HOTPOINT FFM76 (01) PDF DOCUMENT

To ensure your HOTPOINT FFM76 fridge freezer runs reliably and efficiently, follow these steps:

1. Choose a location for your fridge freezer, away from any heat sources and allow adequate ventilation – 100mm (4 inch) gap above.

2. Move the fridge freezer into position, using the sides of the cabinet. Take care to avoid damaging the refrigerant circuit pipe work on the rear.

3. Level the fridge freezer by adjusting the front feet. This will stop rocking or vibration and keep the door aligned.

4. Before plugging in and switching on, leave the fridge freezer in its final location for at least 15 minutes to allow it to settle.

5. Plug in and switch on. Allow the fridge freezer to cool before placing food inside. The high temperature light will stay on until the fridge freezer has cooled down. All food in the fridge freezer should be covered.

6. If you are freezing fresh food, turn on fast freeze by pressing the switch 24 hours before placing the food inside. Place the fresh food inside. Remember to turn fast freeze off after 24 hours; however, if you forget to do so, it will automatically cancel after 48 hours.

7. Your fridge freezer is now working. If after 24 hours your fridge freezer is not operating as you want, refer to the Troubleshooting section.

For your safety, please read the following advice:

The fridge freezer cooling system contains a small amount of gas which is environmentally friendly but flammable. To avoid any risk:

• Install the fridge freezer following the installation instructions and ensure that ventilation openings are kept clear of obstruction.

• Take care when installing or moving the fridge freezer to avoid damaging the pipes on the rear.

• If you suspect a leak, do not switch on the fridge freezer, but open the windows and doors to ventilate the room.

• Do not use any electrical devices inside the freezer, for instance for defrosting.

• Do not use any mechanical devices for defrosting other than any which may have been supplied with the freezer as they may cause damage.

• Only use this fridge freezer for storing domestic foodstuffs.

When installing your HOTPOINT FFM76:

• Ensure that the mains cable is not trapped underneath or behind the fridge freezer when you install or move it.

• Do not stack any other appliance on top of this fridge freezer as they may damage the fridge or become unstable.

When using your HOTPOINT FFM76:

• Do not sit or stand on top of your fridge freezer.

• Do not store poisonous, flammable or dangerous substances in your fridge freezer.

• Do not use aerosol sprays for defrosting or cleaning your fridge freezer.

If you sell the fridge freezer, pass on this booklet to the new owner.

Location & Air Circulation

Locate your HOTPOINT FFM76 fridge freezer away from sources of heat e.g. cookers, radiators, direct sunlight as extreme temperature will affect its performance.

Allow a minimum 100mm (4 inches) between the top of the fridge freezer and the ceiling or the underside of a wall cupboard.

Following the recommended ventilation requirements will:

• Prolong the life of the fridge freezer.

• Minimise the risk of condensation on the outside of the fridge freezer.

• Minimise the running costs.

• Minimise operating sounds caused by vibration.

Minimum space required to open door

The fridge freezer needs a space of 600mm (24 inches) in front to allow the door to open. When positioning the fridge freezer next to a unit, a gap of 30mm (1 1/4 inch) can be left at the hinge side of the door to allow the easy removal of furniture. If preferred the fridge freezer can be positioned so that a gap is not left. This will restrict how far the door can be opened but the furniture can still be removed.

Level the HOTPOINT FFM76 fridge freezer when it is in its final location by adjusting the front feet, until firm contact is made with the floor. This will stop rocking or vibration and keep the door aligned which helps the fridge freezer run reliably and efficiently.

Note: Before plugging in and switching on, leave the fridge freezer standing in its final location for at least 15 minutes to allow it to settle.

Electrical Supply

WARNING: This appliance must be earthed.

The appliance must be positioned so that the plug is accessible after installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

• Green/Yellow – Earth

• Blue – Neutral

• Brown – Live

If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown above.

