HAIER HLTD500AEW (01) PDF DOCUMENT

If you smell gas, follow these instructions for your safety:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building, or area of all occupants.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow the basic precautions, including the following:

Read all of the instructions before using this appliance.

This appliance must be properly installed and located in accordance with the installation instructions before it is used.

Use this appliance only for its intended purpose as described in this user manual.

Do not use the dryer for commercial clothes drying.

Keep the area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

Keep the dryer area clear and free from items that would obstruct the flow of combustion and ventilation air through the louvered panel located on the rear of the dryer.

Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this appliance.

Do not dry items that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents or other flammable explosive substances, since they give off vapors which could ignite or explode.

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oil may contribute to a chemical reaction that could cause a load to catch fire.

If material has been used with any flammable liquids or solids, it should not be dried in the dryer until all traces of flammable liquids and fumes have been removed.

Do not reach into the appliance if the drum is moving.

Do not tamper with the controls.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturers of the fabric softener or product.

Do not use heat to dry items containing foam rubber or similarly textured rubber-like materials.

Clean the lint screen before or after each load.

The interior of the appliance and the exhaust duct should be cleaned periodically by qualified service personnel.

To minimize the possibility of electric shock, unplug this appliance from the power supply before attempting any maintenance or cleaning. NOTE: Switching off power with the Power button does NOT disconnect the appliance from the power supply.

Do not unplug your dryer by pulling on the power cord. Always grasp the plug firmly and pull straight out from the outlet.

Do not attempt to service, repair or replace any part of the appliance unless specifically recommended in this user manual or in published repair instructions that you understand and have the skills to carry out.

Before discarding or removing from service, remove the door to the drying compartment.

The gas installation must conform with local codes, or in absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

Installation must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by the state, province, or region where this appliance is being installed.

Combustible materials, gasoline, and other flammable vapors and liquids must not be stored near the dryer.

A) Power Cord (120 volt/60 Hz) (Gas Dryer)

B) Strain Relief Mounting Bracket (for Electric Dryer)

C) Terminal Block Access Cover (Electric Dryer)

D) Exhaust Outlet

E) Louvered Ventilation Panel

F) Gas Inlet Pipe (Gas Dryer)

G) Control Panel

H) Door Safety Switch

I) Lint Screen

J) Dryer Door

K) Leveling Feet

L) Front Panel

M) Interior Drum Light

N) Dryer Cabinet

Risk of Fire:

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

To reduce the risk of severe injury or death, follow all installation instructions.

DANGER:

When discarding or storing your old clothes dryer, remove the door or lid so that children cannot hide or get trapped inside your old appliance.

Tools Needed:

Phillips Screwdriver

Flat-Blade Screwdriver

Channel-Lock Adjustable Pliers

½” Open-End Wrench

Carpenter’s Level

Measuring Tape (12 ft [3.7 m] min.)

For gas installations only:

Pipe Wrench

2 Adjustable Wrenches

Additional Parts Required:

4″ (10.2 cm) Rigid or Flexible Metal Exhaust Ducting

Vent Clamps

Duct Tape

Power Cord (US Electric Dryer Only): A power supply cord kit must be purchased to meet local electrical codes. The dryer must use a 3 or 4-wire NEMA 14-30 or 10-30 type SRDT or ST (as required) power supply cord rated at 120/240 volt AC minimum, 30 amp, with 10 AWG conductors terminated with upturned ends or closed loop connectors and marked for use with clothes dryers, along with a UL Listed Strain Relief.

Gas Hookup Parts (Gas Dryer Only): ” NPT Elbow, ” NPT Flare Adapter Fitting, ” Flexible Gas Connector, Pipe-Joint Compound.

Mobile Home Installation Kit (Gas Dryer for Mobile Home Only).

Do not install the dryer where gasoline or other flammables are kept or stored. If the dryer is installed in a garage, it must be a minimum of 18 inches (45.7 cm) above the floor. Failure to do so can result in death, explosion, fire or burns.

The dryer must be installed on a solid floor. A concrete floor is the best.

The floor should be level with a maximum slope of 1″ (2.5 cm) under the entire dryer.

A suitable location is protected from direct sunlight and heat sources such as radiators, baseboard heaters, or cooking appliances.

