Free English HARMONY HMO7553R (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD HARMONY HMO7553R (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the dimensions and intended operating conditions of the HARMONY HMO7553R merchandiser?
The HARMONY HMO7553R merchandiser measures 75 1/4 inches in length (includes 1-inch end panels), 32 1/8 inches in depth, and 52 5/8 inches in height (includes levelers at 1 1/4 inches below the base frame).
It is designed to merchandise packaged products at 41 °F (5 °C) or less product temperatures (unless customized with wire rack shelving).
What are Type 1 versus Type 2 ambient store conditions for the HARMONY HMO7553R?
For Type 1 Conditions: Ambient store conditions must be maintained at a maximum humidity of 55% and maximum temperatures of 75 °F (24 °C).
For Type 2 Conditions: Ambient store conditions must be maintained at a maximum humidity of 60% and maximum temperatures of 80 °F (27 °C).
If unsure whether the unit is designed for Type 1 or Type 2, check the tag next to the serial label.
What compliance requirements apply to the HARMONY HMO7553R?
This equipment must be installed in compliance with all applicable NEC, federal, state, and local electrical and plumbing codes.
What electrical hazard warnings must be observed when servicing the HARMONY HMO7553R?
Risk of electric shock: Disconnect power before servicing the unit.
Caution: More than one source of electrical supply is employed with units that have separate circuits. Disconnect all electrical sources before servicing.
What moving parts hazard warning should be observed on the HARMONY HMO7553R?
Hazardous moving parts: Do not operate the unit with covers removed.
Fan blades may be exposed when the deck panel is removed. Disconnect power before removing the deck panel.
What hot surface warnings apply to the HARMONY HMO7553R condensate pan?
Electric coil condensate pans are hot! Disconnect power and allow the pan to cool before cleaning or removing it from the case.
What circuit breaker is recommended for the HARMONY HMO7553R?
If N.E.C. (National Electric Code) or local codes require GFCI (Ground Fault Circuit Interrupter) protection, the use of a GFCI breaker is strongly recommended.
What are the placement and clearance guidelines to prevent adverse conditions for the HARMONY HMO7553R?
The unit must be kept at least 15 feet from exterior doors, overhead HVAC vents, or any air curtain disruption to maintain proper temperatures.
The unit must not be exposed to direct sunlight or any heat source (ovens, fryers, etc.).
Keep at least 8 inches of clearance above the unit for air discharge on self-contained units.
What lamp replacement guidelines must be followed for the HARMONY HMO7553R?
LED lamps reflect specific size, shape, and overall design. Any replacements must meet factory specifications.
Fluorescent lamps have been treated to resist breakage and must be replaced with similarly treated lamps.
What checks must be performed on the condensate pan and plug of the HARMONY HMO7553R before powering up?
Before powering up the unit, check the following to prevent water damage to flooring:
The condensate pan must be positioned directly under the condensate drain.
The condensate pan plug must be securely plugged into the receptacle.
Check that the overflow pan is fully functional.
If wicking material is used, check that it is secure.
What are the power cord and plug maintenance requirements for the HARMONY HMO7553R?
To avoid the risk of electric shock, if the cord or plug becomes damaged, replace it only with a cord and plug of the same type.
Where can the wiring diagram be found on the HARMONY HMO7553R?
Each case has its own wiring diagram folded inside its own packet. Wiring diagram placement may vary; it may be placed near the ballast box, field wiring box, raceway cover, or another related location.
What should be checked regarding shipment condition, delivery damage, and uncrating of the HARMONY HMO7553R?
Check all equipment for damage before and during unloading.
If damage is discovered during delivery via a 3rd party carrier: Describe the damage on the freight bill and obtain the driver’s signature. The carrier will supply claim forms.
Uncrating equipment at a facility other than the installation site may result in severe damage to the unit when transporting to the final destination. The equipment should only be uncrated at the installation site.
