HONDA ACCORD SEDAN 1993 (01) PDF Document

During the first 600 miles (1,000 km) of driving your HONDA ACCORD SEDAN 1993, avoid full throttle starts and cruising for extended periods at a constant speed. This procedure also applies to exchanged or overhauled engines. During and after this period, drive the car at moderate speeds until the engine is fully warmed up. Additionally, try to avoid severe braking during the first 200 miles (300 km) to maintain future braking efficiency.

The HONDA ACCORD SEDAN 1993 is supplied with two types of keys:

Master Key: Fits the ignition and all locks on the vehicle.

Valet Key: Fits the ignition and doors, but it will not work for the trunk, trunk remote release, rear seat trunk access, or the glove box. This key is intended for use when leaving the car with a parking attendant or repair person while keeping valuables locked away.

In the HONDA ACCORD SEDAN 1993, you can lock the doors by pushing the plunger down. The doors must be unlocked before they can be opened. Passenger doors can be locked while open and will stay locked when closed. However, the driver’s door cannot be locked while open unless the door handle is held open. Front doors can also be locked and unlocked from the outside using the key.

On equipped models of the HONDA ACCORD SEDAN 1993, all doors can be simultaneously locked and unlocked by operating the master door lock switch located on each front door. Additionally, the passenger doors will lock automatically when the plunger on the driver’s door is pushed down or when the driver’s door is locked from the outside with the key.

The trunk of the HONDA ACCORD SEDAN 1993 can be opened from inside by pulling up the lever located at the left side of the driver’s seat. To open it from the outside, insert the master key and turn it clockwise. The internal trunk lid opener lever can also be locked using the master key to prevent unauthorized access.

The HONDA ACCORD SEDAN 1993 features child proof door locks on the rear doors to prevent accidental opening. To activate them, push down the lock tabs located on the edge of each rear door and then close the doors. When activated, the rear doors can only be opened from the outside.

To adjust the seat position in the HONDA ACCORD SEDAN 1993, pull up on the adjustment lever under the front edge of the seat cushion and slide the seat to the desired position. Release the lever and ensure the seat is locked by moving it back and forth. To change the seat-back angle, pull up on the lever at the outside edge of the seat, lean to the desired angle, and release the lever to lock it in place.

For the HONDA ACCORD SEDAN 1993, follow these safety guidelines:

1. Do not adjust the driver’s seat while the car is moving, as it could cause loss of vehicle control.

2. To reduce the risk of sliding under seat belts in a collision, keep seat-backs in an upright position while driving.

3. Always sit well back in the seat for maximum seat belt effectiveness.

The head restraints in the HONDA ACCORD SEDAN 1993 can be adjusted for height by pulling them up. To lower them, slide the button next to the restraint’s height bar while pushing the restraint down. They should be adjusted so the top of the restraint is approximately level with the tops of your ears. Never drive the car with head restraints removed and do not try to adjust them while driving.

On equipped models of the HONDA ACCORD SEDAN 1993:

Lumbar Support: Adjust the lower back support by turning the knob on the driver’s armrest.

Driver’s Center Armrest: The angle can be adjusted to five positions. To lower it, push the button on the driver’s side of the armrest.

Rear Seat Armrest: Located at the center of the rear seat-back, it can be used by pulling the tab out.

Note: Never adjust these items while driving.

In the HONDA ACCORD SEDAN 1993, the rear seat-back can be released by turning the lock on the rear shelf with the master key and pulling the top of the seat-back down. It can also be released from inside the trunk by pulling the release cord. This allows the transport of long objects. When closing, push the seat-back firmly into place and ensure it is secure.