Controlling the Temperature of the Fridge Compartment

The left hand control wheel on the front panel adjusts the internal fridge compartment temperature. The internal temperature should be 5°C or colder, although some sections such as the salad bin will be slightly warmer. The setting of the control wheel will depend on the location of the fridge freezer, the room temperature and how often the door is opened. The normal set point (marked by a 3 on the dial) is usually suitable. If you need to adjust the temperature turn the control wheel using a coin to avoid damage:

• Clockwise (higher number) – Colder

• Anti-clockwise (lower number) – Warmer

Controlling the Temperature of the Freezer Compartment

The right hand control wheel on the front panel adjusts the internal freezer compartment temperature. The internal temperature should be -18°C or colder. The setting of the control wheel will depend on the location of the fridge freezer, the room temperature and how often the door is opened. The normal set point (marked by a 3 on the dial) is usually suitable. If you need to adjust the temperature turn the control wheel using a coin to avoid damage:

• Clockwise (higher number) – Colder

• Anti-clockwise (lower number) – Warmer

Your fridge freezer must NOT be placed in a room where the temperature goes below 6°C or above 38°C for prolonged periods, as the internal fridge temperature will not be maintained.

There are two amber lights which indicate functions are selected:

• The amber fast freeze light indicates that the fast freeze button has been pressed on. By pressing this button ON, the freezer motor will run continuously for extra cooling.

• The amber holiday light (for model FFM76) indicates that the holiday mode is set.

There are two red lights which warn of a rise in temperature in the freezer compartment:

• The red high temperature warning light will come on when the fridge freezer is first switched on or when the temperature inside the compartment rises above the correct storage temperature. It will go out as soon as the compartment returns to its normal storage temperature. The red light may come on for a short period when opening the freezer door to load or unload food, in this case storage times will not be affected. If there has been a power cut resulting in a rise in freezer compartment temperature, the red high temperature warning light will come on as soon as the mains power returns. It will go out as soon as the compartment returns to its normal storage temperature.

• The red food defrost alert light (for model FFM76) will also come on when the mains power is restored to warn there has been a power cut and the freezer compartment temperature has risen to an unsafe level allowing partial defrosting of stored food. If this light is ON, food should be either cooked and eaten within 24 hours, cooked and refrozen or thrown away. The red food defrost alert light is a particularly useful warning light if you were out at the time of the power cut. The light will remain on until cancelled. It can only be cancelled by pressing the button alongside it.

The bottom compartment drawer should be used to freeze fresh food. Transfer already frozen food to one of the upper drawers.

• Before loading 2kg or more of fresh food select fast freeze for the required pre-freeze time (see chart below).

• If freezing up to 2kg of fresh food just select fast freeze when loading.

Once the fresh food is loaded leave fast freeze on for 24 hours to freeze the food as quickly as possible.

The maximum freezing capacity for the HOTPOINT FFM76 in 24 hours is 12kg.

Note: Don’t forget to turn fast freeze off after 24 hours from the introduction of fresh food to be frozen. However fast freeze will turn off automatically after 48 hours if you do forget.

Pre-Freeze chart when selecting Fast Freeze:

Model	Load for freezing	Pre-freeze time	Load position
FFA76 / FFM76 / FFA75 / FFA74 / FFM74	8 to 12kg max.	24 hours	In the bottom drawer.
FFA76 / FFM76 / FFA75 / FFA74 / FFM74	6 to 8kg	12 hours	In the bottom drawer.
FFA76 / FFM76 / FFA75 / FFA74 / FFM74	2 to 6kg	6 hours	In the bottom drawer.
All	up to 2kg	not required	In the bottom drawer.

This feature allows you to set your fridge compartment to a warmer setting while you are away on holiday, to reduce running costs without affecting the freezer.

To set up holiday mode:

1. Remove any food, from the fridge compartment, that will deteriorate while you are away. Make sure the fridge is clean.

2. Close the door.

3. Press the holiday button and the amber holiday indicator light will show that holiday mode is set.

To reset to normal operation:

1. Press the holiday button OR open the fridge door. The amber holiday indicator light will go out to show holiday mode is cancelled.

2. The fridge compartment will return to the temperature set on the fridge temperature control wheel.

Note: Opening the door or pressing the holiday button at any time after holiday mode has been set will turn the function off. The holiday button works independently of the fridge temperature control wheel.

Note: Always use the handle provided to open the fridge / freezer door.