Do not install on carpeting.

The location must have the appropriate electrical and gas supply outlets.

Do not install the dryer in an area where the dryer will come into contact with curtains, thick carpet, or anything that might obstruct the flow of combustion and ventilation air.

Do not install or store this appliance where it will be exposed to water and/or to the weather.

Minimum Clearances:

Side clearance: Space on the sides of the dryer is required to avoid noise transfer.

Rear clearance: Space at the rear of the dryer is necessary to accommodate exhaust ducting.

Closet door to front of dryer: 1″ (2.5 cm)

Top of dryer to ceiling/shelf: 15″ (38.1 cm)

Rear of dryer to wall: 5½” (14 cm)

Other Requirements:

This dryer must be vented to the outdoors.

Do not install the dryer in a closet with a solid door.

A closet door must be louvered or vented with a minimum of 120 sq. in. (774.2 sq. cm) of opening equally divided at the top and bottom of the door. The airflow must not be obstructed in any way. The top and bottom openings must each be at least 60 in.² (387.1 cm²).

No other fuel-burning appliance shall be installed in the same closet as the gas dryer.

Grounding Instructions: This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Electric Dryer (U.S. Only): The dryer must be plugged into a properly grounded 3 or 4-wire, single phase, 120/240 volt (or 120/208 volt), 60Hz, AC-only electrical outlet connected to an individual 30-amp circuit. Do not operate a washer and dryer on the same circuit. A dryer operating on a 208-volt power supply will have longer drying times. A power cord kit must be purchased separately. A UL listed strain relief must be attached to the dryer to hold the power cord.

Electric Dryer (Canada Only): The dryer must be plugged into a properly grounded 4-wire, single phase, 120/240 volt, 60Hz, AC-only electrical outlet connected to an individual 30-amp circuit. Do not operate a washer and dryer on the same circuit.

Gas Dryer: The gas dryer must be plugged into a properly grounded 3-wire, single phase, 120 volt, 60Hz, AC-only electrical outlet, fused with a 15-amp time-delay fuse or circuit breaker. The dryer is equipped with a power cord that has a 3-prong plug. Do not cut or remove the grounding prong. Do not use a 3-prong plug adapter or an extension cord.

Gas Supply: The gas service must conform with local codes and the latest edition of the National Fuel Gas Code, ANSI Z223.1, or in Canada, CAN/CGA B149.1. The dryer is equipped for Natural Gas but can be converted for LP (Liquid Propane) Gas by a qualified technician.

Gas Supply Line: The line should be ½” (1.3 cm) pipe with an individual manual shutoff valve within 6 ft (183 cm) of the dryer. A ” NPT minimum plugged tapping for a test gauge must be installed upstream of the gas supply connection. The supply line should terminate with a ” NPT flare adapter fitting.

Gas Supply Connection: Use a new flexible stainless steel gas connector (Design Certified by the American Gas Association or CSA International) to connect the dryer to the rigid gas supply line. Use an elbow and a ” flare x ” NPT adapter fitting between the connector and the dryer gas pipe to prevent kinking.

Burner Input Requirements:

Elevations up to 10,000 ft. (3,048 m): The dryer is certified for use at these altitudes without burner input adjustments.

Elevations above 10,000 ft. (3,048 m): A 4% reduction of the burner B.T.U. rating is required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing: The dryer must be disconnected from the gas supply piping system during pressure testing at pressures greater than 1/2 psi (3.5kPa).

Exhaust System Requirements:

The dryer must be exhausted to the outdoors. It shall not be exhausted into any gas vent, chimney, wall, ceiling, attic, crawl space, or concealed space of a building.

Ducting:

If your current exhaust is plastic or metal foil flexible ducting, replace it with rigid metal ducting.

Use only 4” (10.2 cm) diameter rigid metal ducting.

When making turns, use 45° elbows rather than 90° elbows for better airflow.

All joints should be tight to avoid air leaks. Use clamps or duct tape to connect and seal all joints. Do not use screws that extend into the duct.

Avoid running the exhaust through an unheated area or vertically through a roof.

Avoid sagging or crimping the exhaust system.

Do not screen the end of the exhaust system. Use an approved exhaust hood.