When carrying items in the HONDA ACCORD SEDAN 1993, adhere to the following:

1. Secure all luggage or cargo within the trunk.

2. Do not store items on the shelf behind the rear seat as they can become dangerous projectiles in a crash.

3. Do not exceed the weight limits shown on the label on the driver’s door jamb.

4. If carrying items in the cabin, use the floor space between the front and rear seats.

5. Ensure rear shoulder belts are positioned in front of the seat-backs when they are upright.

The HONDA ACCORD SEDAN 1993 is equipped with lap/shoulder belts in the front seats and outside rear positions, and a lap belt in the center rear position. Lap/shoulder belts feature emergency locking retractors that allow freedom of movement during normal driving but lock automatically during a collision or sudden stop. A reminder light and beeper on the instrument panel activate if the driver’s seat belt is not fastened when the ignition is turned on.

To wear the belt in the HONDA ACCORD SEDAN 1993:

1. Pull the latch plate across your body and insert it into the buckle until it locks.

2. Ensure the belt is not twisted.

3. Position the lap portion as low as possible across your hips, not your stomach.

4. Pull up on the shoulder part to remove slack, ensuring it goes over your collarbone and across your chest.

5. If the belt crosses your neck, adjust the belt anchor height (front seats have four positions) or move toward the center of the seat (rear seat).

To use the lap belt in the HONDA ACCORD SEDAN 1993, pull the latch plate across your hips and insert it into the buckle marked CENTER. If the belt is too short, hold the latch plate at a right angle and pull to extend it. Position the belt as low as possible across your hips and pelvic bones, and pull the loose end for a snug, comfortable fit. To unlatch, push the red PRESS button on the buckle.

A pregnant woman should always wear a properly positioned seat belt in the HONDA ACCORD SEDAN 1993. It is recommended to use a lap/shoulder belt with the lap portion positioned as low as possible across the hips. Consult a doctor during check-ups to confirm it is okay to drive and to discuss proper belt positioning.

Check the condition of the belts in your HONDA ACCORD SEDAN 1993 regularly. Look for frays, cuts, burns, or wear. Ensure latches work smoothly and belts retract easily. Clean dirty belts with a soft brush and a mixture of mild soap and warm water. Do not use bleach, dye, or cleaning solvents. If belts retract slowly due to dirt build-up in the metal loops, wipe the inside of the loops with a clean cloth dampened in isopropyl alcohol.

The SRS in the HONDA ACCORD SEDAN 1993 includes a driver’s airbag in the steering wheel, and on the SE model, a front passenger’s airbag in the dashboard. The system also contains a diagnostic unit that monitors sensors and wiring when the ignition is ON, an SRS indicator light on the dash, and an emergency power backup system. Airbags are designed to inflate only in severe frontal collisions.

Have the HONDA ACCORD SEDAN 1993 system checked if the SRS light does not come on when the ignition is turned to ON (II), if the light stays on after the engine starts, or if it comes on or flashes while you are driving. The light normally comes on for about six seconds when the key is first turned to the II position.

When the HONDA ACCORD SEDAN 1993 is ten years old, the Supplemental Restraint System must be inspected by an authorized dealer. The production date of the vehicle is located on the left rear door jamb for reference.

According to safety statistics, children of all sizes are safer in the rear seat of the HONDA ACCORD SEDAN 1993. It is recommended to secure infant or toddler seats in the center position of the rear seat using the lap belt. For children who have outgrown child seats, the outside positions of the rear seat using lap/shoulder belts are recommended. Never put an infant seat in the front passenger seat if the car is equipped with a passenger airbag.

Infants up to 20 pounds (9 kg) must be restrained in a rear facing infant seat or convertible seat in the HONDA ACCORD SEDAN 1993. It is best placed in the center rear seat. If used in another position with a lap/shoulder belt, a locking clip must be installed on the belt.

To install a locking clip in the HONDA ACCORD SEDAN 1993:

1. Route the lap/shoulder belt through the child seat according to the maker’s instructions.

2. Insert the latch plate into the buckle and pull the shoulder part to remove slack.

3. Tightly grasp the belt near the latch plate and pinch both parts together.

4. Unbuckle the belt and install the locking clip as close to the latch plate as possible.

5. Re-insert the latch plate into the buckle and check that the seat is held firmly.

The ABS in the HONDA ACCORD SEDAN 1993 helps maintain steering control by preventing wheel lock-up during braking. The system is always ON and may cause a pulsation in the brake pedal when activated. You should continue to press the brake pedal with consistent force. If the ABS indicator light on the dash stays on, the anti-lock function has shut down, and the brakes will function as a conventional system.