To ensure that your HOTPOINT FFM76 fridge freezer operates as efficiently as possible:

• Follow food packaging “best before/use by” instructions or your suppliers advice on a suitable maximum storage time.

• Keep foods tightly covered to retain moisture and prevent flavour/odour transference. Plastic bags, aluminium foil, plastic stretch wrap and containers with lids are ideal.

• Select chilled and frozen food last when shopping, transport in a ‘cool bag’ and place in freezer as soon as possible after arriving home.

• Avoid opening the doors unnecessarily or for longer than needed.

• Allow hot or warm food to cool down in covered containers before placing in the fridge or freezer, as placing hot food inside reduces efficiency.

• Prepare fresh foods for freezing in small quantities to ensure that the food freezes quickly and so that its quality does not deteriorate.

• Ensure that packets/containers of food are dry before freezing otherwise they may freeze together.

Storing Food in a Fridge

• Pack and store cooked and fresh food separately.

• Wrap raw or defrosting meat and poultry in polythene or foil and store below cooked foods and dairy products to avoid contamination of dripping food juices.

• Wrap cheese in greaseproof paper and place in an airtight container or polythene bag.

• Bring to room temperature before consuming.

• Empty left over canned food into a covered storage containers before placing in the fridge.

• Position food to allow cold air to circulate freely, ensuring nothing comes into contact with the back of the fridge compartment, or covers the defrost gutter drain hole below this.

• Use the different storage zones inside your fridge compartment to store a wide variety of food items.

STORAGE ZONES

Zone	Type	Food Storage
A	Cool	Dairy products, Cheese, butter, margarine, Low fat spreads, cooking fats / lards. Preserves – Jam, curd, marmalade, spread, salad dressing or sauces.
B	Colder	General food storage
C	Coldest	Meat fish & poultry. Pre-cooked / chilled food
D	Salad Bins	Vegetables, fruit and salad items (Not recommended for the storage of bananas or onions).

• Freeze and store either fresh food or long term commercially frozen foods.

• Generally speaking long term storage means up to 3 months but this can vary, so always follow your supplier’s recommendations otherwise refer to the pictorial guide on the door liner.

• Place frozen food in the freezer compartment as soon as possible after buying it.

• Liquid-filled bottles or sealed fizzy drinks must not be stored in freezer, as they may burst.

• Lollipops and water ices should not be given to children directly from the freezer the low temperature may cause ‘freezer burns’.

• Store ice cream towards the top front of the freezer and remove from freezer 15-30 minutes before serving.

• Ensure food is labelled and dated before placing in freezer.

• When freezing fresh food follow the instructions for using fast freeze (see CONTROLS section).

• Do not allow fresh food to come into contact with food already frozen, the frozen food could start to defrost.

• Once thawed, food should be cooked and eaten within 24 hours or cooked and refrozen.

STORAGE GUIDE FOR HOTPOINT FFM76

Frozen Food Storage Capacity	35kg
Maximum Freezing Capacity in 24 hours	12kg
Maximum Conservation Time from Failure	14 hours

The freezer compartments must be used with the drawers.

The storage drawers can be easily removed. Pull the drawer towards you until it reaches its stop position. Hold securely on both sides, lift the front of the drawer to release and remove. For cleaning advice see the CLEANING & MAINTENANCE section.

Ensure that the frozen food storage drawers are pushed back fully before closing the door.

Food can be separated into different storage drawers for easy identification.

When lifting or removing the large deep drawer it is important to hold the side handles and not the front handle.

WARNING: The freezer drawers can become heavy when fully loaded with food. Care must be taken if attempting to lift or carry a full freezer drawer. It is recommended to remove the required food, rather than the whole freezer drawer.

Note: It is important not to touch or move any of the freezer drawers/parts with wet hands as it may cause freezer burn or discomfort.

Fridge compartment – No manual defrosting required

The fridge compartment will defrost automatically. During defrost periods water droplets form on the interior back wall of your Fridge and refreeze afterwards.

WARNING: Ensure that stored food does not come into contact with the interior back wall of your Fridge. Also ensure the defrost gutter drain hole is kept clear.

Freezer compartment – Frost Free

The frost free system completely eliminates the need for defrosting. A fan circulates air around the freezer. This helps to remove moisture from the compartment, therefore preventing the build up of ice. It is normal to hear the fan when the freezer is cooling.

