GULIKIT ELVES 2 PRO (01) PDF Document

Connect the controller using the USB-C port. During charging, the charging indicator light will be orange. When the GULIKIT ELVES 2 PRO is fully charged, the indicator light will turn green.

When there are special settings configured, the indicator light will be blue. When there are no special settings configured, the indicator light will be white. If the battery is low, the indicator light will flash, and the vibration function will automatically turn off. Vibration will turn back on once the battery level is restored.

To power on the controller, you can press any of the following buttons: A, B, X, Y, or the Home button.

The controller will automatically power off after 15 minutes of inactivity. To manually turn off the controller, press and hold the Home button for 10 seconds. Alternatively, you can press the OFF button located on the back of the controller.

Note that the controller will not automatically power off when using the full-auto Continuous Fire or the Auto Pilot Gaming replay function.

In the power-on state, place the controller on a flat surface. Simultaneously press the +, -, D-pad Left, and A buttons. This initiates an automatic calibration of the gyroscope. Once calibration is complete, the controller will vibrate once as a notification. If the gyroscope is functioning normally, there is no need for calibration.

With the controller in the power-on state, simultaneously press the L, R, D-pad Left, and A buttons for 6 seconds. During calibration, fully move the left and right joysticks in complete circles for 2 to 3 times. Once the calibration is complete, the controller will vibrate once and automatically exit calibration mode.

Bluetooth pairing provides a 170Hz Polling Rate and requires the computer to have Bluetooth functionality.

1. Switch the controller to the PC mode (Windows logo icon).

2. Long-press the pairing button for 2 seconds. The indicator light will start blinking quickly to indicate pairing has started.

3. On your computer, open Bluetooth settings, search for new devices, and add the GuliKit Controller device.

4. The interface will display Connected once the pairing process is complete.

A wired connection provides a 1000Hz Polling Rate.

1. Set the controller mode to PC mode (Windows logo icon).

2. Connect one end of the provided data cable to the controller and the other end into a USB A port on your computer.

3. If using a desktop computer, it is recommended to plug the cable into one of the USB ports on the back of the computer case for a more stable connection.

1. Switch the controller to the iOS mode (indicated by the iOS/Apple icon).

2. Long-press the pairing button for 2 seconds until the indicator light blinks quickly.

3. Search for devices in your device’s Bluetooth settings and select Xbox Wireless Controller.

4. The interface will show Connected once the process is finished.

Method 1 (Wireless):

1. Enter the controller settings page on the Switch console.

2. Set the controller to Switch mode (Switch icon) and long-press the pairing button for 2 seconds. The indicator light will blink quickly.

3. The console interface will display the connection to the new controller once complete.

Method 2 (Wired/Docked):

1. Set the controller to Switch mode and connect it to the Switch dock using the provided USB cable.

2. Place the Switch console on the dock. The controller will pair automatically.

3. Once successful, you can unplug the cable to use it wirelessly or leave it plugged in for wired mode.

The APG function allows you to record and repeat button presses and joystick movements using the APG button (Double-Square icon).

Recording Process:

Hold the APG button for 3 seconds. A short vibration indicates recording has started. All subsequent actions will be recorded for up to 10 minutes. To stop, press the APG button again or wait for the 10-minute limit. A long vibration indicates recording is complete.

Replay Process:

Press the APG button once briefly to replay the actions one time. Double-click the APG button to repeat the actions continuously until interrupted. You can still use the joysticks for movement during replay. To cancel midway, press any button except the joysticks.

1. Hold the Setting button (Gear icon) and press the APG button to enter read/write mode.

2. Insert the USB data cable into your computer. A USB drive named GuliKit dat will appear.

3. Open the drive to find Auto.apg, which is the recording file. You can copy this for backup or sharing.

4. To overwrite the existing recording, replace the Auto.apg file with a new one in the USB drive.

5. Once the writing process is complete, the controller will automatically power off. Do not change the file name.

All special functions require holding the Setting button (Gear icon) while pressing the specific buttons listed below:

Note: L3 and R3 refer to pressing down on the joysticks. Each joystick can be configured individually for sensitivity.