The total length of flexible metal duct shall not exceed 2.4 m (7.8 ft).

The installation must conform to current Manufactured Home Construction and Safety Standard, Title 24 CFR-Part 3280 or the Canadian Manufactured Home Standard CAN/CSA-Z240 MH.

Special provisions must be made for outside makeup air. The opening should be at least twice as large as the dryer exhaust outlet.

If the dryer is exhausted through the floor and into an enclosed area beneath the mobile home, the exhaust system must terminate outside the enclosure with the termination securely fastened to the mobile home structure.

For Gas Dryers Only: The dryer must be fastened to the floor using a mobile home installation kit. Follow the instructions supplied with the kit.

1. Remove all packing materials. This includes the foam base and all adhesive tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packing, tape or printed materials before using the dryer.

1. Remove the screw securing the terminal block access cover, located on the back of the dryer’s upper corner.

2. Insert a UL listed strain relief into the mounting bracket hole and tighten it just enough to hold the two halves together.

3. Insert the power cord into the strain relief, ensuring the wire insulation is inside the strain relief.

4. Connect the power cord wires based on your home’s receptacle type:

For a 4-wire power cord (NEMA 14-30 type):

A1. Remove the green ground screw connecting the neutral-ground jumper wire to the cabinet and center terminal block screw, then discard the jumper wire.

A2. Attach the power cord ground wire (green) to the cabinet with the green ground screw. Tighten securely.

A3. Attach the power cord neutral wire (white) with the center terminal block screw. Tighten securely.

A4. Attach the remaining 2 power cord line wires (red and black) with the outer terminal block screws. Tighten both screws securely.

For a 3-wire power cord (NEMA 10-30 type):

B1. Attach the power cord neutral wire (white) to the center terminal block screw, which should still have the neutral-ground jumper wire (green) attached. Tighten the screw securely.

B2. Attach the remaining 2 power cord line wires (red and black) with the outer terminal block screws. Tighten both screws securely.

5. Tighten the strain relief screws.

6. Ensure no wires are touching the dryer drum.

7. Reinstall the terminal block cover.

NOTE: Apply a pipe-joint compound that is resistant to LP gas to all male threads. Do not use plumber’s tape.

1. Turn the gas supply off by moving the shutoff valve to the closed position.

2. Disconnect and discard the old flexible gas connector. Replace with a new CSA(AGA) approved flexible gas connector.

3. Remove the shipping cap from the gas inlet pipe at the rear of the dryer.

4. Connect a ” NPT elbow to the gas inlet pipe on the dryer. Then connect a flare adapter to the elbow. Use a pipe wrench to keep the dryer gas inlet pipe from twisting.

5. Connect the dryer to the gas supply line with a flexible gas connector.

6. Tighten the flexible gas connector using two adjustable wrenches.

7. Turn the gas supply on by moving the shutoff valve to the open position (handle is parallel to the gas pipe).

8. Check all connections for leaks by applying a noncorrosive leak-detection solution. Bubbles will identify leaks. If leaks are found, close the shutoff valve, retighten the joint, and check again. Never use an open flame to test for gas leaks.

Step 3 – Connect to an Exhaust System

1. Make sure the exhaust system is free and clear of old lint accumulation.

2. Use 4″ (102 mm) rigid or flexible metal ducting to connect the dryer exhaust outlet to the exhaust system.

3. Use clamps to seal and secure all joints. Do not connect with screws which extend into the interior of the duct.

Step 4 – Level the Dryer

1. Place the dryer in its final location, taking care not to crush or kink the exhaust vent.

2. Using a carpenter’s level, check that the dryer is level from side to side and from front to back.

3. If the dryer is not level, adjust the leveling feet. Turn clockwise to extend (raise) or counterclockwise to retract (lower) the dryer.

1. Plug the dryer power cord into an appropriate outlet.

2. Resume power to the outlet. Check that the circuit breaker is switched on.

3. Dispose of/recycle all packaging materials.

4. Make sure the dryer area is clean and free from combustible materials, gasoline, and other flammable vapors. Ensure nothing obstructs the flow of combustion and ventilation air.

