KUSSMAUL AUTO CHARGE 3 091-26-12 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL AUTO CHARGE 3 091-26-12 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** OBI -28-1 2, 4-28-97 INSTRUCTION MANUAL- A1-JT0 CHARGE 3 AUTOMATIC BATTERY CONDITIONER Conditioner Auto Charggg .1 —o Reedy Charge MODEL #091 -26-1 2 NOTE: THIS IS A coNDlT10NEA FOR MAINTAINING THE CHARGE IN A VEHICLE’S BATTERY. IT WILL RECHARGE THE BATTERY SLOWLY BUT IS NOT RECOM- MENDED FOR APPLICATIONS WITH AUXILIARY LOADS. INPUT: 1 20 VOLT, 50/60 Hz, 1 AMP MAX MAX. OUTPUT: 1 2 VOLTS, a AMPS a YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC. 1 70 CHERRY AVE. , WEST SAYVILLE, N.Y. 1 TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826

****** Page 2 ****** INTRODUCTION The Auto Charge 3Automatic Battery Charger is a compact, completely automaticcharger designed for installation on vehicles with two batteries. An internal charge divider charges both batteries simultaneously while maintaining complete battery isolation. A maximum output of 3 amperes privides sufficient current for vehicles which do not have large constant accessory loads. Indicator lights are provided to signal when the charger is charging and when the charging is complete. Construction of theAuto Charge 3 is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates completely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boiloff. Parasitic loads on the battery such as a radio, lights, etc., up to a maximum of 2 amps are automatically supplied with current from the charger.

****** Page 3 ****** INSTALLATION WIRING DIAGRAM Auto Charge@3 DUAL CONDITIONER Auto Charg Rea dy Charge o Green Red D.C. Output Fuse to Batteries REMOTE OUTPUT FUSE O Ready o Charge aATTERlES pog COMI 1 2 Chassis Ground INPUT FUSE IA 1 20 VAC Input Power Line Fuse Chassis Ground WIRE SIZE CHART CONNECTION ITEM COM BATTERY DEFINITION NEGATIVE CHARGING LEAD FOR BATTERIES POSITIVE CHARGING LEAD FOR BATTERY # 1 POSITIVE CHARGING LEAD FOR BATTERY # 2 WIRE SIZE 14 AWG 14 AWG 14 AWG IMPORTANT: Wire size is for a maximum length of 40 feet. Ifwiring is to be longer, larger wiring is re- quired. Additional information is available on request. 1 2 COMMON BATTERY NO.I BATTERY NO.2

****** Page 4 ****** SPECIFICATIONS SPECIFICATIONS: Input: 120 Volts, 60Hz, 1 amp Output Volts: 13.25 volts nominal Output Current: 0-3 Amps D.C. output current determined by state of charge of batteries Charge Indicator: RED LED indicates charging current GREEN LED indicates fully charged Remote Charge Indicator Connector: permits locating Red/Green LED’s at remote loaction Weight: 6 lbs OUTLINE DRAWING

****** Page 5 ****** INSTALLATION e WARRANTY Date Installed Installed By Vehicle Identification Vehicle Owner WARRANTY All product of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and /or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.