HONEYWELL HY-105 (01) PDF Document

To reduce the risk of shock, the HONEYWELL HY-105 has a polarized plug (one blade is wider than the other). This plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.

Additionally, observe the following:

1. Do not operate the fan with a damaged cord or plug or if the product malfunctions, is dropped, or damaged in any manner.

2. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlets.

3. Do not run the fan cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from traffic areas and where it will not be tripped over.

4. To disconnect the fan, first turn the unit OFF, grip the plug and pull it from the wall outlet. Never pull the plug by the cord.

The HONEYWELL HY-105 features a fused safety plug designed to cut off electric current if an electrical fault occurs. If your fan loses power and you suspect the fuse has blown, follow these User Servicing Instructions:

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.

2. Locate the spare fuse holder attached to the cord plug. Remove the spare fuse from the plastic spare fuse holder and set it aside.

3. Gain access to the blown fuse by sliding open the door found on the side of the plug. Slide the door outward until the blown fuse is fully visible.

4. Carefully remove the blown fuse and snap the replacement fuse into place.

5. Risk of fire: Replace the fuse only with a 2.5 Amp, 125 volt fuse (provided with the product).

6. Fully close the fuse door by sliding it back into place. Discard the blown fuse. The plug should now be ready for normal use.

Note: Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Pedestal Assembly: Line up the left and right pedestal assembly and firmly snap them together.

Base Assembly: Align the two portions of the circular base and snap them together by gently pushing the 4 extrusions into the adjacent circles of the connecting piece.

Securing the Pedestal to the Base:

1. Align the 3 screw holes on the bottom of the pedestal with the 3 holes in the base such that the power cord holder is at the rear of the unit.

2. Secure the base assembly to the pedestal by inserting and tightening the 3 screws in the 3 holes located on the bottom of the base.

1. Carefully turn the fan on its side and place it on a table. Place the power cord through the center of the pedestal and base assembly.

2. Align the pedestal with the tower fan so that the one locking screw hole on the pedestal body is aligned with the rear of the tower fan unit.

3. Firmly hold the base steady and rotate the pedestal assembly clockwise to lock the tower fan to the pedestal assembly.

4. Secure the pedestal to the tower fan by inserting and tightening 1 screw in the opening located near the top rear of the pedestal assembly.

1. With the fan still on its side, locate the cord holding bracket on the bottom of the base.

2. Gently pull any slack out of the power cord, place the power cord securely in the holding bracket, and secure the power cord bracket over the power cord.

3. Return the tower fan to its upright position.

Note: Do not operate the tower fan unless it is in its proper, upright position.

1. Remove the battery door by sliding it downward in the direction of the arrow.

2. Insert 2 AAA batteries into the remote following the directional guides in the recessed slots.

3. Replace the battery door by sliding it upward opposite of the arrow direction until the door snaps in place.

Note: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

On/Off: To turn the fan on, press the Power button located on the left side of the control panel. Press the Power button a second time to turn the fan off.

Speed Control: The fan will automatically start on “Sleep” speed when initially turned on. To adjust the speed up or down, press the Fan Speed button repeatedly to increase the level.

Oscillation: To activate the Oscillation feature, press the Oscillation button once. Press the Oscillation button again to turn the Oscillation feature off.

Timer: Choose from 1, 2, 4, or 8 hour settings by performing the following function:

• 1 hour: Press the Timer button once.

• 2 hours: Press the Timer button twice.

• 4 hours: Press the Timer button a third time.

• 8 hours: Press the Timer button a fourth time.

Press the Timer button a fifth time to turn the Timer feature off.

For units equipped with Temperature Control:

1. Press and hold the Temperature Control Button to enter temperature mode.

2. The current room temperature is displayed for 3 seconds, then the display begins to flash at 1-second intervals. If a temperature is not selected, the unit will revert back to “speed mode” after 10 seconds.

3. Press the temperature button repeatedly to increase the temperature by one-degree intervals starting from room temperature. You will have to cycle through 90° to get back to the 60° point (this is the minimum). For Canada models, the range is 15°C to 30°C.

4. Once the desired temperature is selected, the fan will revert back to the room temperature display.

Note: The fan speed will adjust automatically to achieve the desired temperature. The fan will stop if the room temperature drops below the setpoint and will turn on again if the room temperature climbs above the setpoint.

Yes, in the following ways:

• If the user hits the “Power” button, this will override all functions and the unit will shut “OFF”. The temperature setting will be cleared.

• If the user hits the “speed” button, this will also override temperature mode.

However, if the Timer button is selected, the temperature will not be affected; the chosen temperature will remain in effect and the room temperature will continue to be displayed. The Timer will function with or without Temperature Mode. Additionally, if the oscillation button is selected, the Temperature Mode will not be affected.