If damage is discovered after uncrating with a 3rd party carrier: Contact the carrier within 10 days of delivery for procedures and retain all packaging.
How do you remove the case shipping brackets from the HARMONY HMO7553R skid?
Step 1: Remove the screws holding the case shipping brackets to the skid.
Step 2: Remove the case shipping brackets from the skid.
How do you remove a HARMONY HMO7553R with levelers from the shipping skid?
Step 1: To prevent damage, support the case while sliding it toward the edge of the skid.
Step 2: When the case is at the edge of the skid, carefully lower it to the floor so two levelers rest on the floor.
Step 3: Carefully slide the skid out from under the case.
Step 4: After removal of the case from the skid, place it into position.
How do you remove a HARMONY HMO7553R with casters from the shipping skid?
Step 1: Place a ramp up against the skid to allow the case to smoothly slide off from the skid.
Step 2: Maintain support of the case at all times, or the center of gravity may cause the case to fall.
Step 3: Unlock the casters. Slide the unit to the rear of the skid. Slide down the ramp and off from the skid.
What ventilation and airflow clearances are required for the HARMONY HMO7553R?
Self-contained refrigerated cases must maintain an airflow clearance of 6 inches (minimum) to 12 inches (recommended) at the front and rear.
Ensure that air grilles are checked and kept clear of obstructions, as restriction of airflow can void the warranty.
What is the step-by-step procedure for caulking and bolting HARMONY HMO7553R units together in a lineup?
Step 1: Begin all lineups by leveling from the highest point of the floor.
Step 2: After the first case is level, apply industrial grade butyl caulk on non-visible areas at the case end. Use industrial grade silicone sealant on visible areas at the case end.
Step 3: Form two caulk/sealant lines: one Sanitation Bead and one Refrigeration Bead.
Step 4: Line up the second case bolt-hole to bolt-hole with the first case.
Step 5: Using supplied bolts, insert bolts in the bolt hole locations (decking may need to be removed to access lower bolt holes).
Step 6: Caution! Ensure the front of the cases are flush with each other, and all cases are at the same height after leveling.
Step 7: Using supplied nuts and bolts, lightly tighten each of the 5 to 8 bolts in a cross-wise pattern. Work around the pattern, tightening more firmly at each pass. Do not firmly tighten one bolt and then start on the next.
Step 8: After the cases are bolted together, level the second case. Repeat this process for each case to be adjoined.
Step 9: After all lined-up cases are level, seal all seams with industrial grade silicone sealant.
How do you position, align, and adjust the levelers on the HARMONY HMO7553R?
Step 1: Before adjusting levelers, make certain that the case is in proper position and, if required, aligned with adjoining cases. This may require repositioning the case being installed or already positioned cases.
Step 2: You may need to remove the front and/or rear toe-kick to access the levelers.
Step 3: Use an adjustable wrench to adjust the leveler until the case is level and plumb.
Step 4: Depending upon case weight, it may be necessary to use a pry bar to raise the case. Use the pry bar only on the base frame; do not use it on the toe-kick (it may buckle) or the end panel (it may chip).
How are frame support rails shimmed on the HARMONY HMO7553R?
Shims are provided with cases that have frame support rails. Use the shims under the frame support rails to level the case.
After the case is in position, it must be sealed to the floor to prevent entry or leakage of liquid or moisture.
How do you remove the front grille on the HARMONY HMO7553R?
For grilles with screws: Remove the front grille retainer screws (both horizontal at each end and vertical along the entire underside of the front panel). The front grille will fall forward and can be lifted up and away from the case. Reinstall in reverse order and tighten retainer screws.
For grilles without screws: The front grille is held in place with retaining hooks at each end. Simply lift the front grille up and off the case. No screws are required.
How do you access and remove the rear filter, rear grille, and rear panel on the HARMONY HMO7553R?
