JOYOR S10-S-Z (01) PDF MANUAL

The main parts include:

1. LCD display

2. Lever lock for handlebar height adjustment

3. Handlebar sleeve

4. Brake wire

5. Brake handle (hydraulic on S10-S-Z)

6. Throttle

7. Front suspension

8. Front light

9. Front mudguard

10. Front air tyre

11. Front disc brake (hydraulic on S10-S-Z)

12. Front motor (S10-S-Z)

13. Folding system

14. Rear light

15. Turning lights

16. Parking stand

17. Rear motor

18. Rear air tyre

19. Rear mudguard

20. Rear disc brake (hydraulic on S10-S-Z)

21. Rear suspension

The vibration value exposed to the hand-arm system is 2.5 m/s2.

Measurement uncertainty is 0.5 m/s2. The vibration can be altered due to the rough terrain where the scooter is circulated. However, this alteration will not depend on the scooter.

The A-weighted emission sound pressure level is 35 db (A).

The electric scooter does not have the possibility of remote control. From the driver’s position, the driver can operate all the drive components necessary for the operation of the machine: brake, display with accelerator, handlebar, light switch, bell.

The displacement of the electric scooter with driver on board can only be implemented if the driver is at his command post, is prepared and only if the speed of the electric scooter is greater than 0 km/h, being started mechanically by pushing the scooter forward and applying the electric throttle only afterwards.

Joyor electric scooter is designed for adults only. People under the age of 16 cannot use this vehicle. Children should not use the vehicle or play with it.

This appliance can be used by children aged from 16 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Cleaning and user maintenance shall not be made by children without supervision.

Please wear a safety helmet when riding the electric scooter.

It is mandatory to wear shoes at all times while operating the electric scooter.

Please practice on an open traffic-free space on gear level 1 before riding on the bicycle lane.

Please during the riding operations always keep both hands on the handlebar and both feet on the standing board. Please do not jump on the standing board.

Please refrain from attaching any loads to the handlebar to maintain vehicle stability.

Do not turn off the motor power while riding the scooter.

Always anticipate your trajectory and your speed while respecting the code of the road, the code of the sidewalks and the most vulnerable.

Notify your presence when approaching a pedestrian or cyclist when you are not seen or heard.

If you encounter someone or obstacles in front of you during the riding, please release the throttle first, and brake the left brake handle (rear brake) first and then the right brake handle (front brake) next to deceleration or stop braking.

Do not try to ride over a gap of more than 3 cm. This may cause injury to the rider or damage the vehicle.

When riding on the rough or bumpy road, please slow down the electric scooter or stop riding the vehicle.

A user must adjust the height of the handlebar tube according to their height to ensure a safe, stable and comfortable ride.

Do not ride Joyor electric scooter on slippery surfaces such as oil or ice.

Do not use Joyor electric scooter in the weather conditions with the temperature below -5.

Do not leave the product immersed in a water depth of more than 3 cm to avoid damage to the electrical parts of the vehicle.

Do not store the vehicle in a place with high humidity levels.

Avoid riding the Joyor electric scooter in adverse weather conditions like rain, snow or wind storm to prevent an accident. If riding in these conditions, never exceed the speed of 10 km/h.

If the electric scooter is not used for a period of longer than 30 days, regularly charge it at least every 30 days.

Please ensure the scooter is turned off while charging or when it is in a non-operational mode.

The charging port must be kept clean and dry at all times.

When charging, always ensure that somebody is supervising the charging site. If the charger temperature increases too much, stop the charging process.

Always only use the original charger that corresponds to your scooter’s model.

Please keep all plastic bags of the packaging of the product away from children to avoid suffocation.

When unfolding the vehicle, please press the folding system handle till it clicks and make sure that it is in place.

Take the time to learn the basics of operating the electric scooter to avoid serious accidents, especially in the first months of use.

Approach the seller to be referred to an appropriate training organization for proper usage guidance.

Always engage the parking device when the electric scooter is not in use to ensure stability and prevent unintended movements.

The brake may become hot during use. Do not touch it immediately after use.

The Joyor electric scooter is not intended for acrobatic use; use it as per its intended purpose.

Do not use accessories or additional items that are not approved by the manufacturer.

Keep small plastic coverings away from children to prevent suffocation.

Avoid using the scooter in high traffic areas or overcrowded spaces.

When walking, it is mandatory to cross using designated protected passages.

