HONDA FURY 2024 (01) PDF Document

To enhance your safety when operating the HONDA FURY 2024, follow these guidelines:

Perform all routine and regular inspections specified in the manual.

Stop the engine and keep sparks and flames away before filling the fuel tank.

Do not run the engine in enclosed or partly enclosed areas as carbon monoxide in exhaust gases is toxic and can be fatal.

Always wear an approved helmet and protective apparel to significantly reduce the risk and severity of head and other injuries.

If you are not equipped with the optional passenger seat kit, never carry a passenger as the vehicle was not designed for one without proper equipment.

If equipped with the optional passenger seat kit, ensure both you and your passenger wear approved helmets and protective gear. Instruct the passenger on how to hold onto the seat strap or your waist and how to lean with you during turns.

Always ride defensively and do not assume other drivers see you. Be prepared to stop quickly or perform an evasive maneuver.

Ride within your personal limits and never faster than conditions warrant. Fatigue and inattention can impair your judgment.

To adjust the 24-hour display clock on your HONDA FURY 2024, follow these steps:

1. Turn the ignition switch to the ON position.

2. Use the select/reset button to select the clock display.

3. Press and hold the select/reset button until the hour digits start flashing.

4. Press the select/reset button until the desired hour is displayed.

5. Press and hold the select/reset button. The minute digits will start flashing.

6. Press the select/reset button until the desired minute is displayed.

7. Press and hold the select/reset button until the display stops flashing to finish the setup.

Note: The adjustment will be cancelled if the button is not pressed for about 30 seconds, or you can finish by turning the ignition switch OFF.

The HONDA FURY 2024 features several warning and status indicators:

ABS (Anti-lock Brake System) indicator: Comes on when the ignition is ON and goes off when speed reaches approximately 6 mph (10 km/h). If it comes on while riding, there may be a problem with the system.

Low oil pressure indicator: Comes on when the ignition is ON and goes off when the engine starts. If it comes on while the engine is running, pull over safely and stop the engine immediately.

High coolant temperature indicator: If this indicator comes on while riding, the engine is overheating. Pull over and allow it to cool.

Low fuel indicator: Comes on when there is only approximately 0.66 US gal (2.5 L) of reserve fuel left in the tank. Refuel as soon as possible to avoid damaging the catalytic converter.

PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL): Comes on briefly when the ignition is turned ON. If it comes on while the engine is running, have the vehicle inspected by a dealer.

Neutral indicator: Comes on when the transmission is in Neutral.

High beam indicator: Comes on when the headlight high beam is in use.

Turn signal indicators: Flashing indicates the left or right turn signals are active.

To start the engine of the HONDA FURY 2024, regardless of whether it is cold or warm, use the following procedure:

1. Make sure the engine stop switch is in the Run position.

2. Turn the ignition switch to the ON position.

3. Shift the transmission to Neutral (the N indicator should come on). Alternatively, you can pull in the clutch lever to start the vehicle in gear if the side stand is raised.

4. Press the start button with the throttle completely closed.

5. If the engine does not start within 5 seconds, turn the ignition to OFF and wait 10 seconds before trying again to recover battery voltage.

6. If the engine fails to start using the normal procedure, open the throttle fully and press the start button for 5 seconds, then repeat the normal starting procedure.

The HONDA FURY 2024 transmission has 5 forward gears in a one-down, four-up shift pattern. Recommended speeds for shifting are as follows:

When refueling the HONDA FURY 2024, adhere to these specifications:

Fuel Type: Use unleaded gasoline only.

Recommended Fuel Octane Number: Pump Octane Number (PON) 86 or higher.

Tank Capacity: 3.38 US gal (12.8 L).

Filling Level: Do not fill with fuel above the lower edge of the filler neck.

Opening the cap: Open the lock cover, insert the ignition key, and turn it clockwise to remove the cap.

Closing the cap: Align the latch with the slot in the filler neck, push the cap until it snaps closed and locks, then remove the key and close the lock cover. The key cannot be removed if the cap is not locked.