Additional benefits of the frost free system include:

• More even temperatures throughout the freezer.

• Faster cooling times.

WARNING: Switch off electrical supply and pull out mains plug before cleaning.

Interior

Note: We recommend you use a straw to keep the defrost gutter drain hole clear of any blockage. DO NOT use sharp metal tools which could cause damage beyond repair.

WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish to clean the interior, they will leave a smell in the fridge freezer.

1. Remove stored food, wrap or cover it and place into insulated containers to keep cool/frozen whilst cleaning.

2. Remove salad bins, racks, shelves and drawers from each compartment. Wash in warm water and washing up liquid using a soft cloth, dry thoroughly.

3. Wipe interiors and fittings with a clean cloth wrung out in a solution of either one teaspoon of bicarbonate of soda to one pint of water or a sterilising fluid, diluted according to the manufacturer’s instructions.

4. Dry interior compartments thoroughly with a clean cloth before replacing fittings and food.

Exterior

WARNING: Do not use abrasive powder, household cleaner or bleach, they can damage the exterior of your fridge freezer.

1. Use a clean soft cloth wrung out in warm water and washing up liquid to wipe the exterior surface, dry thoroughly.

2. Use a soft brush or vacuum cleaner to remove dust from underneath the fridge freezer and from the compressor and condenser situated at the back of the fridge freezer.

Door Seals

Use warm water and a clean soft cloth to wipe along and in between the creases of the door seals, dry thoroughly. Take care not to damage the seals and avoid using sharp objects.

WARNING: Do not use detergent, it will damage the seals.

If you are going away and don’t want to use your fridge freezer, switch off electricity supply and pull out the mains plug. Remove food and follow the cleaning instructions.

Note: Leave the doors ajar to prevent an accumulation of odours.

For the HOTPOINT FFM76, if you want to keep your freezer running but want to empty the fridge, you could set the holiday mode. See the CONTROLS section for details.

WARNING: Switch off electricity supply and pull out the mains plug.

Obtain a replacement SES 15 watt bulb and fit as follows:

1. Remove any shelves from directly below the interior light, to make access easier.

2. Squeeze the side of the lamp guard lightly to unclip. Remove and retain.

3. Remove old bulb and fit new one.

4. Refit lamp guard.

5. Plug in and switch on electrical supply.

WARNING: Switch off electrical supply and pull out the mains plug. Remove all door furniture and loose items from inside.

Remove Top Door

1. Open the door as wide as possible.

2. Support the door and using a screwdriver, remove the screw securing the top hinge.

3. Lower the top hinge and carefully tilt the door to remove the top hinge from the cabinet. Lift the door off the centre hinge.

4. Remove the top hinge from the door.

Remove Lower Door

5. Open the lower door and while supporting the door, remove the spacing washers and pin from the centre bracket. Note which way up the pin is fitted.

6. Lift the door off the bottom hinge.

7. Take the two screw covers off the centre hinge.

8. Unscrew the two screws to remove the centre hinge.

9. Remove any spacing washers fitted to the bottom hinge and store safely.

Reverse Hinges

10. Lay the appliance on its back on suitable packaging. Be careful that the appliance does not run away from you when the wheels touch the floor.

11. Unscrew the foot and hinge bracket from the bottom right. Unscrew the foot and footplate from the bottom left. Refit the hinge bracket and footplate to the opposite sides. Screw in the feet until there is approximately 35mm projecting from the bottom front edge. Lift the appliance onto its feet.

Refit Lower Door

17. Take off the two screw covers from the left hand centre panel and remove the two screws. Fit these screws and covers over on the right hand side.

18. Fit the centre hinge on the left hand side with the original screws, cover the screws with the original covers.

19. Using a thin blunt instrument, remove the hinge bush cap from the top left of the lower door and fit on the top right.

20. Place the lower door onto the lower hinge pin.

21. Offer the door up to the centre hinge. Put the hinge pin through the centre hinge and ensure it locates into the door. Check that the hinge pin is positioned the right way up.

