HYGGER HG165 (01) PDF DOCUMENT

The HYGGER HG165 offers the following features:

• The 24-volt DC power adapter is safe and energy efficient and consumes little power. Super quiet motor.

• Adjustable wave modes, flow rates, and wave frequencies.

• The super-quiet wave pump is controlled using sine wave technology.

• The strong magnetic holder is easy to install and move around.

• This pump is suitable for freshwater, saltwater, and reef aquariums.

• The pump is suitable for glass thicknesses up to 5/8 inches (15 mm).

1. Detach the magnetic holder from the pump body.

2. Connect the wave pump to the controller and the controller to the power adapter. Plug in and go.

3. Place the pump at least 3 inches (7-8CM) underwater and attach it to the outer glass of the aquarium using the magnetic holder.

CAUTION: Be careful not to pinch your fingers; the magnet is very strong.

The controller for the HYGGER HG165 has the following button functions:

M Button (Mode Key): Press once to select the wave mode from the four wave modes: Constant Wave Mode ==> Classic Cross-flow Wave Mode ==> Sine Wave Mode ==> Random Wave Mode.

“+” or “-” Button: Press “+” or “-” to adjust the flow rate or frequency from 1 to 20.

a. ONLY in constant wave mode can flow rates (from 1 to 20) be set; the frequency cannot be set.

b. ONLY in Classic Cross-flow Wave Mode, Sine Wave Mode, and Random Wave Mode can frequency (from 1 to 20) be set; the flow rate cannot be adjusted.

F Button (Feed Button): Press briefly to activate the 10-minute feeding. Press again to select between feeding minutes (20-30-60 minutes). Then press again to activate standby mode and then press to return to the normal operating state.

1. Briefly press the “M” button until the icon of Constant Wave Mode lights up. The green indicator light “Flow” at the upper right corner will also light up.

2. Then briefly press the “+” or “-” button to select the flow rate, which can be set from 1 to a maximum of 20 levels. Two indicator lights will light up to show that the setting is complete and the pump will operate in the corresponding mode.

Attention: ONLY in constant wave mode can flow rates (from 1 to 20) be set; the frequency cannot be set.

1. Briefly press the “M” button, and the icon of the desired wave mode (e.g., Classic Wave) will light up. The green indicator light “Freq” at the upper right corner will also light up. Press the “M” button alternately to select the desired wave mode. When a wave mode is selected, the corresponding indicator will light up.

2. Then briefly press the “+” or “-” button to adjust the frequency of the selected mode (Classic Cross-flow Wave Mode, Sine Wave Mode, or Random Wave Mode).

Attention: ONLY in Classic Cross-flow Wave Mode, Sine Wave Mode, and Random Wave Mode can frequency be set; the flow rate cannot be adjusted.

1. The pump is delivered from the factory with the night mode light switched on automatically. The green night mode indicator light is always illuminated to indicate that this mode is switched on. However, this does not mean that the pump is operating in night mode at this time, but only when the light sensor detects that the light is dimming. When the light sensor is switched ON, the night indicator lights up green, the pump operates in a low flow rate, and “01” is displayed.

2. To switch Night Mode OFF, press and hold the “M” button. The green indicator will not light up, meaning that the night mode is switched off.

3. To switch Night Mode ON again, press and hold the “M” button, and the green “Night” indicator will light up.

Briefly press the “F” button to activate the 10-minute feeding, and the green indicator “Flow” will light up. Press again to select between feeding minutes (20-30-60 minutes). Then press again to activate standby mode and then press to return to the normal operating state.

• Before starting up for the first time, make sure that your fish and invertebrates in the aquarium are larger than the grid size of the cover so that no animals are drawn into the pump.

• The controller is not waterproof. Please avoid contact with water to prevent electric shock and damage or injury.

• The pump should never run dry. Ensure that the appliance is always fully submerged when it is running; the water should be at least 3 inches (7-8CM) higher than the top edge of the pump to prevent damage.

• Never allow the pump to run dry for longer than 5 minutes. During operation, the device should always be completely covered by water to ensure a certain degree of cooling.

• The device is suitable for use in fresh and salt water. Do not use it in flammable, acidic or corrosive liquids.

• The appliance operates in clean water in a temperature range between 4 °C (39°F) and 35°C (95°F).

• Never lift the device directly by the cable to avoid damaging it.

• Please ensure that the controller is not placed in a dark location, so as not to cause the night function to fail.

• The pump housing is held to the aquarium glass by a very strong magnet. Make sure that the two magnetic sides of the holder are never brought together without protection in between; they are very difficult to separate again.

1. Before carrying out maintenance work, always disconnect the appliance from the power supply.

2. First disconnect the plug connection from the controller and pump. Remove the cover on the front of the pump and remove the impeller and axle. Then carefully clean all pump parts with a soft brush in clear water. After cleaning, reassemble the device as explained in the relevant operating instructions.

3. Make sure that the plug connections never get wet during cleaning.

Please note: Always disconnect the appliance from the power supply before troubleshooting.

If your pump switches off, it could be due to dirty water or high water temperature. If an error code is displayed, refer to the table below.

To avoid possible electric shock, do not immerse the switch in the water. If the switch falls into the water or becomes wet, do not touch it until you have unplugged it. Basic safety precautions that should be observed are as follows:

1. Read and follow this user manual strictly.

2. DANGER – To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt to repair yourself. Instead, return the pump to an authorized service facility for maintenance or discard it.

A. If the pump shows any sign of abnormal water leakage or RCD (or GFCI – Ground Fault Current Interrupter), unplug the power and remove the pump from water.

B. Carefully examine the pump after installation. It should not be plugged in if there is water on parts that are not intended to be wet.

C. Do not operate the pump if it has a damaged cord or plug, is malfunctioning, dropped or damaged in any manner. The power cord of this pump cannot be replaced. If the cord is damaged, the pump should be discarded.

D. To avoid the possibility of the pump plug getting wet, position the aquarium and its stand to one side of a wall mounted outlet to prevent water from dripping onto the outlet or plug. A “drip loop” should be arranged by the user for each cord, which connects the pump to the outlet. The “drip loop” is the part of the cord below the level of the outlet or the connector that prevents water from traveling along the cord and coming in contact with the outlet. If the plug or outlet does get wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the pump. Then unplug and examine for the presence of water in the outlet. If you are not sure, consult a certified electrician.

The packing list includes:

• 1x Controller

• 1x Power adapter

• 1x 3M sticker

• 1x Pump

• 1x User manual