Free English JABLOTRON JB-161N-PLUG (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD JABLOTRON JB-161N-PLUG (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the JABLOTRON JB-161N-PLUG intended for?
The JABLOTRON JB-161N-PLUG is a bidirectional wireless component of the JABLOTRON system. It can copy PG output when it is enrolled to a JA-10xK control panel. It provides safe separation of relay contact for a power load switch up to 250 V/16 A (4000 W). The plug occupies one position in the system.
How do I install and enroll the JABLOTRON JB-161N-PLUG into the system?
To install and enroll the device, follow these steps:
1. Plug the product into the power outlet. Note that for proper function and app control, a radio module JA-11xR must be installed in the system.
2. Proceed according to the control panel installation manual using the following basic procedure:
a. When the plug is switched on, the yellow LED (2) indicates that the plug has not been enrolled into the system.
b. In the F-Link software, select the required position in the Devices tab and launch the enrollment mode by clicking on the Enroll option.
c. Press the enrollment button (2). When the device is enrolled, the LED status will change from yellow to green.
How can I control the relay on the JABLOTRON JB-161N-PLUG locally?
You can control the relay by pressing the button (2) located on the front panel of the plug.
How do I configure the properties and settings for the JABLOTRON JB-161N-PLUG?
Settings are located in the F-link software under the Device tab – Internal settings. The available settings include:
Reacts to PG: You can set the PG that the plug will copy.
Button controls the PG: You can set the PG that is activated by the button (2).
Optical indication:
– Indicates permanently: Status of PG output is indicated permanently.
– By status change: Status of PG output is indicated for 3 seconds after a change.
– Disabled: Indication is turned off for the status of PG output and for its change.
What do the LED colors indicate on the JABLOTRON JB-161N-PLUG?
The status of the relay is indicated by the backlit button (2):
Green: The relay is turned off, and the socket is not powered.
Red: The relay is turned on, the socket is powered, and connected devices are also powered.
Yellow: Indicates a fault of communication with the control panel or the status that it is not enrolled to the system.
How does the JABLOTRON JB-161N-PLUG behave during a power or communication loss?
In case of power loss or communication loss longer than 20 minutes, the relay is turned off. Communication loss is indicated by a yellow permanent light. After recovery of the power or communication with the control panel, the plug will restore status according to the assigned PG.
What are the technical specifications of the JABLOTRON JB-161N-PLUG?
| Power supply | 110–230 V/50–60 Hz |
| Power consumption at 230 V AC (min/max) | 0.4 W/1 W |
| Communication band | 868.1 MHz, Jablotron protocol |
| Maximum radio-frequency power (ERP) | 25 mW |
| Antenna | Internal |
| Relay contact load ability – class protection II + FE | |
| Maximum acceptable relay voltage | 250 V AC |
| Resistive load (cos φ = 1) | Max. 16 A |
| Inductive, capacitive load (cos φ = 0.4) | Max. 8 A |
| Dimensions | 70 x 70 x 77.6 mm |
| Weight | 105 g |
| Operating temperature range | -10 °C to + 40 °C |
| Average operating humidity | 75% RH, non-condensing |
CLICK HERE TO DOWNLOAD JABLOTRON JB-161N-PLUG (01) PDF DOCUMENT