battery voltage appears at the charger output terminals. A minimum of 9 volts is required to start the charger. II. WIRING SPECIFICATIONS Length of Wire to Battery (feet) Battery Charger Connections Wire # Gauge (awg) Wire Ferrule Used 10 12 10 10 5- 10 12 10 10 10 – 12 o 10 * Consult factory if length of wire to battery is longer than 20 feet ** Supplied with wire terminal hardware for 10 foot installation 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 6 ****** INSTALLATION WIRING DIAGRAM l. FOR BAR GRAPH DISPLAY, 091-200-IND OR DELUXE STATUS CENTER, 091-194B-lND Wiring Diagram shown is for a 10 foot installation Switch ruszsx.z opp o I o 0000000 000000 O BAT* AUX+ COM O O OOO 000000 00000 000000 ilil#” 000000 00000 000000 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 7 ****** II. FOR WATERTIGHT DELUXE STATUS CENTER, 091-194B-lND-WT-XX Wiring Diagram shown is for a 10 foot installation Swig 1>13 NotAppiicabio *CAPL.it opp o I o 0000000 000000 C) BAT+ AU*+ O O OOO oooooo ooooo oooooo AC LIL ratnmrrer•tlatnns, ræ.C, r.T fitanttrtrtfi oooooo ooooo oooooo 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT 12 Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 7

****** Page 8 ****** SPECIFICATIONS Input Power: 90-130 Volts, 50/60 Hz, 7 Amperes Input Fuse: (2) – 8 amp, fast acting, 5X20mm AUX Fuse: 15 Ampere, resettable, circuit breaker Output Power: 12 Volts DC, 40 Amperes Max Battery Selector Switch: Not Applicable Float Voltage: 13.25 volts (0 – 20 amps) Torque: DC output connector: 20 in. lbs LED Status Indicators: AUX On, Power On, and Battery 0K Hardware Pack Provided: (2) AWG Yellow Ferrules, PIN: 091-TERFEY1012 (1) AWG Gray Ferrule, PIN: 091-TERFEG1212 (1) 3-ft IEC cord Charger Indicators: Remote Bar Graph Display, Deluxe Status Center or Waterproof Status Center Output Waterproof Circuit Breaker (Optional): 30 Amperes, P/N: 090-0030-0 Output Buss Bar (Optional): 5 Studs, PIN: 002-3595-5 Weight: 7 pounds OUTLINE DRAWING 12.500 13.250 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com ooo 4.750 7.00 KUSSMAUL ELECTRONICS ENERGIZED READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 9 ****** OPTIONAL ACCESSORIES l. BAR GRAPH DISPLAY, MODEL 091-200-IND 10-Segment LED display indicate the “state of charge” and the general condition of the batteries II. DELUXE STATUS CENTER, MODEL 091-194B-lND Indicator has a digital voltage and ampere display 5 segment bar graph display indicates output current 4 LED’s to show the condition of the batteries Au-ro CHARGE’ AUTO CHARGE snus CENTER Ill. WATERTIGHT DELUXE STATUS CENTER, MODEL 091-194B-lND-WT-XX Indicator has digital voltage and ampere display • 5 segment bar graph display indicates output current 4 LED’s to show the condition of the batteries Indicator is housed in a watertight bezel Bezel is available in 6 different colors, Red, White, Blue, Yellow, Gray, and Black Specify color choice when ordering W. 30 AMP WATERPROOF CIRCUIT BREAKER, MODEL 090-0030-0 Combines switching and circuit breaker function Compact size and surface mount configuration Protects high amperage circuits Latch arms resets breaker after overload Cannot be held in ON position if short remains on circuit Waterproof – Ideal for truck applications V. E-Z SLIDE MOUNTING PLATE, MODEL 091-200-EZM • Locking mounting system Ease the installation and the removal of larger sized chargers that are in harder to access areas, such as under seats 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT CHARGE STATUS Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 10 ****** INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POI-ICY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kuss- maul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. Members of Fire and Einergency Manufacturers and Service Members of National fire Protection Association NFPA Members of Fire Apparatus Manufacturers Made in USA 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 10


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.