Optional Magnetized Filter: Lift and remove the magnetized condenser coil filter from the outside of the rear grille (it is held by magnetic strips).
Rear Grille: Remove by lifting the grille slots up and off the rear panel’s retainer hooks.
Rear Panel: Remove the four Phillips screws (not flat-head) holding the panel in place.
Compressor Pan Shipment Screws: At initial access to the refrigeration package, remove the compressor pan shipment screws (one at each end) using a Phillips screwdriver with an extension.
What are the steps to start up the HARMONY HMO7553R merchandiser?
Step 1: Power the unit:
For Remote Units: The case is hard-wired and powers up when power is supplied.
For Self-Contained Units: Turn on the Main Power switch located at the case rear, lower right. The temperature controller is located at the case rear, lower left.
Step 2: Turn on the lights. The light switch is located on the inside of the case at the top right (viewed from the case rear).
Step 3: Verify lighting operation. All lights should illuminate simultaneously. First-time lighting may require a short warm-up period; slight dimming or flickering of new bulbs is normal.
Step 4: Ensure all lights are plugged in or receptacles are capped, as the lighting is wired in series.
Where are the electrical connections located on remote HARMONY HMO7553R models?
Field wiring connections and electrical access are located at the customer-left side of the case. Single-phase leads are provided.
What warning must be followed regarding drain hose and trap placement in the HARMONY HMO7553R?
Regardless of the evaporator system type, the hose and drain trap must be secured and positioned over the evaporator pan to prevent water seepage and spillage.
When sliding out the condenser unit, be careful that the drain is not pulled from its proper position.
How do you operate the night air curtain that pulls up from the lower section on the HARMONY HMO7553R?
Step 1: Grasp the handle at the lower-front-center area of the case and pull upward.
Step 2: Attach the night air curtain retaining magnets to the metal plate located in front of the honeycomb air diffuser.
Step 3: Caution: Do not slide or drag the night air curtain across the metal plate when extending and attaching; lift the curtain end straight up and off to avoid scratching.
Step 4: To retract: Grasp the handle, lift up and off from the magnetic attachment, and carefully wind the night air curtain back into its roller roll in the lower section.
Step 5: Caution: Do not allow the spring-loaded night air curtain to freely snap back into the roll, as this can destroy its tension and retractability.
How do you install and operate an optional top-mounted pull-down night air curtain on the HARMONY HMO7553R?
Step 1: If installing via a retrofit kit, center the night curtain assembly along the angled honeycomb support using the attachment magnets.
Step 2: Grasp the handle and pull downward to the desired area outside the acrylic sneeze guard.
Step 3: Attach the magnets at the attachment points along the plate outside the acrylic sneeze guard.
Step 4: To return to the retracted position, grasp the handle, lift away from the magnetic attachment, and carefully wind the curtain back into its roll.
Step 5: Caution: Do not let the spring-loaded curtain snap freely into the roll.
Step 6: To remove the entire assembly, firmly lift it straight up and off the support without sliding or dragging.
How is the security grid installed on the HARMONY HMO7553R?
Step 1: Due to size and weight, installation requires two people.
Step 2: Hoist the security grid directly over the front air deflector.
Step 3: Drop the two security grid positioning tabs (one at each end) directly into the baffle airflow slots.
Step 4: After positioning the tabs in the airflow slots, carefully and slowly lean the security grid back against the two security brackets.
Step 5: Slide the two padlocks through the security grid and security brackets, then securely lock them (one key fits both padlocks).
How is the security grid removed and stored on the HARMONY HMO7553R?
Step 1: Due to weight and size, removal requires two people.
Step 2: Unlock and remove the padlocks.
Step 3: Lean the security grid forward slightly.
Step 4: Lift upward and out of the baffle airflow slots.
Step 5: Store the security grid, padlocks, and keys in a secure location to prevent theft or damage.
How do you remove shelf assemblies and fluorescent lamps on the HARMONY HMO7553R?