Intensive use of the scooter may result in damage to its components. To prevent or detect potential issues, it is recommended to conduct periodic inspections on key parts such as the frame, fork, and suspension accessories.

Ensure to periodically check and retighten self-tightening nuts and other fastenings, as they may lose efficiency over time.

Regularly check for and eliminate any sharp edges caused by the use of the scooter.

Do not modify or transform the electric scooter, including the steering system, folding system and rear brake.

Follow the manufacturer’s instructions and do not make any modifications that are not explicitly stated in the instruction manual.

The Joyor electric scooter suspension is non-adjustable. We request that you refrain from attempting any adjustments.

Before using the equipment, tighten all the fastening screws of the screen with the accelerator and the brake lever, making sure that these components are fixed and do not move, to avoid vibrations.

To prevent the handlebar vibrations and shaking adjust and, if necessary, loosen the screws inside the handlebar sleeves when folded.

Before using the equipment, make sure that there are no loose cables on the rear wheel and motor part, to avoid high noise from the motor.

Every 2 months it is recommended to check and tighten the nuts on the rear wheel of the motor, to avoid vibrations and high noise from the motor.

The first assembling involves inserting the handlebar stem into the main tube and securing it. Then, attach the display/control unit to the handlebars and tighten the screws to secure it. Refer to the assembly diagrams provided in the manual for visual guidance.

To unfold: Release the folding mechanism latch, typically located near the base of the handlebar stem. Raise the handlebar stem upwards until it locks into the upright position. Ensure it clicks or is otherwise securely locked. If your handlebars also fold, unfold them.

To fold: If applicable, fold the handlebars first. Release the folding mechanism latch. Lower the handlebar stem towards the scooter deck until it engages and locks into the folded position. Refer to the folding/unfolding diagrams in the manual for visual guidance.

The Home Screen displays:

1. Error code display

2. Power gear display

3. Speed Display

4. Cruise indicator

5. Battery display

6. Starting mode (ECO/NORMAL)

7. Single/dual drive riding (S-drive/D-drive)

8. Lighting indicator

9. 6km/h boost mode indicator

10. Multifunctional display (shows ODO, TRIP, Voltage, etc.)

From bottom to top, the battery level increases sequentially, the lowermost display grid represents low battery, and the uppermost display grid represents high battery. The left side displays the corresponding remaining battery percentage.

Display total mileage, single mileage, real-time voltage display, running time prompt, fault prompt and switch handle voltage value.

Mode selection, the default mode is single drive. S-drive is one motor drive and D-drive is two motors drive.

ECO is non-zero startup mode and NORMAL is Zero startup mode.

Press the Power (O) button and – (minus) button simultaneously for 3 seconds to enter the setting interface or return to the main interface. Short press the Power (O) button to switch setting options. After setting, long press + (plus) and – (minus) simultaneously to return to the main interface.

After entering the setting interface, then press the Power (O) button to switch to P02. Press the + (plus) or – (minus) button to select O (MILE-default) or 1 (KM).

After entering the setting interface, then press the Power (O) button to switch to P04. Press the + (plus) or – (minus) button to select from 0 to 60 minutes (0 means always on). Default is 5 minutes.

After entering the setting interface, then press the Power (O) button to switch to P06. Press the + (plus) or – (minus) button to select the diameter (Calculated by inch, the precision is 0.1). Default is 10.

Range: 1-100. After entering the setting interface, then press the Power (O) button to switch to P07. Press the + (plus) or – (minus) button to select the number of the magnets. Default is 30.

After entering the setting interface, then press the Power (O) button to switch to P09. Press the + (plus) or – (minus) button to select 0 (Zero start) or 1 (Non-zero start). Note: The system default is 1 (non zero startups). After startup, it defaults to gear 0. In order to ride safely, please confirm to start in gear 1. Then press down the acceleration handle while sliding with your feet to start riding.

Range: 0 to 5. After entering the setting interface, then press the Power (O) button to switch to P12. Press the + (plus) or – (minus) button to select the strength. Default is 5.

Range: 1 to 100. After entering the setting interface, then press the Power (O) button to switch to P15. Press the + (plus) or – (minus) button to select the percentage. Default is 100.

After entering the setting interface, then press the Power (O) button to switch to P16. Press the + (plus) or – (minus) button to select O (OFF) or 1 (ON). After starting cruise, press the acceleration handle until the cruise icon lights up. At this time, releasing the handle will not stop the assistance. When shifting gears, braking or pressing the acceleration handle again, you will exit cruise.

