JEFFERSON JEFCEMPETORG-l2 (01) PDF DOCUMENT

The JEFFERSON JEFCEMPETORG-l2 is a powerful and reliable petrol driven cement mixer with the following features:

A quality 3.5hp Loncin engine.

Drum tilt action allows for easy pouring & cleaning.

Orange powder coated finish with UV-Protection.

Compact and portable for easy transportation.

Fitted with barrow height swivel.

Complete with tripod stand and rubber wheels.

1. Remove all components from the packaging and check for damage.

2. Place the frame on a level surface and slide both wheels onto the main frame axle (secure with the R clips included in the assembly kit.)

3. Remove the engine from its packing, attach the spacer key pulley and washers to the crankshaft and fix with the relevant bolt provided.

4. Remove the right hand section of the upper belt guard, a drive belt is pre-installed under this cover.

5. Assemble the engine by first insuring that the belt is fitted on the engine pulley. Fix the engine to the base plate using the 4mm x 6mm x 35mm nuts and bolts and washers provided.

Important: After unpacking, inspect the equipment carefully and ensure that the product is in perfect condition without any defects or no damaged or worn parts.

Please dispose of all the packaging materials appropriately, recycling all materials where facilities are available.

Ensure that you have read and fully understand all of the operating instructions, safety precautions and warnings in this manual before operating or maintaining this equipment. Most accidents are caused by the failure to observe basic safety rules or precautions. Never use this equipment or modify it in any way that has not been specifically recommended by the manufacturer. Ensure that you check the equipment thoroughly to ensure it is safe and fit for purpose before each use. It is important that you inspect all plugs, sockets, power cables and electrical fittings for wear and damage and repair or replace any defective components.

1. Familiarise yourself with this equipment and its operation before use – read this user manual carefully before use. Save for future reference.

2. This appliance is for outdoor use only. Ensure that all bystanders are kept at a safe distance and that animals and children are kept from the work area.

3. Never use this equipment if any part or accessory is damaged or malfunctioning.

4. Always shut the equipment off completely when not in use and if left unattended.

5. Ensure that the equipment is completely shutdown and disconnected from the mains before carrying out any servicing or repairs.

6. Only use approved replacement parts to repair this equipment. Never modify the equipment in anyway. Ensure that the equipment is kept in good working order and cleaned and serviced regularly. Check the external nuts and fixings regularly to ensure that they have not loosened from vibration during use.

7. Ensure that the electrical cable is fully protected and there is no danger of damage for equipment or materials. Always inspect the cable before use and replace if any damage is apparent.

8. Do not wear jewellery or loose clothing that could be snagged by the rotating drum.

9. Keep your hands clear of the rotating drum at all times. Never put your hands inside of the drum when the machine is running.

10. Ensure that the safety guards are always used.

11. This equipment is heavy and requires two people to lift and assemble.

12. Ensure that the equipment is operated from a stable even surface.

13. Do not load the drum when the machine is switched off. Always ensure that the drum is rotating before gradually adding the mix. This will help to preserve the motor and gearbox.

14. Do not allow water to come into contact with the motor or electrical components.

15. Do not operate under the influence of alcohol or drugs.

16. Keep the drum free from debris and mortar build up (clean after every use).

17. Keep all moving parts (wheel axles, swivel brackets etc.) lightly greased.

18. Petrol engines can become hot in use, do not refuel or touch hot engine parts until they have had a chance to cool down.

19. Wear appropriate Personal Protection Equipment as required.

1. Start the mixer and ensure that the drum is rotating.

2. Add water to prevent contents sticking to the drum.

3. Add the cement.

4. Add the aggregate.

5. Mix to the consistency required.

6. Tilt the drum using the handles to pour when ready.

Inspect the power cable to ensure that it is completely free from damage and that all fittings are tight and secure.

Inject a few drops of light oil onto the moving parts (wheel axles, swivel brackets etc.)

Hose down the drum and stand with clean water. Take care to prevent any water entering the motor housing and electrical components by protecting them with waterproof covering during the cleaning process.

Check oil regularly and fill as required. Keep parts clean and service regularly.

Store in a safe dry environment away from children and animals.

Recycle any packaging and unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable, reaches the end of its working life and requires disposal, drain off any fluids (if applicable) into approved containers and dispose of the product and the fluids according to local regulations.