To remove the shelf assembly:
1. Remove the glass shelves.
2. For lighted shelving, unplug the light cord.
3. Lift the light shelf upward to separate it from the brackets.
4. Remove the rear shelf support.
5. Remove the brackets (pliers may be required to remove the nylon shipping bracket retainer).
To remove a fluorescent lamp:
1. Rotate the lamp 1/4 turn in either direction to disengage the pinned contacts from the mounting sockets.
2. Remove the bulb by applying even pressure from the back side at the bulb ends and pulling contacts from the sockets.
To install a fluorescent lamp:
1. Align the lamp pins with the socket slots.
2. Insert pins into the socket by rotating the bulb 1/4 turn to secure the pinned contacts.
3. Rotate the remaining contacts (1/4 turn) into the remaining socket contacts.
How do you remove, replace, and connect LED light fixtures on the HARMONY HMO7553R?
Step 1: Disconnect the existing LED light from its brackets and self-adhesive tape.
Step 2: Firmly grasp the LED light while applying outward pressure to the brackets, then twist the LED out and away from the bracket to release.
Step 3: Connect the plug to the LED light at the raceway side of the case.
Step 4: Ensure the oval form of the plug aligns and connects properly with the oval form of the LED light (verify that the cord does not double back) or the LED will not light up.
What is the daily cleaning procedure for the exterior surfaces of the HARMONY HMO7553R?
Acrylic Sneeze Guard: Clean daily with a mild soap and water solution and a soft cloth. Never use ammonia-based cleaners or abrasive cloths, as they cause surfaces to cloud over time.
Glass: Clean side, front curved, and rear glass daily with household or commercial glass cleaner and a soft cloth.
Wood, Laminate, and Painted Surfaces: Clean daily with a warm soap and water solution and a soft cloth. Never use wire cloth or abrasive cleaners.
How should store personnel clean the air filter on the rear grille of the HARMONY HMO7553R?
Frequency: Weekly to monthly, depending upon the environment (must be cleaned at least monthly).
Step 1: Remove the magnetized filter from the case.
Step 2: Submerse the filter in warm, soapy water.
Step 3: Use a soft-bristled brush to remove dust, grease, and grime.
Step 4: Rinse thoroughly with clean water.
Step 5: Allow the filter to dry completely before returning it to the case.
What is the cleaning routine for interior shelves, decks, air return grilles, and condenser coil performed by store personnel on the HARMONY HMO7553R?
Daily – Shelves/Decks/Risers: Clean with a warm soap and water solution. For stubborn stains, decks and risers can be removed and cleaned or submersed in hot, soapy water. Rinse thoroughly, dry, and return to case.
Weekly – Shelf Supports, Air Return Grilles, Decking: Wipe off with a moist cloth. Shelf supports and air return grilles can be removed for thorough cleaning. Caution: Decking is not to be removed by store personnel.
Monthly – Condenser Coil: Vacuum or brush the condenser coil at the front of the case using a metal or fiber brush to remove dust and dirt. Be careful not to damage the coil fins.
What are the general cleaning instructions for stainless steel surfaces on the HARMONY HMO7553R?
Step 1: Wash with a solution of liquid dishwashing detergent and hot water.
Step 2: Rinse with pure hot water from a spray bottle while wiping with a clean sponge to remove soap residue from microscopic grooves.
Step 3: Dry with a clean, soft cloth or paper towel.
Caution: Never clean stainless steel with scouring powder or steel wool as they scratch and erode the surface, which causes rust to form.
How do you brighten, remove streaks, polish, and remove rust from stainless steel on the HARMONY HMO7553R?
Brightening:
Method 1: Polish with a soft cloth/sponge using a solution of 1 part vinegar to 2 parts water in a spray bottle. Rinse with pure hot water from a spray bottle and dry.
Method 2: Sprinkle baking soda on a sponge and rub gently. Rinse with hot water and dry.
