Free English HOSMART HY812 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD HOSMART HY812 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I make a call using the HOSMART HY812?
To make a call, simply press the corresponding number channel button on the keypad of the HOSMART HY812.
How do I end a call on the HOSMART HY812?
To end a call on the HOSMART HY812, just press the End/Answer button once.
How do I use the monitor mode on the HOSMART HY812?
Press the MONITORED button to put the HOSMART HY812 in monitored mode. Press the MONITORED button then press the desired channel button. The HOSMART HY812 will then be monitored by the intercom corresponding to that channel for up to 24 hours. To exit monitor mode, press the End/Answer button.
How do I activate noisy mode on the HOSMART HY812?
To activate noisy mode on the HOSMART HY812, press and hold the NOISY MODE button for 3 seconds. You will hear a beep sound indicating that the intercom has entered noisy mode. Note that this action only activates noisy mode on the current HOSMART HY812 device and must be done when not in an ongoing call. It is recommended that all intercoms in the system are operated to enter noisy mode when one unit is in this mode.
How do I exit noisy mode on the HOSMART HY812?
To exit noisy mode on the HOSMART HY812, simply unplug the power cord and then plug it back in to power on the intercom. Upon powering on, the HOSMART HY812 will revert back to the regular mode.
How do I use the group call function on the HOSMART HY812?
Press the GROUP button on the HOSMART HY812 to call all connected intercoms. All intercoms will ring at the same time. Press the End/Answer button on any unit to answer the call, or press the button to exit the group mode. Note that while the Group button calls all units, it only allows talking to one unit; after one intercom picks up, the others cannot join the call.
How do I adjust the volume and ringtone on the HOSMART HY812?
You can press the VOL+ or VOL- buttons to adjust the volume of the HOSMART HY812. To change the ringtone, press and hold the VOL+ button for 3 seconds. You can then use the VOL+ and VOL- buttons to cycle through the 8 available melodies.
How do I assign a channel to my HOSMART HY812?
If you have purchased additional HOSMART HY812 units to expand your system, press and hold the desired number button on the intercom until you hear a beep sound, which indicates that the channel assignment is successful. It is not recommended to assign the same channel to multiple intercoms.
What is the recommended speaking distance for the HOSMART HY812?
The best speaking distance is about 30cm away from the MIC hole of the HOSMART HY812.
Troubleshooting: What should I do if the HOSMART HY812 will not power on?
Make sure the AC adapter and USB cable are connected properly to the HOSMART HY812.
Troubleshooting: What should I do if I cannot talk to other HOSMART HY812 intercoms?
Use the GROUP function to confirm whether the HOSMART HY812 cannot answer and make calls. Also, check the receiving distance between the intercoms to ensure they are not out of range.
Troubleshooting: What should I do if the sound on the HOSMART HY812 is too low?
Make sure the volume of the HOSMART HY812 has been increased enough and try to be closer to the MIC during the talk.
Troubleshooting: What should I do if the HOSMART HY812 is not getting the expected transmission range?
Keep the HOSMART HY812 away from metal objects and interference sources. Some electrical equipment will also interfere with the intercom to cause static, such as a microwave oven, router, cell phone, or other radio devices. Please try to adjust the position of the intercom.
Troubleshooting: What should I do if static or howling noise is heard from the HOSMART HY812?
The two intercoms may be too close, please try to move them away from each other.
How can I maintain the HOSMART HY812?
Keep the HOSMART HY812 stations from getting wet as they are not waterproof. Keep them in a controlled environment without extreme temperatures. Handle the stations with care, avoiding dropping, throwing, or roughness. Keep stations clean from dust and dirt to prevent damage to the circuit board. Do not use chemicals or cleaning solvents; simply use a damp cloth to clean the station.
CLICK HERE TO DOWNLOAD HOSMART HY812 (01) PDF DOCUMENT