HILTI NMX 6-22 (01) PDF Document

The HILTI NMX 6-22 is a mixer designed for mixing materials of low or high viscosity, depending on the mixing paddle used.

For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in the technical data tables in the operating instructions.

For these batteries, use only Hilti chargers of the type series stated in the operating instructions.

To check the battery status, short-press the release button on the battery. The state of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.

To check the battery’s state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example, a battery that has been dropped or pierced, or has external heat damage.

The noise and vibration values are in accordance with EN 62841.

Noise information

Total vibration

Before any preparations, ensure the product is switched off before inserting the battery, and remove the battery before making any adjustments or changing accessories to prevent inadvertent starting.

Charging the battery:

1. Before charging, read the operating instructions for the charger.

2. Make sure the contacts on the battery and charger are clean and dry.

3. Use an approved charger to charge the battery.

Inserting the battery:

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

Removing the battery:

1. Press the battery release button.

2. Remove the battery from the product.

1. Lock the drive spindle by setting the spindle locking switch to the locked position symbol.

2. Screw the mixing paddle on to the drive spindle.

3. Tighten the mixing paddle using an open-ended wrench with a width across flats of 19 mm and another with a width across flats of 22 mm.

4. Remove the open-ended wrench.

5. Set the spindle locking switch to the unlocked position symbol.

Always hold the product with both hands on the provided grips, as it produces high torque and might rotate about its own axis. Immerse the mixing paddle in the material to be mixed before you switch the product on.

Selecting the speed:

Set the speed selector switch to the desired speed.

Switching on and off:

1. Press and hold down the switch-on interlock and press the on/off button. The product will start. You can release the switch-on interlock as soon as you have the on/off switch held down.

2. Release the on/off switch. The product switches off, and the switch-on interlock automatically jumps into the locked position.

Always remove the battery before carrying out care and maintenance tasks to avoid risk of injury.

Care of the product:

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Li-ion batteries:

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g., by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

Maintenance:

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.

Transport:

Always transport your products with the batteries removed to prevent accidental starting.

• Remove the battery/batteries.

• Never transport batteries loose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.

• Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.

• Prior to each use and before and after prolonged transport, check the product and the batteries for damage.

Storage:

Always store your products with the batteries removed to prevent accidental damage caused by defective or leaking batteries.

• Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.

• Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.

• Never leave batteries in direct sunlight, on sources of heat, or behind glass.

• Store the product and batteries where they cannot be accessed by children or unauthorized persons.

• Prior to each use and before and after prolonged storage, check the product and the batteries for damage.

If a problem occurs, always observe the charge-status and fault indicator of the battery. If you are unable to rectify the problem by yourself, please contact Hilti Service.

Incorrect disposal can lead to health hazards due to escaping gases or liquids. Do not dispose of power tools, electronic equipment, or batteries as household waste.

• DO NOT send batteries through the mail!

• Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

• Dispose of your battery out of the reach of children.

• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.