Removing Streaks or Stains:
Method 1: Place 2 teaspoons of rubbing alcohol on a microfiber cloth and rub along the grain; allow to air dry.
Method 2: Dip a cloth/sponge in club soda and rub gently. Rinse with hot water and dry.
Polishing:
Apply a dab of olive oil onto a clean soft cloth. Spread over the area with firm circular motions. Dry buff with a clean cloth or wet buff using an ounce of white vinegar to remove oily finish. Rinse with hot water and dry.
Removing Rust:
Treat using products such as CLR (calcium, lime, and rust remover) or Chemetall Oakite 33. Follow all manufacturer precautions and instructions to prevent food contamination or injury.
What store-level troubleshooting steps should be taken if the HARMONY HMO7553R lights are not working?
Step 1: Check that the light switch is in the on position.
Step 2: Check that all light cords and plugs are properly connected and receptacles are capped where applicable.
Step 3: If lights still do not come on, call a service provider.
What store-level troubleshooting steps should be taken if the HARMONY HMO7553R is not holding proper temperature?
Step 1: If a large amount of warm product was added, allow time for temperature adjustment. Pre-chill all product before placing it in the case.
Step 2: Check that the case is not positioned in direct sunlight or near an HVAC or heating vent.
Step 3: Verify that the air filter and condenser coil have been properly cleaned.
Step 4: Check air return grilles for obstructions. Do not place product on air return grilles.
Step 5: If the case still does not hold proper temperature, contact a service provider.
What actions should store personnel take if water is on the floor, the fan emits noise, or the case is not level on the HARMONY HMO7553R?
Case Is Not Level: Refer to the case positioning and leveling instructions to adjust the levelers.
Water Is On The Floor: Call a service provider immediately.
Fan Emits Excessive Noise: Call a service provider.
How should service technicians clean the evaporator fan shroud, tub, and drain of the HARMONY HMO7553R?
Caution: Due to rotating fans, turn off the case and disconnect the electrical plug from the wall outlet before cleaning.
Fan Shroud Area (Monthly): Turn off power, remove the decks, and wipe down the fan shroud and surrounding tub area with a moist cloth.
Tub and Drain Area (Quarterly): Turn off power and disconnect plug. Vacuum the tub under the decks. Clean with a soap and water solution and wipe dry with a clean cloth. Remove any debris that could clog the drain.
How should service technicians inspect and maintain the wicking material on the HARMONY HMO7553R?
Frequency: Quarterly (for hot gas condensate pans).
Step 1: Slide the refrigeration system out from under the unit.
Step 2: Inspect the wicking material to see if it is dirty, worn, tattered, torn, or disintegrating.
Step 3: If decomposing or in disrepair, replace it with new wicking material.
What troubleshooting steps should a technician take when water is found on the floor around a HARMONY HMO7553R?
Immediate containment: Use a wet-dry vacuum or mop/bucket to remove standing water, and use catch pans under the drain.
Check drain trap: Ensure it is free of debris.
Check drain hose: Verify it is correctly positioned over the evaporator pan (or floor drain for remote units).
Check ambient conditions: Verify conditions do not exceed 55% RH / 75 °F (Type 1) or 60% RH / 80 °F (Type 2).
Check evaporator pan float: Ensure proper operation on heat rod systems.
Check power: Confirm the evaporator pan is plugged in and power supply is continuous.
Check wicking material: On hot gas systems, check if wicking material is dirty or decomposed and replace if necessary.
What should a service technician check if fans emit excessive noise or are not working on the HARMONY HMO7553R?
