HOOVER STEAMVAC V2 (01) PDF MANUAL

HOOVER STEAMVAC V2 (01) PDF SUMMARY:

What are the important safeguards to follow when using the deep cleaner?

• Use indoors only.
• Use only on surfaces moistened by the cleaning process. Do not immerse the product.
• Connect to a properly grounded outlet only.
• Do not clean over floor electrical outlets.
• Do not use without tanks in place.
• Use extra care when cleaning on stairs. Do not place deep cleaner on stairs.
• Use deep cleaner only for its intended use as described in the instructions.
• Use only attachments recommended by The Hoover Company; others may cause hazards.
• The use of an extension cord is not recommended. If an extension cord is absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-prong grounding type plug and a 3-pole receptacle that accepts the machine plug.
• Unplug deep cleaner when not in use. Turn off all controls before unplugging.
• Unplug before connecting the powered hand tool.
• Always disconnect cord from electrical outlet before servicing the deep cleaner.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Never handle plug or appliance with wet hands.
• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer.
• Close supervision is necessary when any appliance is used by or near children. Do not allow deep cleaner to be used as a toy or to run unattended at any time.
• Do not point tools toward people or pets.
• Use only commercially available Hoover SteamVac™ cleaners intended for machine application. Do not use any type of wax with deep cleaner.
• Keep detergents and other cleaners out of children’s reach.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
• Do not pick up chlorine bleach, drain cleaner, gasoline or any other toxic material with this appliance.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Avoid picking up hard, sharp objects with the deep cleaner. They may damage the machine.
• Keep hair, loose clothing, fingers, feet and all parts of body away from openings and moving parts.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• To help prevent matting and resoiling, avoid contact with carpets until they are dry. Keep children and pets away from carpets until they are completely dry.
• Store in a dry place. Do not expose machine to freezing temperatures.

---

What should I do if I’m unsure if the outlet is properly grounded?

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

---

What should I do if the plug provided with the appliance does not fit the outlet?

Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

---

Can a temporary adapter be used?

A temporary adapter may be used to connect this plug to a 2-pole receptacle if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.

---

How do I assemble the deep cleaner?

1. Attach hose/cord hook by inserting tabs on the hook into slots on back of cleaner and snap the hook onto the cleaner.
2. Slide tabs on the caddy into slots on back of cleaner.
3. Remove the clean water tank (upper tank) from deep cleaner.
4. With cord hook to back of deep cleaner, push upper handle down onto lower handle.
5. Push bolts into holes on front of handle. If bolts will not go through hole easily, the handle is not pushed completely down.
6. Place nuts in recessed areas on back of the handle. Hold each nut in place while tightening each bolt securely with a Phillips screwdriver.
7. Replace clean water tank (upper tank) by positioning the bottom first. Press the tank into place.
8. The hose/tool caddy can be used either on the cleaner for easy access to the tools and hose, or it can be removed and hung for storage. If you do not want to attach the caddy to the cleaner at this time, proceed to Fig. 1-10 for proper hose placement on the caddy.
9. Rotate top of caddy toward cleaner handle. Slide caddy down so notch on caddy rests in hook on cleaner.
10. Press hose, a few inches from nozzle connector end, into caddy. Bring hose up and over top of caddy.
11. Press hose into opposite side of caddy. Loop hose at bottom of cleaner and press into top of hook.
12. Loop hose over top of caddy again. Slide hose clip toward end of hose. Snap tab on hose connector into hose clip.
13. Insert top of bare floor tool through “loop” on caddy. Slide tool down into place.
14. Snap stair/upholstery nozzle onto caddy.
15. To remove the SpinScrub™ hand tool from the plastic bag, open the tool door.
16. Pull tool down and outward. To reposition the tool, reverse this procedure.
17. To reattach the tool cover, align hinges of cover with holes on sides of tool storage area. Snap door into place.

---

How do I store the hose and tools?

1. Press hose, a few inches from nozzle connector end, into caddy.
2. Bring hose up and over top of caddy.
3. Press hose into opposite side of caddy.
4. Loop hose at bottom of cleaner and press into top of hook.
5. Loop hose over top of caddy again.
6. Slide hose clip toward end of hose.
7. Snap tab on hose connector into hose clip.
8. Insert top of bare floor tool through “loop” on caddy. Slide tool down into place.
9. Snap stair/upholstery nozzle onto caddy.