During the first 300 miles (500 km) of operation, follow these guidelines to ensure the future reliability and performance of your HONDA FURY 2024:

Avoid full-throttle starts and rapid acceleration.

Avoid hard braking and rapid down-shifts.

Ride conservatively to allow components to seat properly.

To ensure safety, check the following items before every ride on your HONDA FURY 2024:

Tires: Check air pressure and examine the tread for wear or damage.

Lights, horn, and turn signals: Ensure they are all operating normally.

Fluid levels: Check the engine oil, engine coolant, final drive oil, and brake fluid levels.

Throttle: Ensure the action is smooth without binding in all steering positions.

Brakes: Check that the brake lever and pedal operate normally.

Engine stop switch: Verify that it functions properly.

Side stand: Ensure it functions properly and the engine cut-off system works when shifted into gear with the stand down.

Routine maintenance should be performed at the following odometer intervals (whichever comes first):

To check the engine oil level on your HONDA FURY 2024:

1. If the engine is cold, idle it for 3 to 5 minutes.

2. Turn the ignition OFF and wait 2 to 3 minutes.

3. Place the vehicle in an upright position on a firm, level surface.

4. Remove the oil fill cap/dipstick and wipe it clean.

5. Insert the dipstick until it seats, but do not screw it in.

6. Verify the level is between the upper and lower marks. If it is near the lower mark, add the recommended oil (SAE 10W-30, JASO T 903 standard MA) until it reaches the upper mark.

7. Reinstall the dipstick securely. Do not overfill.

The HONDA FURY 2024 allows for adjustments to both spring preload and rebound damping:

Spring Preload: Remove the right side cover. Turn the adjuster knob clockwise to increase preload (harder) or counterclockwise to decrease it (softer). The standard position is 6 clicks from the minimum setting.

Rebound Damping: Turn the damping adjuster clockwise to increase damping (hard) or counterclockwise to decrease it (soft). The standard position is 3/4 turns from the maximum setting, aligning the punch mark on the adjuster with the reference punch mark.

Note: The rear shock absorber contains high-pressure nitrogen gas. Do not attempt to disassemble or service the unit yourself.

If the high coolant temperature indicator comes on or acceleration becomes sluggish on your HONDA FURY 2024, follow this procedure:

1. Pull safely to the side of the road and stop the engine using the ignition switch. Turn the ignition back to the ON position.

2. Check if the radiator fan is operating. If the fan is not operating, do not start the engine and contact a dealer.

3. If the fan is operating, allow the engine to cool with the ignition switch OFF.

4. Once cooled, check the radiator hose for leaks and check the coolant level in the reserve tank. Add coolant if necessary.

5. If the level is normal and no leaks are found, you may continue riding, but monitor the temperature indicator closely.

If the starter motor fails to operate on the HONDA FURY 2024, check the following items:

Check the engine starting sequence (Neutral position, ignition ON, stop switch in Run).

Check for a blown fuse, specifically the main fuse or the starter fuse.

Check for a loose battery connection or terminal corrosion.

Check the condition of the battery to see if it has been drained.

If the problem persists, the vehicle should be inspected by a qualified dealer.

The electrical system specifications for the HONDA FURY 2024 are as follows:

Battery: YTZ14S (12 V-11.2 Ah 10 HR).

Main Fuse: 30 A.

Other Fuses: 30 A, 20 A, 10 A.

Note: Always replace a blown fuse with one of the same rating. Using a fuse with a higher rating can cause damage to the electrical system.

If you experience a minor puncture on the HONDA FURY 2024, you can make an emergency repair using a tubeless tire repair kit. Follow these safety precautions:

Always have the tire inspected or replaced by a dealer as soon as possible after an emergency repair.

Riding with a temporary repair is risky. Do not exceed 30 mph (50 km/h).

Ride slowly and carefully until the tire is replaced.

Ensure the replacement tire is the correct size and type: Front 90/90-21M/C 54H; Rear 200/50R18M/C 76H.