If fans emit excessive noise:
1. Check that the case is aligned, level, and plumb.
2. Check the evaporator fan for cleanliness.
3. Unplug/power off fan motors and check the motor shaft for bearing wear.
4. Check that fan motors are securely mounted in brackets and fan blades are securely mounted to the motor.
5. Check for obstructions preventing blade rotation.
6. Check that the fan shroud is properly secured.
If fans are not working:
1. Check that the main power switch is turned on.
2. Verify fans are plugged into the fan shroud.
3. Check for foreign material obstructing the fans.
4. Check that fan blades rotate freely.
5. Verify power is reaching the fans and fan wiring is connected to terminal blocks.
What should a service technician check if the digital controller display is blank or the HARMONY HMO7553R system is not operating?
Check that utility power to the unit is on.
Check that the main power switch is in the on position.
Check the facility circuit breaker box for tripped circuits.
What technical troubleshooting checks apply when the HARMONY HMO7553R is not holding temperature?
Check for warm product: Warm product requires time to adjust; items must be pre-chilled.
Defrost cycle: Temperature rises during defrost mode and returns to normal afterward; the fourth LED indicates an active defrost cycle.
Environmental factors: Ensure unit is not exposed to direct sun, HVAC vents, or door drafts.
Coils and filters: Clean the magnetic air filter and condenser coil.
Air return: Ensure air grilles are unobstructed.
Refrigerant charge: Inspect the sight glass for flashing or low charge.
Controller set point: Check whether the setpoint temperature is adjusted too high.
What technical checks should be performed if the HARMONY HMO7553R condensing unit is not operating?
Check that the main power switch is turned on.
Determine if temperature controller settings are properly configured according to the unit’s serial label specifications.
What are the causes and troubleshooting checks when condensing head pressure is too high on the HARMONY HMO7553R?
Check that the condensing coil is clean and not covered.
Check that the condensing fans are operating properly.
Check that the refrigerant is not overcharged.
Check to verify there are no non-condensables in the system.
Check that the liquid line drier is not plugged.
Check that there are no close-offs obstructing airflow around the condensing coil.
Check the setpoint temperature to ensure it is not set too high.
Check system operating temperatures.
Check that the store ambient temperature does not exceed allowable limits.
What are the causes and troubleshooting checks when condensing head pressure is too low on the HARMONY HMO7553R?
Check that the refrigerant charge is not too low.
Check that the suction pressure is not too low.
Verify that the compressor valves are not damaged or failing.
What causes low suction pressure on the HARMONY HMO7553R, and what should be checked?
Check for low refrigerant charge.
Check if the thermal expansion valve (TXV) is restricted.
Check if the liquid line or filter is restricted.
Check that the evaporator fan motors are working.
Check if high superheat requires adjustment.
Check if the thermostatic element charge is depleted.
Check that there is no air seepage around the condensing coil.
Check that the evaporator coil is not iced up.
What causes high suction pressure on the HARMONY HMO7553R, and what should be checked?
Check if the refrigerant charge is too high.
Check if compressor valves are failing.
Check if the cooling load is excessively high.
Check if superheat adjustment is set too low.
Check TXV bulb installation for poor thermal contact or location in a warm area.
Check compressor sizing; low capacity indicates the compressor is undersized for the application.
What quarterly preventive maintenance must be performed on the HARMONY HMO7553R condensing coil?
Step 1: Turn off power to the case.
Step 2: Remove the access panel by lifting up and off or removing screws.
Step 3: Clean dust and dirt from the condenser coil using compressed air or an industrial strength vacuum.
Caution: Airborne dust can contaminate food; place wet rags over areas where air is blowing.
Warning: Coil fins are sharp; handle with care.
Step 4: Reinstall the access panel.
What quarterly preventive maintenance is required for the HARMONY HMO7553R refrigeration package and compressor area?
Warning: Disconnect power before cleaning. The evaporator pan is hot; allow it to cool completely before servicing.
Step 1: Slide or roll the compressor package out from under the case.
Step 2: Clean the evaporator pan using a scrub brush and a de-scaling solution such as CLR to remove corrosion, lime, and rust.