---

How do I identify the hose parts?

• I. Nozzle connector end
• J. Solution tube

---

How do I operate the deep cleaner?

1. Plug deep cleaner into a properly grounded outlet.
2. To turn cleaner ON, push switch down.
3. To turn cleaner OFF, push switch up.
4. Step on pedal to lower handle to operating position.
5. To move your deep cleaner from room to room, put handle in upright and locked position, tilt deep cleaner back on wheels and push forward.

---

What is the function of the automatic shut-off?

When the recovery tank (lower tank) is full, the automatic shutoff mechanism will shut off the deep cleaner suction. The deep cleaner will no longer pick up dirty solution and the motor sound will become noticeably higher in pitch. When this happens, turn deep cleaner off and empty recovery tank before continuing use.

---

What are the brush setting options?

• ON – for cleaning of carpet and bare floors
• OFF – for cleaning carpets and bare floors when brushing is not desired Slide selector button to the desired setting before cleaning.

---

What are the tank functions?

• Clean water tank (upper tank) holds the water that will either be mixed with detergent for cleaning the carpet or floor, or used to rinse the carpet or floor.
• The detergent container is permanently attached to the water tank. It holds the detergent that mixes with the water.
• The recovery tank holds the dirty solution that is picked up from the surface being cleaned.

---

What are the Rinse Setting switch options?

• WASH-AutoRinse – This setting cleans your carpet with detergent and water on the forward stroke. On the reverse stroke, a water-only rinse is applied automatically.
• RINSE – This setting applies water-only rinse in both the forward and reverse strokes.

---

How do I fill the clean water tank?

1. Unplug deep cleaner from electrical outlet.
2. Place deep cleaner handle in the upright, locked position.
3. To remove tank, press down on tank handle and pull forward.
4. Fill tank (1 gallon) with hot tap water.
5. To fill detergent container (16 oz.), turn cap counterclockwise and remove cap.
6. Fill container with HOOVER Carpet/Upholstery Detergent or HOOVER Bare Floor Cleaner. Do not use Bare Floor Cleaner on carpet or upholstery. Do not use any type of wax with your ‘SteamVac’ deep cleaner. To assure proper results, use only HOOVER detergent.
7. Replace container cap and tighten.
8. Position bottom of tank onto cleaner and pivot tank to snap it into place.

---

How do I empty the recovery tank?

1. Turn deep cleaner off and unplug from electrical outlet.
2. To prevent possible leaking, remove clean water tank by pressing down on tank handle and pulling forward; set tank aside (do not set tank on furniture).
3. Step on handle release pedal and lower handle until it rests on the floor.
4. Turn recovery tank latches outward (one on each side of tank).
5. Raise handle straight up and lift tank off cleaner.
6. Carry tank to sink or drain.
7. Turn tank cap counterclockwise and remove cap.
8. Lower handle toward back of tank to unlock lid.
9. Lift lid off tank. Empty tank and reposition lid.
10. Raise tank handle to carrying position and place it onto deep cleaner.
11. Lower handle to front of tank.
12. Turn latches (one on each side of tank) inward to lock tank in place.

---

What should I do before I begin cleaning?

• Vacuum thoroughly.
• For upholstery, check cleaning code. Use your HOOVER ‘SteamVac’ deep cleaner only if the upholstery fabric is marked with a “W” (for “wet” clean) or “S/W” (for “solvent/dry” or “wet” clean). Do not clean fabric marked “S” (“solvent/dry” clean only). If your upholstery does not have a code, seek professional assistance.
• Test for colorfastness. Wet a white absorbent cloth with the detergent. In a small, hidden area, gently rub the surface with the dampened cloth. Wait ten minutes and check for color removal or bleed with white paper towel or cloth. If surface has more than one color, check all colors.
• When cleaning entire floor, move furniture out of area to be cleaned. For furniture too heavy to move, place aluminum foil or wax paper under legs. This will prevent wood finishes from staining carpet. Pin up furniture skirts and draperies.
• Pretreat spots and heavy traffic areas with HOOVER ® PreCleaner*. Test PreCleaner for colorfastness by first spraying it on a hidden area; wait ten minutes and blot with white paper towels or cloth. If no color change is visible, spray PreCleaner onto spots and traffic areas. Wait at least ten minutes. Use your ‘SteamVac’ deep cleaner to pick up PreCleaner and spot. Repeat until spot is removed; carefully scrub with a household scrub brush if necessary. Do not saturate carpet or upholstery with PreCleaner.
• To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray.
• To avoid wetting and possible damage to wood floors underneath area rugs/carpet, either move area rugs/carpet to a non-wood bare floor surface or place waterproof material underneath them before cleaning.