The fuel tank capacity for the HONDA ACCORD SEDAN 1993 is approximately 17.04 US gallons (64.5 liters, 14.19 Imperial gallons). When the needle on the fuel gauge first indicates E (Empty), there is a usable reserve of approximately 1.1 US gallons (4 liters) left in the tank.

If the needle reaches the red line at H (Hot) in the HONDA ACCORD SEDAN 1993, pull safely off the road and stop the engine. Wait until the engine is cool before checking the coolant level in the reserve tank. Never remove the radiator cap when the engine is hot, as the coolant is under pressure and can cause severe burns.

If the D4 indicator light flashes while driving in any gear range in the HONDA ACCORD SEDAN 1993, it indicates a possible malfunction in the transmission. You should avoid rapid acceleration and have the vehicle checked by an authorized dealer as soon as possible.

If the charging system light comes on while driving the HONDA ACCORD SEDAN 1993, stop the car and turn off the engine. Check the belt tension by pushing with about 22 lbs (98 N) of force on the middle of the belt. The belt should deflect approximately 0.4 to 0.5 inches (10 to 12 mm). If the engine has been running, be careful as components may be hot.

The HONDA ACCORD SEDAN 1993 features an indicator that changes from green to yellow, and then to red, as you approach the 7,500-mile (12,000 km) maintenance interval for oil and filter changes. To reset the indicator after service, insert the ignition key into the slot below the tachometer. The color will change back to green.

To adjust the steering wheel position in the HONDA ACCORD SEDAN 1993, push the lever under the dash on the left side of the steering column all the way down. Move the steering wheel to the desired position, then pull the lever up to lock it. Do not adjust the steering wheel while the car is moving, and ensure it is locked by rocking it slightly after adjustment.

The windshield washer reservoir for the HONDA ACCORD SEDAN 1993 has the following capacities:

US Cars: 2.6 US quarts (2.5 liters, 2.2 Imperial quarts).

Canada Cars: 4.8 US quarts (4.5 liters, 4.0 Imperial quarts).

Always use a good quality commercial washer fluid. Do not use radiator antifreeze or vinegar/water combinations as they can damage paint or the pump.

For the HONDA ACCORD SEDAN 1993:

Rearview Mirror: Use the tab at the bottom to switch between day and night positions to reduce glare.

Manual Outside Mirrors: Use the knob on each door to adjust the angle.

Power Outside Mirrors: With the ignition in the II position, move the main switch to L or R, then use the adjustment switch. Return the main switch to the center position after adjustment.

In the HONDA ACCORD SEDAN 1993, the left-side lever controls lights. Rotate the switch to the first position for parking lights and the second for headlights. Push the lever forward for high beams (blue indicator light on dash) and pull it back for low beams. To flash headlights, pull the lever lightly. Push the lever down for left turns and up for right turns. A chime will sound if you open the driver’s door with the light switch on.

To use cruise control in the HONDA ACCORD SEDAN 1993:

1. Push the master switch to the left of the steering column (indicator will light).

2. Accelerate to above 25 mph (40 km/h).

3. Press and hold the SET/decel button on the steering wheel until the cruise indicator on the dash lights.

4. To increase speed, press and hold RESUME/accel. To decrease, press and hold SET/decel.

5. To cancel, tap the brake or clutch pedal, or press SET and RESUME simultaneously, or turn off the master switch.

Hood: Pull the handle under the left side of the dash. From the front of the HONDA ACCORD SEDAN 1993, push the rubber-tipped safety catch handle up, lift the hood, and prop it with the support rod.

Parking Brake: Pull the lever up to apply. To release, pull up slightly, push the button, and lower the lever. The dash indicator will go out when fully released.