Step 3: Thoroughly rinse the pan with clean water from a spray bottle and wipe dry with a sponge or paper towel.
Step 4: Wipe dust and debris off fans, sight glass, overflow pan, and related parts using a moist cloth.
Step 5: Vacuum dust and dirt from the floor area under the case.
Step 6: Slide the refrigeration assembly back under the case and replace panels.
How do you remove, clean, and reinstall the honeycomb air diffuser on the HARMONY HMO7553R?
Removal:
1. Wedge a non-metallic device of suitable strength (such as a ballpoint pen) between the honeycomb and the end panel.
Caution: Use care not to dislodge the heating wire that prevents condensation on the lamp assembly.
2. Apply pressure to collapse the honeycomb so it can be pulled from the retainer.
3. Carefully pry downward and away from the retainer.
Cleaning:
Clean the honeycomb with a warm water and soap solution, submersing if necessary. Use a brush to remove stubborn residue. Dry using a vacuum in blow mode (not suction mode).
Installation:
1. Squeeze the honeycomb to allow it to fit into the retainer.
2. Carefully slide the honeycomb into place.
3. Adjust the honeycomb so it fits flat against the retainer without waves or misalignment.
How do you modify the temperature setpoint on the HARMONY HMO7553R Carel ir33 controller?
Step 1: Press and hold the “SET” key for at least 1 second.
Step 2: Use the UP or DOWN arrow keys to increase or decrease the setpoint.
Step 3: Quickly press and release the “SET” key again to confirm.
How do you modify parameters such as defrost and differential on the HARMONY HMO7553R Carel ir33 controller?
Step 1: Press and hold the “Prg/mute” and “SET” keys together for 5 seconds until the display flashes “0” (password prompt).
Step 2: Confirm by pressing the “SET” key.
Step 3: Press the UP or DOWN arrow keys to navigate to the category to modify.
Step 4: Press “SET” to select the parameter.
Step 5: Increase or decrease the value using the UP or DOWN arrow keys.
Step 6: Press “SET” to temporarily save the new value and return to parameter display.
Step 7: Press and hold “Prg/mute” for at least 5 seconds to permanently save changes. This also mutes the audible alarm buzzer and deactivates the alarm relay.
Important: If no button is pressed within 60 seconds, a timeout occurs and all modifications are lost.
How do you change the temperature unit display between Fahrenheit and Celsius on the HARMONY HMO7553R controller?
Step 1: Press and hold “Prg/mute” and “SET” together for at least 5 seconds until “0” appears.
Step 2: Press “SET” to confirm.
Step 3: Press UP or DOWN until reaching parameter “/ 5”.
Step 4: Press “SET” to modify the parameter.
Step 5: Press UP or DOWN to select “0” for Celsius (°C) or “1” for Fahrenheit (°F).
Step 6: Press “SET” to temporarily save the value.
Step 7: Press and hold “Prg/mute” for at least 5 seconds to permanently save the setting. All parameters automatically convert to the new scale.
How do you activate a manual defrost or reset manual alarms on the HARMONY HMO7553R Carel controller?
To activate manual defrost: Press and hold the “def” (down arrow) key for at least 5 seconds.
To reset manual alarms: Press and hold the “Prg/mute” and “aux” (up arrow) keys together for at least 1 second.
To activate or deactivate auxiliary output: Press and hold the “aux” key for 1 second.
What do the display icons mean on the HARMONY HMO7553R Carel ir33 controller?
Compressor icon: ON when compressor starts; flashes when activation is delayed by safety times.
Fan icon: ON when fans start; flashes when activation is disabled by external disabling or in progress procedures.
Defrost icon: ON when defrost is active; flashes when activation is disabled by external disabling or procedures in progress.
AUX icon: ON when auxiliary output is active; flashes when anti-sweat heater function is active.
Alarm icon: Flashes in the event of alarms during normal operation (high/low temp) or external digital input.
