HP DESKJET 3070A E-ALL-IN-ONE (01) PDF Document

ePrint is a free HP service that provides a safe and easy way to print by sending an email to your printer’s email address. If you can send an email, you can use ePrint.

To use ePrint your printer must be connected to the internet on a wired or wireless network.

If you did not enable ePrint when you first installed your printer software, press the ePrint button on the control panel to enable ePrint, and then follow the instructions on the printer display.

When you enable ePrint you will need to agree to the terms of use for web services.

If you have enabled ePrint, press the ePrint button on the control panel to view your printer email address, ePrint status, check and manage product updates, and more.

Auto Wireless Connect will automatically configure the printer with your wireless network settings. Follow the setup poster and the printer display to set up the printer hardware, and then insert the printer software CD. The software will guide you through the software installation. If the Auto Wireless Connect method does not apply for your configuration or operating system, the software will guide you through another wireless installation method.

If you first install the HP Deskjet with a USB connection, you can later change it to a wireless network connection.

Windows

1. From the computer’s start menu, select All Programs or Programs, and then select HP.

2. Select HP Deskjet 3070A series.

3. Select Printer Setup & Software Selection.

4. Select Convert a USB connected printer to wireless. Follow the onscreen instructions.

Mac

Use HP Setup Assistant in Applications/Hewlett-Packard/Device Utilities to change the software connection to wireless for this printer.

You can share the HP Deskjet with other computers which are also connected to your home network. If the HP Deskjet is already connected to your home network and installed on a network computer, for each additional computer you only need to install the HP Deskjet software. During the software installation, the software will automatically discover the HP Deskjet over the network. Since the HP Deskjet is already connected to your network, you do not need to configure it again when installing the HP Deskjet software on additional computers.

Windows

Find electronic Help: After software installation, click Start > All Programs > HP > HP Deskjet 3070A series > Help.

Find Readme: Insert software CD. On software CD locate ReadMe.chm. Click ReadMe.chm to open and then select ReadMe in your language.

Mac

Find electronic Help: From Help, choose Mac Help. In the Help Viewer, click and hold the Home button, and then choose the Help for your device.

Find Readme: Insert the software CD, and then double-click the Read Me folder located at the top-level of the software CD.

Ink from the cartridges is used in the printing process in a number of different ways, including in the initialization process, which prepares the device and cartridges for printing, and in printhead servicing, which keeps print nozzles clear and ink flowing smoothly. In addition, some residual ink is left in the cartridge after it is used.

CQ191-60017

Input voltage: 100-240Vac (+/- 10%)

Input frequency: 50/60Hz (+/- 3Hz)

CQ191-60018

Input voltage: 200-240Vac (+/- 10%)

Input frequency: 50/60Hz (+/- 3Hz)

Note: Use only with the power cord supplied by HP.

1. If your printer is connected directly to your computer with a USB cable, make sure the cable connections are secure.

2. Make sure the printer is powered on. The On button will be lit green.

Make sure the printer is set as your default printing device:

1. Windows 7: From the Windows Start menu, click Devices and Printers.

2. Windows Vista: On the Windows taskbar, click Start, click Control Panel, and then click Printer.

3. Windows XP: On the Windows taskbar, click Start, click Control Panel, and then click Printers and Faxes.

Make sure that your printer has a check mark in the circle next to it. If your printer is not selected as the default printer, right-click the printer icon and choose Set as Default Printer from the menu.

1. Remove the CD from the computer’s CD/DVD drive, and then disconnect the USB cable from the computer.

2. Restart the computer.

3. Insert the printer software CD in the computer’s CD/DVD drive, then follow the onscreen instructions to install the printer software. Do not connect the USB cable until you are told to do so.

4. After the installation finishes, restart the computer.

1. If your printer is connected to your computer with a USB cable, make sure the cable connections are secure.

2. Make sure the printer is powered on. The On button will be lit green.

1. In System Preferences, click Print & Fax.

2. Click the Open Print Queue button.

3. Click a print job to select it.

4. Use the following buttons to manage the print job:

Delete: Cancel the selected print job.

Resume: Continue a paused print job.

5. If you made any changes, try to print again.

1. Restart the computer.

2. Reset the printer.

a. Turn off the printer and unplug the power cord.

b. Wait a minute, then plug the power cord back in and turn on the printer.

Note: The uninstaller removes all of the HP software components that are specific to the device. The uninstaller does not remove components that are shared by other products or programs.

To uninstall the software:

1. Disconnect the HP product from your computer.

2. Open the Applications: Hewlett-Packard folder.

3. Double-click HP Uninstaller. Follow the onscreen instructions.

To install the software:

1. Connect the USB cable.

2. Insert the HP software CD into your computer’s CD/DVD drive.

3. On the desktop, open the CD and then double-click HP Installer.

4. Follow the onscreen and the printed setup instructions that came with the HP product.

If the HP software is unable to find your printer on your wireless network during software installation, try the following troubleshooting steps.

1: Determine if the product is connected to the network

Press the Wireless button. If the printer has been idle, you may need to press the wireless button twice to display the wireless menu.

If the printer is connected, you will see the IP address (for example, 192.168.0.3) on the printer display. If the printer is not connected, you will see Not Connected on the printer display. From the printer display, select Print Reports, then select Wireless Test or Configuration to print the reports. The wireless network test report will display the diagnostic results for the status of the wireless network, wireless signal strength, detected networks, and more. The network configuration page will display the network status, host name, network name, and more.

2: If the product is not connected to a network

If you determined the product is not connected to a network and this is the first time you are installing the software, insert the printer software CD and then follow the onscreen instructions.

If the device is unable to join your network, check for these common issues:

You might have picked the wrong network or typed in your network name (SSID) incorrectly. Check and make sure that you enter the same SSID as the computer is using.

You might have typed in your wireless password (WPA passphrase or WEP key) incorrectly (if you are using encryption).

You might have a router problem. Try restarting both the product and the router by turning off the power for each of them, and then on again.

3: Check for and resolve the following possible conditions

Your computer might not be connected to your network. Make sure that the computer is connected to the same network to which the HP Deskjet is connected. If you are connected wirelessly, for example, it is possible that your computer is connected to a neighbor’s network by mistake.

Your computer might be connected to a Virtual Private Network (VPN). Temporarily disable the VPN before proceeding with the installation. Being connected to a VPN is like being on a different network; you will need to disconnect the VPN to access the product over the home network.

Security software might be causing problems. Security software like anti-virus, anti-spyware, and firewalls can block communication between devices on the home network. A quick troubleshooting technique is to disable your firewall and check if the problem goes away. Sometimes, cycling the power will recover a network communication issue. Turn off the router, printer, and computer, and then turn them back on in this order: router first, then the printer, and finally the computer.

If your firewall has a setting called trusted zone, use it when your computer is connected to your home network.

Keep your firewall up to date. Many security software vendors provide updates which correct known issues.

If your firewall has a setting to not show alert messages, you should disable it. When installing the HP software and using the HP printer, you may see alert messages from your firewall software. You should allow any HP software which causes an alert. The alert message may provide options to allow, permit, or unblock. Also, if the alert has a remember this action or create a rule for this selection, make sure and select it. This is how the firewall learns what can be trusted on your home network.