Power windows in the HONDA ACCORD SEDAN 1993 function when the ignition is in the II position. The driver’s door has a master control panel for all windows. Push and hold the switch to the desired position. A main switch can lock out passenger window operation. Windows can still be operated for about 10 minutes after the ignition is turned off, provided neither front door has been opened.

To set the clock in the HONDA ACCORD SEDAN 1993:

1. Lower the clock lid.

2. Push and hold the M (minutes) button until the desired minutes are reached.

3. Push and hold the H (hour) button until the desired hour is reached.

4. Use the RESET button to synchronize to the closest hour (before the half hour resets to the current hour, after the half hour resets to the next hour).

The HONDA ACCORD SEDAN 1993 uses four basic controls: fan switch, temperature lever/dial, function lever/buttons, and the air conditioning switch. Turn the fan switch clockwise to increase airflow. Use the temperature control to adjust warmth. Select function buttons to direct air to vents, floor, or defroster. Use the recirculation button to shut off outside air for faster cooling or to keep out smoke/dust.

If the moonroof of the HONDA ACCORD SEDAN 1993 will not close electronically:

1. Remove the round plug near the rear center of the headliner.

2. Insert the moonroof wrench from the tool kit into the socket.

3. Turn the wrench until the moonroof is in the closed position.

4. Replace the plug.

If the radio in the HONDA ACCORD SEDAN 1993 has been disconnected from power, it will display “Code”. Enter the five digit security code using the preset station buttons. If an error is made, continue entering digits until a beep sounds, then re-enter the correct sequence. If the code is entered incorrectly three times, you must wait one hour with the radio ON before trying again.

The HONDA ACCORD SEDAN 1993 requires unleaded gasoline with a pump octane number of 86 or higher. Using leaded gasoline will damage the emission controls. Gasohol containing up to 10% ethanol or up to 15% MTBE by volume may be used. Methanol up to 5% by volume is allowed if it contains cosolvents and corrosion inhibitors.

Open the fuel door of the HONDA ACCORD SEDAN 1993 by pulling the lever on the left side of the driver’s seat. Turn the screw-in cap slowly counterclockwise and wait for any hiss of residual pressure to stop before removing it completely. Place the cap on the inside of the door while refueling. When finished, tighten the cap clockwise until ratchetting clicks are heard.

Recommended cold tire pressures for the HONDA ACCORD SEDAN 1993 are:

US DX/LX and Canada LX/EX: 29 psi (200 kPa).

US EX/SE and Canada EX-R/SE: 32 psi (220 kPa).

COMPACT spare tire: 60 psi (415 kPa).

Check pressures when tires have been parked for at least 3 hours or driven less than 1 mile.

The ignition switch of the HONDA ACCORD SEDAN 1993 has four positions:

0-LOCK: Key can be inserted or removed. Steering column locks when key is removed.

I-ACCESSORY: Accessory circuits (radio, etc.) are on, but the ignition is off.

II-ON: Normal running position.

III-START: Starter engages to start the engine. Key returns to II when released.

To start the HONDA ACCORD SEDAN 1993:

1. Apply the parking brake.

2. Push the clutch pedal all the way in (the engine will not crank otherwise).

3. Shift the transmission to neutral.

4. With your foot off the accelerator, turn the key to III for no more than 15 seconds. If it does not start, wait 10 seconds before trying again.

For best fuel economy in the HONDA ACCORD SEDAN 1993, shift at these speeds during normal acceleration:

If you cannot shift out of Park in the HONDA ACCORD SEDAN 1993:

1. Turn the ignition off and remove the key.

2. Insert the key into the Shift Lock Release slot to the right of the lever.

3. Press and hold the key down while pushing the button on the shift handle to move the lever to Neutral.

4. Remove the key, restart the engine, and then shift to the desired gear.

The HONDA ACCORD SEDAN 1993 has a maximum trailer weight limit (trailer plus cargo) of 1,000 lbs (450 kg). The tongue load must not exceed 100 lbs (45 kg), which should be approximately 10% of the total trailer weight. Do not tow a trailer during the first 600 miles (1,000 km) of the vehicle’s life.