Clock icon: ON if at least one timed defrost is set; flashes if alarm clock is active.
Service (wrench) icon: Flashes in the event of malfunctions such as E2PROM errors or probe faults.
Continuous cycle icon: ON when continuous cycle function is activated; flashes when continuous cycle is requested.
What are the alarm and error codes displayed on the HARMONY HMO7553R Carel ir33 controller?
The following table summarizes the alarm and error codes, their relay/buzzer status, reset type, and descriptions:
| Code | Alarm Relay | Buzzer | Reset | Description |
|---|---|---|---|---|
| rE | ON | ON | Automatic | Virtual control probe fault |
| E0 | OFF | OFF | Automatic | Room probe S1 fault |
| E1 | OFF | OFF | Automatic | Defrost probe S2 fault |
| E2 | OFF | OFF | Automatic | Probe S3 fault |
| E3 | OFF | OFF | Automatic | Probe S4 fault |
| E4 | OFF | OFF | Automatic | Probe S5 fault |
| LO | ON | ON | Automatic | Low temperature alarm |
| HI | ON | ON | Automatic | High temperature alarm |
| AFr | ON | ON | Manual | Antifreeze alarm |
| IA | ON | ON | Automatic | Immediate alarm from external contact |
| dA | ON | ON | Automatic | Delayed alarm from external contact |
| dEF | OFF | OFF | Automatic | Defrost running |
| Ed1 | OFF | OFF | Automatic/Manual | Defrost on evaporator 1 ended by timeout |
| Ed2 | OFF | OFF | Automatic/Manual | Defrost on evaporator 2 ended by timeout |
| Pd | ON | ON | Automatic/Manual | Maximum pump down time alarm |
| LP | ON | ON | Automatic/Manual | Low pressure alarm |
| AtS | ON | ON | Automatic/Manual | Autostart in pump down |
| cht | OFF | OFF | Automatic/Manual | High condenser temperature pre-alarm |
| CHT | ON | ON | Manual | High condenser temperature alarm |
| dor | ON | ON | Automatic | Door open too long alarm |
| EE | OFF | OFF | Automatic | E2prom error, unit parameters |
| EF | OFF | OFF | Automatic | E2prom error, operating parameters |
What are the controller operating parameters on the HARMONY HMO7553R Carel ir33 controller?
The operating parameters table for the controller is as follows:
| Code | Parameter | UOM | Type | Minimum | Maximum |
|---|---|---|---|---|---|
| /5 | Select Celsius (°C) or Fahrenheit (°F) | flag | C | 0 | 1 |
| /c1 | Calibration of probe 1 | °C/°F | C | -20 | 20 |
| /c2 | Calibration of probe 2 | °C/°F | C | -20 | 20 |
| St | Temperature set point | °C/°F | F | r2 | r1 |
| rd | Control delta | °C/°F | F | 20 | 0.1 |
| dl | Interval between defrosts | hours | F | 0 | 250 |
| dt1 | End defrost temperature, evaporator | °C/°F | F | -50 | 200 |
| dP1 | Maximum defrost duration, evaporator | min | F | 1 | 250 |
| d6 | Display on hold during defrost | – | C | 0 | 2 |
| dd | Dripping time after defrost | min | F | 0 | 15 |
| d/1 | Display of defrost probe 1 | °C/°F | F | – | – |
Case-specific default parameters are listed on the serial label located near the electrical access of the case.
Where is the serial label located on the HARMONY HMO7553R and what information does it contain?
The serial label is located near the electrical access on the case.
It contains critical electrical ratings (volts, hertz, phase, amps), refrigerant type and charge amount, design high and low pressures, minimum circuit ampacity, maximum overcurrent protection, superheat temperature, BTUH requirements, defrost frequency/duration/failsafe limits, and regulatory standard conformity information.
CLICK HERE TO DOWNLOAD HARMONY HMO7553R (01) PDF DOCUMENT