---

What should I do after cleaning?

• Allow carpet or upholstery to dry. To help prevent matting and resoiling the carpet, keep children and pets away from surface until it is completely dry. If it is necessary to walk on damp carpet, place towels or white cloths on the traffic areas. If furniture must be replaced before the carpet is dry, place plastic or aluminum foil under legs of furniture so metal slides or wood finishes will not stain the carpet.
• Empty tanks, rinse with clear water and let air dry. Rinse the recovery tank lid and let air dry. Any unused detergent may be left in the detergent container for future use.
• Remove lint from filter screen located inside recovery tank.
• Remove lint from filter screen located on bottom of cleaner as follows. Remove both tanks. Tilt cleaner back so handle rests on floor. Squeeze filter frame, lift and pull it out. Wipe off screen and push frame back into place. Return cleaner to upright position.
• If desired, vacuum thoroughly after carpet has completely dried. This will help reduce any shading left by the deep cleaner’s brushes.

---

How do I clean carpet?

1. Slide nozzle completely onto cleaner. Press down on nozzle to secure it.
2. Replace recovery tank.
3. Raise cleaner to upright position and replace clean water tank.
4. Fill clean water tank according to instructions.
5. Fill detergent container with HOOVER Carpet/Upholstery Detergent according to instructions.
6. Turn brushes ON or OFF as desired.
7. Dry hands and plug cord into a properly grounded outlet.
8. To avoid walking on damp carpet, start at the end of the room farthest from the door or path to sink where tanks will be emptied and filled.
9. Step on handle release pedal and lower handle to operating position.
10. Set Rinse Setting switch to WASH-AutoRinse.
11. Turn cleaner ON.
12. Squeeze trigger to release cleaning solution and slowly push deep cleaner forward (equals one wet stroke).
13. Continue to squeeze trigger and slowly pull deep cleaner back toward you (second wet stroke). The deep cleaner rinses the carpet on the backward pass. To assure proper rinsing, it is important to keep the deep cleaner on the same path backward as forward.
14. Release trigger and slowly push deep cleaner forward over area just sprayed with solution (dry stroke). Then slowly pull deep cleaner back toward you without squeezing trigger (dry stroke). Continue using dry strokes until little water is visible passing through the recovery tank lid.
15. For best results, use straight, parallel strokes. Overlap strokes by 1 inch to help prevent streaking.
16. Keep nozzle flat on floor for both forward and reverse strokes.
17. If you would like to rinse the carpet with water only, set Rinse Setting switch to RINSE. Repeat steps 7-9. In this setting, rinsing will be done on both forward and reverse strokes.
18. For heavily soiled areas, repeat steps 6-9. Avoid saturating carpet.
19. To avoid saturating carpet, do not use more than 4 wet strokes over one area. Always end with dry strokes. It is best to alternate wet and dry strokes.
20. For best cleaning results and to aid in faster drying of carpet, end with more dry strokes.
21. Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction.

---

How do I remove the nozzle?

1. Unplug deep cleaner from electrical outlet.
2. Remove both tanks.
3. With handle in upright position, tilt cleaner back so that handle rests on the floor.
4. Lift up rear edge of nozzle.
5. Slide nozzle up and remove from cleaner.

---

How do I replace the nozzle?

1. Line up tabs on nozzle with holes in cleaner.
2. Slide tabs into holes.

---

How do I clean the nozzle?

If lint or other debris becomes lodged in nozzle, it can be removed for cleaning.

---

How do I attach the bare floor attachment?

