IBIZA SOUND DJ21USB-MKII (01) PDF MANUAL

The stereo mixer features:

3x Stereo Channels

2x Phono, 3x Line, 1x USB and 2x Mic Inputs

Talkover

Headphone monitor

Master output level meter

Load and play MP3’s into the USB stick with led display

All operating instructions should be read before using this equipment.

Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.

This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.

When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.

To prevent electric shock, do not remove top or bottom covers.

No user serviceable parts inside.

Refer servicing to qualified servicing personnel.

Disconnect power cord before removing back panel cover to access gain switch.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

The unit should only be used in moderate climates.

A minimum distance of 0.5m around the unit must be kept to ensure sufficient ventilation and avoid overheating.

1. Before using this unit, make sure that the AC Adaptor (21) is correct voltage.

2. The unit is supplied with AMP output jacks. The AMP (20) jacks are unbalanced and used to connect to your amplifier.

3. The MIC L (15) and MIC R (16) input accepts a 1/4″ connector.

4. On the rear panel are two stereo PHONO/LINE (17) & (18) inputs and 1 stereo LINE (19) input. The PHONO/LINE (4) enables you to set the (17) input to phono or Line. The PHONO/LINE (6) enables you to set the (18) input to phono or Line. The USB/LINE (8) enables you to set the input to USB or Line (19). Headphones can be plugged into the rear panel mounted HEADPHONE (14) jack.

1. POWER ON: Once you have made all the equipment connections to your mixer, press the POWER (12). The power will turn on and the POWER LED (22) will glow RED.

2. CHANNEL 1: SWITCH (4) allows you to select the PHONO 1/LINE 1 (17) jack to input phono or line level. The CHANNEL SLIDE (5) controls the input level of this channel.

3. CHANNEL 2: SWITCH (6) allows you to select the PHONO 2/LINE 2 (18) jack to input phono or line level. The CHANNEL SLIDE (7) controls the input level of this channel.

4. CHANNEL 3: SWITCH (8) allows you to select the USB OR LINE 2 (19) jack to input mp3 or line level. The CHANNEL SLIDE (9) controls the input level of this channel.

5. CROSSFADER: The CROSSFADER (10) allows you to the Mixing CH1/CH2 source into another.

6. TALKOVER (3): The purpose of the talkover section is to allow the program playing to be muted so that the mic can be heard above the music. When you press the SWITCH, the talkover will be on and the volume of all sources except the Mic inputs are lowered by 12 dB. The Micro (2) allows you to control the level of MIC1/MIC2.

7. Connect your headphones to the headphones socket and select the desired channel (channel 1-3 or MIC) for monitoring with the Cue switch(1). With this knob PHONE(11), you can adjust the headphones volume.

8. DISPLAY: The DISPLAY (13) indicates either the MASTER output left and right levels.

9. The USB (23) jack can connect to USB stick that contains exclusively MP3 files.

10. |<< (24): Use this button to re-start the track or to select the previous track.

11. Play/Pause (25): Each time you press this button, the operation changes from play to pause or from pause to play.

12. >>| (26): Use this button to select the next track.

13. VOL-(27): Use this button to control level down of the MP3 player.

14. VOL+ (28): Use this button to control level UP op the MP3 player.

15. EQ (29): Allow you to select the effect.

16. LED DISPLAY (30): Display to MP3’s information.

MIC L&MIC R sensitivity	1.5 mV (10 K ohms)
PHONO sensitivity	3mV (47 K ohms)
LINE/CD sensitivity	150 mV (22 K ohms)
MASTER OUTPUT	nominal 775 mV MAX 1.5 V
Frequency Response	20Hz-20KHz ±2dB
Talkover attenuation	-12dB
Headphone output	300mV/8-16 ohms