5. Test dryer operation by selecting a Timed Dry heated cycle. For gas dryers, the gas line may need to be bled of air. If the burner does not light within 45 seconds, turn the dryer to “OFF”, wait 5 minutes, and try again.

Cycle Status Indicators: These lights indicate the stages of the selected cycle. The active stage blinks. The Clean Lint indicator will blink when the dryer is turned on as a reminder.

Power Button: Use to turn the dryer on and off. The dryer will automatically turn off after about 5 minutes of inactivity.

Dry Level Button: Adjusts the dryness level of automatic cycle programs. This works with automatic cycles only.

Cycle Selection Knob: Turn to select a cycle.

Automatic Cycles:

Sanitize: For sanitizing items like towels and bedding. High heat.

Heavy Duty: For high-temperature heat and heavyweight fabrics like towels and jeans.

Normal: For medium-temperature heat and cottons/linens.

Eco Dry: Similar to Normal but uses slightly lower temperature to save energy.

Perm Press: For low-temperature heat and wrinkle-free fabrics.

Delicate: For extra-low heat to gently dry delicate items.

Timed Dry Cycles:

Timed Dry: Runs the dryer for a specific amount of time.

Quick Dry: A 20-minute timed cycle for a few items.

Touch Up: A 10-minute timed cycle for refreshing clean clothes.

Air Dry: Dries with no heat for foam, rubber, plastic, or heat-sensitive fabrics.

Start/Pause Button: Press to start or pause an operating cycle.

Dry Temp Button: Selects a dryer temperature for timed dry cycles only. The No Heat setting is not available with an automatic cycle.

Wrinkle Saver Button: After the cool down cycle, the dryer will periodically tumble for 1 hour to prevent wrinkles. Use this button to extend the feature to 150 minutes or to turn it off.

Estimated Time Remaining Display: Shows the estimated total time for a dry cycle in minutes and counts down. Error codes will also be shown here if a malfunction occurs.

Timed Dry Adjust Buttons: Adjusts the length of a timed dry cycle from 10 to 95 minutes in 5-minute increments.

Cycle Signal Button: Adjusts the volume of control panel beeps and the end-of-cycle signal.

Damp Signal Button: Alerts you when clothes are approximately 80% dry, useful for removing items to be ironed. If the cycle signal is turned off, the damp signal will still sound.

NOTE: Shaded boxes indicate the default settings for each cycle.

The humidity sensor enables the dryer to sense the actual moisture content of garments in the load. Automatic Cycles utilize this information along with air temperature readings to complete the dry cycle at the proper time. This intelligent technology saves energy, reduces static, and protects clothing from damage due to over-drying.

The sensor also provides consistent and accurate drying results and enables you to fine tune the dryer’s performance with the Dry Level button.

Step 1 – Prepare and Sort Laundry

Check garment labels for manufacturers’ drying instructions.

Where possible, turn pockets inside out for uniform drying.

Tie strings and sashes so they don’t tangle.

Close zippers, snaps and hooks to avoid snagging.

Make sure buttons and ornaments on the clothes are high temperature resistant and will not damage the drum surface.

To avoid permanently setting stains or soils, check that all stains have been removed during the wash cycle. If not, wash them again.

To avoid entanglement, small articles should be collected in a mesh bag before loading.

Separate fabrics that attract lint from fabrics that give off lint.

Step 2 – Clean the Lint Screen

1. Clean the lint screen before each use by pulling on the handle inside the dryer door.

2. Use your fingers to roll the accumulated lint off of the lint screen. Do not rinse or wash the screen to remove lint.

3. Slide the lint screen back into place.

Step 3 – Load the Dryer

1. Load damp garments loosely into the dryer drum. Do not pack the dryer full.

2. An appropriate load should be ⅓ to ½ of the drum volume.

3. When drying large bulky items, only load 2-3 pieces at a time with a few small and medium-sized garments.

4. Close the dryer door.

Step 4 – Start the Dryer

1. Turn the dryer on by pressing the POWER BUTTON.

2. Select a dry cycle by rotating the CYCLE SELECTION KNOB.

3. Modify the default settings and options if desired.

4. Press the START/PAUSE BUTTON to start the dryer.

Cleaning and Maintenance

Only use a damp or sudsy cloth for cleaning the control panel.