1. Unplug deep cleaner from electrical outlet.
2. Remove clean water tank and recovery tank before positioning bare floor attachment.
3. With handle in upright position, tilt cleaner back so that handle rests on the floor.
4. With foam strip in position, place attachment on front of nozzle. Make sure arrow on end of attachment points in the direction as shown.
5. Push attachment against nozzle while rotating attachment downward until both ends snap into place.
6. Return deep cleaner to upright position. Lower handle and replace recovery tank.
7. Raise handle to upright position and reposition clean water tank.

---

How do I clean bare floors?

1. Fill clean water tank according to instructions.
2. Fill detergent container with HOOVER Bare Floor Cleaner according to instructions.
3. Turn brushes ON for scrubbing or OFF if scrubbing is not desired.
4. Dry hands and plug deep cleaner into a properly grounded outlet.
5. Step on handle release pedal and lower handle to operating position.
6. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.
7. To release solution, press trigger. Slowly move deep cleaner forward and backward over area to be cleaned. Water and detergent will be released on the forward stroke. A water-only rinse will automatically be released on the reverse stroke.
8. To pick up dirty solution, release trigger and slowly move deep cleaner over area where solution has just been dispersed. Use both forward and reverse strokes.
9. If rinsing the floor is desired, set Rinse Setting switch to RINSE. Repeat steps 7 & 8. This setting provides a water-only rinse in both the forward and reverse strokes. Rinsing is not necessary, but will help remove detergent residue from the floor.
10. Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction.
11. When finished cleaning, follow “After cleaning” instructions.
12. Unplug deep cleaner from electrical outlet and remove attachment from nozzle.
13. Rinse the attachment in clear water. Do not remove plastic screen or foam from attachment.

---

How do I attach the hose?

1. Unplug cleaner from electrical outlet.
2. Open hose connection port.
3. Insert short hose end, matching tabs on hose with same-sized slots in port.
4. Plug solution tube firmly into solution connection port.

---

How do I drain the solution tube?

Drain the solution tube by placing round end in sink and raising nozzle above your head. Press the trigger.

---

How do I drain the suction hose?

Drain the suction hose by turning deep cleaner ON and holding nozzle up for several minutes. Do not press trigger.

---

How do I disconnect the hose and solution tube from deep cleaner?

Unplug deep cleaner from electrical outlet. Disconnect hose and solution tube from deep cleaner.

---

How do I attach tools to the hose?

1. Place handle in upright position and remove hose from rack.
2. Connect tool to hose by sliding it onto connector until the tab locks it securely.
3. Using your thumb, push forward and up on the latch to remove tool.

---

What tools might be included?

• SpinScrub™ hand tool has rotating brushes for extra scrubbing action on small carpet areas, carpeted stairs and upholstery. For some models, the brushes can be removed for converting to the scrub module.
• Stair/upholstery nozzle has a built-in brush to help provide the scrubbing action some spots may need for removal.
• Scrub module with detachable scrub pad attaches to the base of the SpinScrub™ hand tool (in place of brush module). Can be used to scrub stubborn areas such as scuff marks, dried spills, and in hard to reach areas on hard surfaces.
• Crevice tool can be used to clean along edges of carpet, carpeted stairs and on upholstery.

---

How do I attach the scrub module?

1. Open the tool door and remove the SpinScrub™ hand tool.
2. Grasp the sides of the brush module and lift it from the base.
3. Snap scrub module onto the base. It may be necessary to rotate the scrub module slightly so it will align properly to the base.

---

How do I use the scrub tool?

1. Attach hose and solution tube.
2. Place handle in upright position.
3. Fill clean water tank according to instructions.
4. Fill detergent container with HOOVER Bare Floor Cleaner according to instructions.
5. Attach tool to end of hose.
6. Hold scrub tool above area to be cleaned and press trigger to dispense solution.
7. Release trigger and scrub area with tool. Pick up dirty solution with squeegee.

---

How do I clean the scrub pad after use?

Pull it off module. Wash it in water with mild detergent. Rinse and let air dry. Pad must be completely dry before reattaching to module.

---

How do I clean carpeted stairs?

