ISOTUNES FREE 2.0 IT-72 (02) PDF MANUAL

This guide covers the following models:

IT-73, IT-74: ISOtunes FREE 2.0

IT-72: ISOtunes FREE 2.0 EN 352

The ISOtunes FREE 2.0 comes with:

3 sets of TRILOGY™ tall foam eartips (S,M,L).

3 sets of double flange silicone eartips (S,M,L).

Choose the size that fits best in your ear canal. Remember, the snugger the fit, the better the noise reduction. The silicone eartips are not tested for noise-attenuation and should not be used in noisy environments.

1. Carefully roll the foam eartip on the stem/sound port.

2. Insert the eartip into your ear as deeply as comfortable.

3. Slightly rotate earbud until it is secure in the bowl of your ear.

4. Make the earbud rest tightly next to your inner ear edge.

Method 1

Power ON: Remove earbuds from charging case.

Power OFF: Place earbuds into charging case.

Method 2

Power ON: In OFF mode, press and hold multi-function button (MFB) for 3 seconds.

Power OFF: In ON mode, press and hold MFB for 6 seconds.

After powering on, the earbuds will automatically enter Bluetooth® Pairing Mode. Look for quick red and blue flashes from the earbud as a confirmation. Open the Bluetooth® settings on your device. Search for “ISOtunes FREE 2.0″. Pair and connect. You will hear “Bluetooth® Connected” once connected.

There are three batteries to charge: the Charging Case Battery, the Left Earbud Battery, and the Right Earbud Battery.

Charging the Case

Insert USB type C charging cable into the charging case. The charging case battery indicator light will start flashing to indicate charge level.

Charging the Earbuds

Place earbuds into the charging case. The earbuds’ red indicator light should be solid red, indicating that the earbuds are charging.

Only charge your ISOtunes FREE 2.0 with a Maximum 5 Volt charger. Using a charger higher than 5 Volts could be dangerous and may damage your ISOtunes product. Be especially careful with “quick charge” or “turbo charge” chargers, which often supply 9, 12, or 15 Volts. Your ISOtunes FREE 2.0 cannot be charged at voltage levels above 5 volts.

Clean your ISOtunes FREE 2.0 by gently wiping them with a clean, damp cloth with mild soap.

Do not immerse the earbuds in water.

Do not use abrasive cleaning solvents to clean the earbuds.

If the earbuds get wet from sweat or rain, please discontinue use and allow them to dry.

ISOtunes® FREE 2.0 incorporates SafeMax™ Technology, therefore its volume output has been limited to 85 decibels (IT-73 & IT-74), or 79 decibels (IT-72). ISOtunes® devices with SafeMax™ Technology are OSHA and ANSI compliant.

The level of noise entering a person’s ear, when ISOtunes® FREE 2.0 earbuds are worn as directed, is closely approximated by the difference between the A-weighted environmental noise level and the Noise Reduction Rating (NRR). Improper fit of this device will reduce its effectiveness in attenuating noise.

The NRR for ISOtunes® FREE 2.0 is 25 dB.

Example:

1. The surrounding noise level measured at the ear is 100 dB.

2. The NRR of ISOtunes® FREE 2.0 is 25 dB.

3. The noise level entering the ear is approximately equal to 75 dB.

Please note that the NRR is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise, such as gunfire.

This product has been tested to the European Safety Standard EN 352-2:2020. The key for the table values is as follows:

H = Hearing protection estimation for high frequency sounds (f ≥ 2000Hz)

M = Hearing protection estimation for medium frequency sounds (500 Hz < f < 2000Hz)

L = Hearing protection estimation for low frequency sounds (f ≤ 500Hz)

EN 352-2:2002 Table (SNR Table)

Short Eartips

SNR (dB) = 32.0

H84 (dB) = 32 dB

M84 (dB) = 30 dB

L84 (dB) = 28 dB

Tall Eartips

SNR (dB) = 33.0

H84 (dB) = 32 dB

M84 (dB) = 31 dB

L84 (dB) = 29 dB

ISOtunes® FREE 2.0 does an excellent job of blocking outside noise. As such, ISOtunes® FREE 2.0 should NOT be used in environments where users need to be fully aware of their surroundings for personal safety reasons. For example, do NOT use them while driving a car or riding a motorcycle. Similarly, do NOT use them when riding a bicycle outside. The user is solely responsible for ensuring that ISOtunes® FREE 2.0 is used ONLY in safe environments.

FCC ID: 2AJRDIT-72

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.