If you spill liquid/powdered softener, bleach or detergent on the cabinet, wipe it immediately to avoid damage to the finish.

Do not use abrasive cleansers, harsh chemicals, ammonia, chlorine bleach, concentrated detergent, or solvents to clean the dryer.

Do not use any type of spray cleaner when cleaning the dryer interior. If the drum becomes stained, clean it with a damp cloth.

Washing the Lint Screen

Laundry detergent and fabric softener residue can build up on the lint screen, causing longer drying times. Wash the lint screen every 6 months, or sooner, if it becomes clogged.

1. Remove the normal accumulation of lint with your fingers.

2. Wet both sides of the lint screen with hot water.

3. Apply liquid detergent with water and scrub with a nylon brush.

4. Thoroughly rinse the lint screen with hot water.

5. Completely dry the lint screen before reinstalling.

Removing Accumulated Lint

Inside the Dryer Cabinet: Lint should be removed every 2 years, or more often, depending on usage. This should be done by a qualified person.

The Exhaust System: The exhaust system should be inspected and cleaned at least every 12 months with normal usage.

The dryer is equipped with a long-lasting LED light. If it stops operating, contact a certified technician for replacement. Replace with a 1W LED, T7 Shape, Intermediate (E17) Base, 120-volt appliance bulb ONLY.

1. Disconnect power, or unplug the dryer.

2. Open the dryer door. The light is located inside the drum above the door opening.

3. Using a Phillips screwdriver, remove the screw from the Clear Light Cover.

4. Remove the Clear Light Cover by rotating it forward and lifting it off of the two Housing Tabs.

5. Turn the light bulb counterclockwise to unscrew.

6. Replace the bulb with the specified 1W LED bulb.

7. Replace the Clear Light Cover and secure it with the screw.

8. Reconnect power, or plug in the dryer.

Vacationing Precautions

Unplug the dryer from the electrical outlet or disconnect the power.

Wash the lint screen.

For gas dryers only: Close the shutoff valve in the gas supply line.

Moving or Storage Preparation

In addition to the vacation precautions, complete these steps:

Disconnect the dryer from the exhaust system.

Turn the leveling feet so they are fully retracted into the dryer cabinet.

Use masking tape to secure the dryer door.

Move and store your dryer in an upright position only.

For gas dryers, turn off the gas being supplied to the dryer. Disconnect the dryer from the gas supply line and remove fittings attached to the dryer’s gas inlet pipe. Cap the gas supply line.

When the dryer senses an error, all operations will stop, a series of 4 beeps will sound, and an error code will be shown.

Check that the dryer is plugged in. The plug may have come loose.

Check that the electrical wall receptacle is of proper voltage. Electric dryers require a 240-volt power supply.

Check if the circuit breaker needs to be reset, or if the fuse needs to be replaced.

Check that the dryer door is firmly closed.

Dryer may be overloaded. Wet clothes should not fill more than ½ of the drum volume.

Check the exhaust ducting and exhaust hood. The entire exhaust system should be free of obstructions.

The exhaust system should be maintained, and cleaned regularly.

The dryer load may need to be sorted. Heavyweight clothes should be separated from lightweight clothes.

Bulky items may require repositioning.

Check the lint screen. The lint screen should be cleaned before each load.

Check that the dryer is not set on the Air Fluff (no heat) temperature setting.

For gas dryers, check that the gas supply line is open.

Rattling or clanking noises:

Foreign objects may be in the dryer drum. Stop the dryer and check for foreign objects such as loose change, keys, and heavy objects.

Vibration noises:

The load may be uneven. Stop the dryer and rearrange the load.

The dryer may not be level. Check that all four leveling feet are resting firmly on the floor and that the dryer is level.

Static:

Caused by over-drying. Adjust for shorter drying time and use a fabric softener or a dryer sheet.

Loads are wrinkled:

The load may have been left in the dryer too long at the end of the cycle. Be sure to remove clothes promptly after the load ends.

The dryer may be overloaded. The dryer drum should be at most half full.

Odors:

Wet clothes left in the washer and/or dryer may develop an odor. Drying will not remove this odor. Rewash clothes before drying them.

The electric heating element may have an odor when the dryer is used for the first time. The odor will be gone after the first cycle.