IMG STAGELINE PAK-12DMP (01) PDF DOCUMENT

The IMG STAGELINE PAK-12DMP corresponds to all relevant directives of the EU and is therefore marked with CE. Please observe the following safety notes:

WARNING: The unit uses dangerous mains voltage. Leave servicing to skilled personnel only. Inexpert handling or modification of the unit may result in electric shock.

The unit is suitable for indoor use only. Protect it against dripping water and splash water, high air humidity, and heat. The admissible ambient temperature range is 0-40°C.

Do not place any vessel filled with liquid on the unit, e. g., a drinking glass.

The heat produced inside the speaker system must be dissipated by the cooling fins. Therefore, never cover the cooling fins. Never place the speaker system directly on a wall; always keep a corresponding distance.

Immediately disconnect the mains plug from the socket if:

1. The unit or the mains cable is visibly damaged.

2. A defect might have occurred after the unit was dropped or suffered a similar accident.

3. Malfunctions occur.

In any case, the unit must be repaired by skilled personnel.

Never pull the mains cable to disconnect the mains plug from the socket; always seize the plug.

For cleaning, only use a dry, soft cloth; never use water or chemicals.

If the unit is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

Place the IMG STAGELINE PAK-12DMP on a solid surface and align it towards the audience. Place the tweeters at ear level, if possible. The PAK-12DMP is equipped with additional feet at the lateral handles and can also be operated horizontally as stage monitors; in this position, sound will be radiated diagonally upwards.

Alternatively, place the speaker system via the stand sleeve on its lower side on a standard speaker stand with a tube diameter of 35 mm.

For additional mounting options, e.g., suspension, the upper and lower sides of the cabinet are provided with M8 threaded jacks. To use these jacks, remove the cover caps.

Set up the speaker system in such a way that air will be able to flow freely through the cooling fins; otherwise, there may be overheating and the protective circuit will mute the sound.

Before making or changing any connections, switch off the IMG STAGELINE PAK-12DMP and the units to be connected.

1) To connect a microphone:

Use the XLR jack or 6.3 mm jack MIC IN.

2) To connect an audio unit with line output (e.g. mixer, CD player):

Use one of the following input jacks:

• 3.5 mm jack AUX

• RCA jacks LINE IN L/R

• XLR jack LINE IN

3) To connect an additional speaker system or recorder:

If an additional active speaker system is required for PA applications of larger zones, connect the line input of this speaker system to the XLR output MIX OUT. Alternatively, connect a recorder to this jack.

4) For power supply:

Use the mains cable provided to connect the mains jack on the rear to a mains socket (230 V/50 Hz).

1. To switch on the IMG STAGELINE PAK-12DMP, use the mains switch POWER. The display will briefly show “HI” and the green LED ON will light up.

2. Use the controls LEVEL 1 and LEVEL 2 to adjust the desired volume for the microphone connected and/or for the units connected. Use the control MP3/BT/FM LEVEL to adjust the volume for the MP3 player/radio/Bluetooth module. If the module or an input is not used, set the corresponding control to MIN.

CAUTION: Never adjust a very high volume. Permanent high volumes may damage your hearing! Your ear will get accustomed to high volumes which do not seem to be that high after some time. Therefore, do not further increase a high volume after getting used to it.

3. Use the controls TREBLE and BASS to adjust the sound. This will not affect the sound of the output signal of the jack MIX OUT.

4. If the red LED CLIP lights up, the volume is too high which will result in distortion. If the LED keeps lighting and there is substantial distortion, the speakers may be damaged. When the LED CLIP lights up, turn back the corresponding control.

The remote control is supplied with a battery. Before the first operation, remove the protective film from the battery holder. When you press a button, always point the remote control at the front of the speaker system. Make sure that there are no obstacles between the speaker system and the remote control. If not in use for a long period, remove the battery to prevent damage due to battery leakage.

To switch on the module, use the button MODE, if necessary: Keep the button pressed for 2 seconds. All control options can be found in the table below.