Refit Top Door

22. Using a thin blunt instrument, remove the hinge bush cap from the top left of the door and refit on the top right.

23. Replace the spacing washers onto the centre hinge bracket.

24. Place the top door hinge onto the top left of the door, slide the door onto the centre hinge pin. Support the door while screwing the top hinge into position. Ensure that the hinge bracket locates correctly.

25. If necessary, slacken off the screws on the centre hinge pin and adjust the doors so that they line up with the cabinet.

26. Adjust the front feet.

Note: Let the appliance stand upright in its final location for at least 15 minutes before plugging in and switching on the electricity supply.

1. Check the plug is firmly positioned in the socket outlet and the power supply is switched on.

2. Check power supply with another appliance.

3. Check fuse/circuit breaker.

4. Check the door is closed properly.

1. Check that the rear pipe work is clear of the wall, skirting board and other obstacles.

2. Check that all feet/wheels are firmly in contact with the floor and the fridge freezer is level.

3. Refer to the ‘OPERATING SOUNDS OF A FRIDGE FREEZER’ section for normal operational noises.

1. Turn the control wheel to a higher number. See CONTROLS section.

2. If the fridge freezer is close to a heat source, move it to another location.

3. Check that there is enough ventilation around the fridge freezer.

4. Check that the doors have been closed properly.

Turn the control wheel to a lower number. See CONTROLS section.

1. Has the fridge freezer just been installed? If so, this is normal and the light will go out when the correct temperature has been reached.

2. Has the fridge freezer been loaded with a large quantity of food? If so, the light will go out when the correct temperature has been reached.

3. Have the doors been closed properly?

The food defrost alert only operates if a power cut has been long enough for the freezer to warm up and start defrosting the food. The freezer insulation will keep food frozen during a short power cut.

If you switch your freezer off and empty it or allow it to warm up, the food defrost alert light will come on when you turn the freezer on again. If there is no food inside to defrost press the button beside the light to cancel.

Fast freeze is selected. Remember to turn fast freeze off after 24 hours from the introduction of fresh food to be frozen. However, if you forget, it will automatically cancel after 48 hours.

Holiday mode is selected. Press the holiday button or open the fridge door to cancel this function and return the fridge freezer to normal operation.

The holiday mode setting can only be set when the door is closed. Opening the door or pressing any other button will turn holiday mode off. See the CONTROLS section for details on how to set the holiday mode.

A well sealed freezer door can be difficult to open. This is partly due to the difference in temperature between the room and internal freezer compartment. If you have just closed the freezer door, it maybe particularly difficult to open again immediately. Wait 5 minutes for the internal and external pressure to equalise and try again.

1. Check defrost gutter drain hole is not covered or blocked, see ‘Cleaning’ in the CLEANING & MAINTENANCE section.

2. Check that nothing has come into contact with the interior back wall of the fridge.

WARNING: Switch off the socket outlet and pull out the mains plug.

Check the bulb is screwed in correctly. If still not working then see ‘Changing the Light Bulb’ in the CLEANING & MAINTENANCE section.

1. Check that nothing is stopping the door from closing properly.

2. Check that foods and liquids are covered to avoid the build up of moisture inside.

3. If your kitchen becomes exceptionally warm, your fridge may not defrost regularly. Automatic defrosting will return to normal operation when the kitchen temperature cools.

You may notice the cabinet front is sometimes warm, this is normal and part of the refrigerant circulating system designed to help prevent condensation on the door seal.

WARNING: Do not open the freezer compartment door.

If power failure lasts longer than the maximum conservation time (14 hours for the HOTPOINT FFM76), frozen food will have started to defrost. The food defrost alert light will be lit when mains power is restored. This warning light indicates that stored food has started to defrost and should either be cooked and eaten within 24 hours, cooked and refrozen or thrown away.

These are the normal types of sound that your fridge freezer will make:

• The fridge freezer motor (compressor) makes a buzzing or humming sound when it is running. This can be louder when it is first switched on. This sound will reduce over the first few months.

• Gases flowing through the pipes can produce gurgling, bubbling, roaring or humming noises.

• Expansion and contraction of parts inside the fridge freezer can produce a cracking noise as they rapidly change temperature.

• The circulating fan in the freezer can make a whirring or buzzing sound as it blows cold air around the compartment.