Check the oil in your HONDA ACCORD SEDAN 1993 a few minutes after shutting off the engine. Ensure the car is on level ground. Remove the orange marked dipstick, wipe it clean, and re-insert it fully. Pull it out and check the level; it should be between the upper and lower marks. If low, add oil through the fill cap until it reaches the upper mark.

The HONDA ACCORD SEDAN 1993 requires “Energy Conserving II” SG grade oil. 5W-30 viscosity is preferred for all temperatures. The engine oil change capacity, including the filter, is 4.0 US quarts (3.8 liters, 3.3 Imperial quarts).

For the HONDA ACCORD SEDAN 1993:

Manual Transmission: Remove the filler bolt beside the right axle with the engine off. Feel inside the hole; the oil should be at the bottom edge. If low, add API Service SF or SG motor oil.

Automatic Transmission: Check with the engine off and car on level ground. Use the yellow marked dipstick at the right end of the housing. Level should be between upper and lower marks. Use Honda Premium Formula Automatic Transmission Fluid or DEXRON II ATF.

In the HONDA ACCORD SEDAN 1993, check that the fluid levels in the brake, ABS (if equipped), and clutch reservoirs are between the MAX and MIN marks. Use only DOT 3 or DOT 4 brake fluid from a sealed container. If levels are low, it may indicate wear or leakage and should be checked by a dealer. Ensure the arrow on the brake reservoir cap points forward after installation.

Check the power steering fluid in the HONDA ACCORD SEDAN 1993 when the engine is cold and the car is on level ground. The level must be between the upper and lower marks on the reservoir. Use only GENUINE HONDA Power Steering Fluid-V. Using other fluids like ATF will damage the system.

The HONDA ACCORD SEDAN 1993 uses the following recommended spark plugs:

Normal Driving: ZFR5F-11 (NGK) or KJ16CR-L11 (NIPPONDENSO).

Hot Climates/High Speed: ZFR6F-11 (NGK) or KJ20CR-L11 (NIPPONDENSO).

The plug gap should be 0.04 in (1.1 mm). Plugs should be replaced every 24 months or 30,000 miles.

In the HONDA ACCORD SEDAN 1993, one fuse box is under the dashboard on the driver’s side and the other is in the engine compartment on the right front fender. To check, turn off the ignition and switches. Use the fuse remover to pull a suspected fuse. If the wire inside is burned through, replace it with a new fuse of the same rating or lower. Never use a higher capacity fuse.

To change a tire on the HONDA ACCORD SEDAN 1993:

1. Park on firm, level ground, apply the parking brake, and turn on hazards.

2. Block the wheel diagonally opposite the flat tire.

3. Loosen lug nuts 1/2 turn counterclockwise.

4. Use the provided jack at correct jacking points to raise the car until the tire is off the ground.

5. Remove lug nuts and wheel.

6. Install the spare and hand-tighten nuts.

7. Lower the car and tighten lug nuts to 80 lb-ft (110 N.m) in an X pattern.

To jump start the HONDA ACCORD SEDAN 1993:

1. Connect one cable to the positive (+) terminal of the booster battery and then to the positive (+) terminal of the dead battery.

2. Connect the second cable to the negative (-) terminal of the booster battery.

3. Connect the other end of the negative cable to the engine block of the HONDA ACCORD SEDAN 1993 at the ground cable, not the battery post.

4. Start the car with the booster battery, then start the dead car. Reverse the procedure exactly to remove cables.

The Required Maintenance Schedule for the HONDA ACCORD SEDAN 1993 generally requires service every 7,500 miles (12,000 km) or 6 months. For severe driving conditions, certain items like engine oil and filter should be replaced every 3,750 miles (6,000 km) or 3 months, and the air cleaner element every 15,000 miles (24,000 km).

If the HONDA ACCORD SEDAN 1993 is stuck, call a professional towing service. Do not rev the engine or allow wheels to spin at high speed. For automatic transmissions, do not attempt to free the car by rocking it alternately between forward and reverse gears, as this causes severe transmission damage.