To replay MP3 files, connect a USB flash drive or a hard disk with separate power supply to the USB port and/or insert a memory card into the slot SD, notched corner facing upwards and towards the unit. To remove the card, push the card into the slot until it disengages.

Note: Due to the large number of storage device manufacturers and device drivers, it cannot be guaranteed that all storage media are compatible with the MP3 player.

Button (on remote control ↓ / on the unit ↓)	Function
MP3 player/radio/Bluetooth module
MODE (↓/↓)	To switch on/off: keep the button pressed for 2 seconds. To switch over between: 1. MP3 replay from a memory card (indication: SD) 2. MP3 replay via USB port (indication: USB) 3. FM radio (indication: FM) 4. Bluetooth receiver (indication: – – – – *)
VOL- VOL+ (↓)	To adjust the volume (in addition to the control MP3/BT/FM LEVEL on the speaker system)
MUTE (↓)	To mute and unmute the sound
MP3 player
►II (↓/↓)	To switch between replay and pause
RPT (↓)	Repeat function and random replay ONE = repeat of the title ALL = repeat of all titles Rdo = continuous replay of the titles in random order
◄◄ / ►► (↓/↓)	Title beginning, previous/next title
0…9, 100+, 200+ (↓)	For direct title selection, examples: Title: 8, Button(s): 8 Title: 15, Button(s): 1, 5 Title: 100, Button(s): 100+ Title: 103, Button(s): 100+, 3 Title: 124, Button(s): 100+, 9, 9, 6 Title: 250, Button(s): 200+, 9, 9, 9, 9, 9, 5
EQ (↓)	To select sound settings
STOP (↓)	To stop the replay
FM radio
►II (↓)	To find all radio stations and to store them automatically one after another: Keep the button pressed for 2 seconds until the numbers of the frequency indication start scrolling. In the radio mode, the button ►II on the remote control is without function.
0…9 (↓)	To call up a stored station
◄◄ / ►► (↓/↓)	Press briefly: previous/next station. Keep pressed for 1 second to start station scanning.
Bluetooth receiver
MODE (↓/↓)	1. Press the button MODE repeatedly until – – – – * starts flashing on the display. 2. Activate the Bluetooth function of the Bluetooth signal source. 3. Link the Bluetooth signal source to the active speaker system. When the connection has been made, the display will stop flashing. 4. Start the replay on the Bluetooth signal source.
►II (↓/↓)	To switch between replay and pause²
◄◄ / ►► (↓/↓)	Title beginning, previous/next title²

¹ The Bluetooth signal source must use the A2DP profile (Advanced Audio Distribution Profile); otherwise, wireless transmission will not be possible.

² The Bluetooth signal source can only be controlled via the active speaker system if it uses the AVRC profile (Audio Video Remote Control Profile).

1. Push the latch of the battery support to the right and pull out the support.

2. Remove the discharged battery and insert the new battery (3V button cell of the type CR2025) into the support, with the positive pole facing up.

3. Push the support back into the remote control.

Never put discharged batteries in the household waste. To protect the environment, always take them to a special waste disposal, e.g., a collection container at your retailer.

Amplifier power (RMS/MAX)	90W / 180W
Frequency range	50 Hz – 20 kHz
Max. SPL	115 dB
Bass speaker	30 cm (12″)
Tweeter	dynamic horn tweeter, 25 mm (1″)
Inputs (sensitivity/impedance) Mic XLR, bal. Mic 6.3 mm jack, unbal. Line 2 3.5 mm jack, unbal. Line 2 RCA, unbal. Line 2 XLR, bal.	12 mV / 2 kΩ 30 mV / 4 kΩ 500 mV / 8 kΩ 500 mV / 8 kΩ 460 mV / 8 kΩ
Ambient temperature	0-40°C
Power supply	230V/50Hz
Max. power consumption	200 VA
Dimensions (W × H × D)	370 × 590 × 290 mm
Weight	11.2 kg