Enter the menu, short press the + (plus) or – (minus) key, the value 00099 flashes, and the display returns to the main interface after long-pressing the Power (O) key for 5 seconds, the setting is successfully done.

In the ODO parameter setting interface, briefly press the + (plus) button and then press and hold for 5-6 seconds until the number is zero.

Choose a suitable venue for riding.

Unfold the electric scooter according to the instructions.

Adjust the height of the handlebar tube according to your height.

Press the power button to turn on the power. The speed is set by default to gear level 1.

For safety purposes, Joyor electric scooter has a safe start design which means the motor can start only when the speed of the vehicle is above O. It prevents motor start when the acceleration handle is pressed by mistake.

To start the riding operations, put one foot on the standing board and the other foot on the ground and kick scoot it like a classic kick scooter. When the scooter is in motion and its speed is above O, smoothly use the acceleration handle to start the motor.

Once the motor starts, put the other foot on the standing board and continue riding.

When riding, adjust the gear level from 1 to 3, use lights and horn according to the road conditions and according to the situation.

Be aware of the cruise control function. Cruise control function is activated when the acceleration handle is pressed with the same pressure for 3 seconds (if enabled in settings).

Be aware of the possibility of unpredictable sudden obstacles on your way and control the speed level.

Use the rear brakes handle for braking under normal circumstances. Use front brake handle for braking in emergency situations.

The greater pressure you put, the greater braking force will be applied. Be aware that hard braking may result in an accident due to slipping of the wheels, loss of balance and fall of the vehicle. Hard braking might also cause damage to the tyre.

Joyor electric scooter uses rubber elastic tyres. When the tyres are worn out or have a puncture, they need to be replaced timely.

Contact the official distributor to replace the original tyres.

Inspect your scooter and its tyres every month, check if the screws are tightened enough. If they are loose, tighten them.

Joyor electric scooter is equipped with a lithium polymer battery. The average lifespan of the battery is 1000 cycles. Under normal use and maintenance, the battery lifespan can generally reach more than 1000 cycles.

Before using the scooter for the first time, please charge the battery to the full charge.

Always make sure it is minimum 10 % charged. For satisfactory vehicle performance, the battery has to be charged minimum 50%.

Always use only the original Joyor charger that corresponds to the model of the scooter.

Keep the battery dry. Negative environmental conditions can damage the battery.

Polymer lithium batteries have to be treated with extreme caution. Unappropriated charging, damage or overheating can result in a fire. Do not leave your electric scooter to charge without supervision. Do not leave the electric scooter to charge overnight. Always supervise the electric scooter while it is charging and avoid battery over-charge. Do not use, charge or leave a damaged battery unattended and follow the disposal protocols immediately.

1. Never let the battery fully discharge, recharge it promptly!

2. Charge the battery to 30-70% of its total capacity, avoiding complete depletion before charging.

3. Charge the battery uninterrupted to 100% at least every three charging cycles.

4. Allow the battery to cool for 30 minutes after long distance rides or in cold conditions before charging.

5. Before storing, charge the battery to 70% if it will not be used for months. Monthly, turn on and recharge the scooter’s battery, allowing the motor to run briefly.

6. Avoid exposing the scooter to direct sunlight or extreme cold when parking or storing. Store it at an appropriate room temperature.

Joyor S series chargers: 54.6V (S5-Z), 67.2V (S10-S-Z).

54.6V: Input 100-240V ~, 2.8A / 3A (MAX) 50 / 60Hz; Output 54.6V = 2.0A.

67.2V: Input 100-240V ~, 2.8A (MAX) 50 / 60Hz; Output 67.2V = 2.0A.

WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance. The dedicated charger provided by Joyor has a charging protection timing function.

Ensure your scooter is turned off before you attempt to charge the battery.

Open the charging port cover on the electric scooter and insert the charger output connector into the charging port.

Insert the charger input power plug into the power socket (AC110V-220V).

Charger light is red to indicate that charging is in progress; when the charger light turns green, it indicates that the battery is fully charged.

When charging the battery, place it in a dry, ventilated environment.

Please check and adjust screws monthly. Under conditions of professional or intensive use, it is recommended to change the screws every 6 months.

Please frequently check and adjust the breaks.

To request warranty service, you may contact Joyor or contact an authorized Joyor distributor. Joyor will not provide any warranty coverage unless your claim it in compliance with all terms of this limited warranty statement and you follow the proper return procedure.