Free English HIKVISION DS-K1201AMF (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD HIKVISION DS-K1201AMF (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the components described in the HIKVISION DS-K1201AMF appearance diagram?
The components of the HIKVISION DS-K1201AMF are described in the following table:
| No. | Name |
| 1 | Fingerprint Scanner |
| 2 | Cable Interface of RS-485, Power, LED Control, etc. |
| 3 | DIP Switch |
How do I configure the RS-485 address using the DIP switch on the HIKVISION DS-K1201AMF?
The DIP switch module consists of switches 1 to 4, from left to right, representing the RS-485 address.
The description of the DIP Switch settings is as follows:
| Icon | Description |
| 1 | Represent ON in binary mode |
| 0 | Represent OFF in binary mode |
For example, the binary value of the status where switches 1 and 2 are ON and switches 3 and 4 are OFF is 1100.
Note: The DIP switch of RS-485 address should reach the access control devices requirements. For different access control devices, the DIP switch addresses may be different.
What are the definitions for the cables used when wiring the HIKVISION DS-K1201AMF in RS-485 communication mode?
The description of the 5 cables is shown below:
| Color | Description |
| Blue | RS-485 – |
| Yellow | RS-485 + |
| Red | PWR (DC +12V) |
| Black | GND (Power Grounding) |
| Black | GND (RS-485 Grounding) |
What are the steps for wiring the HIKVISION DS-K1201AMF controller using RS-485 communication mode?
The purpose is to wire the cables between the controller and the card reader to establish communication between them.
Steps for RS-485 communication mode:
1. Set the DIP switch for RS-485 address. For Details, refer to 2.1 Introduction for DIP Switch.
2. Wire the cable between the controller and the card reader as shown in the wiring diagram.
What are the steps for physically installing the HIKVISION DS-K1201AMF card reader onto a wall or ceiling?
Before you start, set the DIP switch. For details, refer to 2.1 Introduction for DIP Switch.
Steps:
1. Fix the mounting plate on the wall with 2 provided screws. Note: Do not warp the mounting plate when installing.
2. Connect the cables between the controller and the card reader. For details, refer to 2.3 Wiring Cables.
3. Unscrew the screw at the bottom of the card reader.
4. Buckle the card reader up to the plate.
5. Fasten the card reader to the plate with the set screw.
What do the different sound prompts on the HIKVISION DS-K1201AMF indicate during operation?
After the card reader is powered on, the LED status indicator will turn green and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed.
The description of prompt sounds is detailed below:
| Sound Prompt | Description |
| One beep | Swiping card prompt. For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card. |
| Two rapid beeps | The operation of pressing keys or swiping card is valid. |
| Three slow beeps | The operation of pressing keys or swiping card is invalid. |
| Rapidly continuous beeps | Prompt for tamper-proof alarm. Prompt for buzzer alarm. |
| Slowly continuous beeps | The card reader is unencrypted. |
What do the different LED indicator statuses mean on the HIKVISION DS-K1201AMF?
The description of the LED Indicator Statuses for the HIKVISION DS-K1201AMF is as follows:
| LED Indicator Status | Description |
| Green (blink for 1 time), and red (blink for 3 times) | The card reader is power on. |
| Green and blinking | For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card. The operation of configuring the fingerprint. The operation of swiping card is valid. |
| Solid green for 2s | Card reader is working normally. |
| Solid red | The operation of swiping card is invalid. |
| Red and blink for 3 times | The operation of swiping card is invalid. |
| Red and blinking | For RS-485 protocol: Registering failed or card reader is offline. |
What are the recommended guidelines for correctly scanning a fingerprint on the HIKVISION DS-K1201AMF?
Recommended Finger:
Forefinger, middle finger or the third finger.
Correct Scanning:
You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
Environment:
The scanner should avoid direct high light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again.
Others:
If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
CLICK HERE TO DOWNLOAD HIKVISION DS-K1201AMF (01) PDF DOCUMENT