1. Attach hose and solution tube.
2. Place handle in upright position.
3. Fill clean water tank according to instructions.
4. Fill detergent container with HOOVER Carpet/Upholstery Detergent according to instructions.
5. Attach tool to end of hose.
6. Hose length may require that machine be placed at the top of the stairs to clean upper half of stairway and at bottom of stairs to clean lower half. To prevent machine from falling, use extra caution when cleaning on stairs. Do not place deep cleaner on stairs. Do not point tools toward people or pets.
7. Dry hands and plug deep cleaner into a properly grounded outlet.
8. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.
9. Pre-spray the carpeted stair by holding the tool about one inch above the carpet and push it forward while pressing the trigger (equals one wet stroke).
10. Position tool against the riser and slightly press it into carpet pile. Press the trigger and pull the tool slowly over the carpet (second wet stroke). Release trigger at end of stroke.
11. Lift tool, and position it against riser. Pull tool slowly over carpet without pressing trigger (dry stroke).
12. Overlap strokes by 1/2 inch to help prevent streaking. It is best to alternate wet and dry strokes. End with more dry strokes to aid in faster drying of carpet.
13. To avoid saturating carpet, do not use more than 4 wet strokes over any one area. Always end with dry strokes.
14. Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction.

---

How do I clean upholstery?

1. Attach hose and solution tube.
2. Place handle in upright position.
3. Fill clean water tank according to instructions.
4. Fill detergent container with HOOVER Carpet/Upholstery Detergent according to instructions.
5. Attach tool to end of hose.
6. Dry hands and plug deep cleaner into a properly grounded outlet.
7. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.
8. Gently press the tool onto the fabric. Press the trigger and slowly pull the nozzle over the fabric.
9. Overlap strokes by 1/2 inch to help prevent streaking. Make additional strokes without pressing the trigger to remove more moisture.
10. To clean in corners or creases, lift the tool one-half inch from the fabric and press the solution trigger.
11. Vacuum up the solution with the tool without pressing the trigger.
12. For heavily soiled areas, it may be necessary to repeat the cleaning process. Make crisscrossing strokes to the original pattern; overlap each pass.
13. Make no more than 2 passes with the solution or rinse over any one area to prevent over-wetting and damage to fabric.
14. Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction.

---

How do I remove the brushes for cleaning?

1. Disconnect cleaner from electrical outlet.
2. Remove clean water tank and recovery tank.
3. Grab brush assembly and pull firmly.

---

How do I replace the brushes?

1. Align posts on both ends of brush assembly with slots in cleaner housing.
2. Make sure that the square post also aligns with the square hole.
3. Turn brushes slightly until post fits easily into hole.
4. Press brush assembly firmly to snap into place.

---

What should I do before storing the deep cleaner?

• Empty clean water tank and let air dry.
• Unused detergent can be stored in the detergent container.
• Empty recovery tank, rinse tank and lid thoroughly with clean water and let air dry.
• Allow brushes and underside of deep cleaner to air dry thoroughly before storing deep cleaner on a carpeted or wood surface.
• Do not store deep cleaner with a full clean water tank in place.

---

What are some possible reasons the machine won’t run?

Possible Cause	Possible Solution
Not firmly plugged in	Plug unit in firmly
No voltage in wall receptacle	Check fuse or breaker
Blown fuse/tripped breaker	Replace fuse/reset breaker

---

What are some possible reasons for low solution pick-up?

Possible Cause	Possible Solution
Recovery tank full/automatic shut off engaged	Remove and empty recovery tank
Blockage in tool on end of hose	Remove tool and clear blockage
Recovery tank lid not on correctly	Make sure lid is on securely
Water tank empty, but detergent remains	Fill water tank
Clean water tank not firmly in place	Make sure tank is securely locked in position
Clean water tank or detergent container empty	Refill container according to instructions for surface being cleaned
Recovery tank lid not on correctly	Make sure lid is firmly in place

---

What are some possible reasons the clean solution won’t dispense?

Possible Cause	Possible Solution
Recovery tank full/automatic shut off	Remove and empty recovery tank

---

What are some possible reasons the brushes won’t rotate during floor cleaning?

Possible Cause	Possible Solution
Dirty filter screen on bottom of unit	Clean screen as shown in Fig. 3-2
Setting selector on OFF	Move setting selector to ON