Free English GUDE GRP 50 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD GUDE GRP 50 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I assemble the handle and transport wheel for the GUDE GRP 50 plate compactor?
Step 1: Fold the handle up (1).
Step 2: Rotate the handle mounting bolts to secure them (2).
Step 3: Attach the transport wheel using the axle bolt, washers, and nuts provided (3).
What type of oil should be used for the engine of the GUDE GRP 50 plate compactor, and what is the required oil level?
The engine requires 10W-40 motor oil.
The oil level must be checked using the dipstick; ensure the level is between the MIN and MAX marks (Max 400 ml).
What is the recommended procedure for checking and topping up the engine oil in the GUDE GRP 50 plate compactor?
Step 3: Wipe the dipstick clean.
Step 4: Remove the dipstick and check the level by gently rocking the unit.
Step 5: Check that the oil level is between MIN and MAX (Max 400 ml).
Step 6: If necessary, pour 10W-40 oil into the engine until the level is correct.
Step 7: Reinsert the dipstick and check the level again.
Step 8: The oil level must show a mark between MIN and MAX.
What type of fuel should I use for the GUDE GRP 50 plate compactor?
Unleaded petrol should be used. The tank capacity is 1.6 liters.
What is the safe operating procedure for starting the GUDE GRP 50 plate compactor?
Step 1 (Preparation): Ensure the unit is on a firm, flat surface and clear of obstacles. Ensure the work area provides sufficient clear space (minimum 3.00 m clearance is indicated for safe operation).
Step 2 (Fuel/Ignition): Ensure fuel cap is closed/locked. Ensure the engine switch is set to ON.
Step 3 (Choke/Throttle): Set the throttle/choke lever according to conditions.
Step 4 (Start): Pull the starter cord to start the engine.
Step 5 (Post-Start): Adjust the choke/throttle settings as required once the engine is running.
How do I stop the GUDE GRP 50 plate compactor?
Turn the engine control switch to the OFF position.
What maintenance steps are required for the belt system on the GUDE GRP 50 plate compactor?
Step 1: Remove the guard/cover bolt (1).
Step 2: Remove the tensioner/guide roller bolts (4x) (2).
Step 3: Inspect the belt tension. The deflection should be approximately 8 mm (3). If replacement is needed, use the new belt and ensure the tensioner bolts are secured (4, 5).
What is the procedure for checking or replacing the spark plug on the GUDE GRP 50 plate compactor?
Step 1: Ensure the engine is cool and the ignition switch is OFF. Remove the spark plug wire.
Step 2: Remove the spark plug using the special tool (5).
Step 3: Clean the spark plug using a brush (3).
Step 4: Inspect the spark plug gap, which should be set to 0.6-0.8 mm (4).
Step 5: Reinstall the cleaned or new spark plug (5).
What is the correct procedure for cleaning the air filter on the GUDE GRP 50 plate compactor?
Step 1: Disassemble the air filter housing to access the filter elements (1).
Step 2: Clean the paper filter element using compressed air only. Never use water to clean the paper filter (2).
Step 3: Reassemble the air filter housing (3).
What are the required safety precautions regarding the work site when operating the GUDE GRP 50 plate compactor?
Read and understand the operating instructions before using the appliance.
Familiarize yourself with the control elements and how to use the appliance properly.
Abide by all the safety measures stated in the service manual.
Act responsibly toward third parties.
The operator is responsible for accidents or risks to third parties.
Always place the unit on a firm and flat surface, ensuring the machine does not tip over, slide, or fall during use.
Maintain enough distance from the secured edges of the construction pit as well as any embankments.
The machine must never be used on a slope.
Do not work with the unit in an environment with a risk of explosion where there are flammable liquids, gases, or dust.
The machine must never be used in deep pits, tunnels, or caves (greater than 1.5 m).
The work site must be free of electric cables, gas, and water lines that could sustain damage from the vibrations.
Keep children and bystanders away while operating. The minimum safe distance is 5 meters.
What steps should be taken if the engine of the GUDE GRP 50 plate compactor does not start?
| Failure | Cause | Removal |
|---|---|---|
| The GUDE GRP 50 engine does not start. | Fuel tap closed | Make sure the fuel tap and On/Off switch are in the “ON” position. |
| The GUDE GRP 50 engine does not start. | Lack of fuel | Add some fuel. |
| The GUDE GRP 50 engine does not start. | Weak tension on the starter | Pull strongly the starting cord. |
| The GUDE GRP 50 engine does not start. | Wrong fuel, storing without petrol tank being drained, wrong fuel type | Drain the fuel tank and carburetor, add fresh petrol. |
| The GUDE GRP 50 engine does not start. | Sooted spark plug (carbon residues on electrodes), electrode distance too big | Clean the spark plug, check the plug thermal value, possibly change the plug, set the electrodes distance to 0.6-0.8 mm. |
| The GUDE GRP 50 engine does not start. | The spark plug is wet from petrol (over-saturated engine). | Dry the spark plug out and refit it. |
| The GUDE GRP 50 engine does not start. | Little oil in the engine / Low oil level signaled | Add oil / Place the unit in a horizontal position. |
| The GUDE GRP 50 engine does not start. | Choke has not been used | Use the choke. |
What should be checked if the engine of the GUDE GRP 50 plate compactor runs irregularly?
| Failure | Cause | Removal |
|---|---|---|
| The GUDE GRP 50 engine runs irregularly. | Problem with ignition | Make sure the spark plug is fitted properly. Make sure the spark plug cable is on the spark plug. Clean the spark plug and check the correct electrode distance. |
| The GUDE GRP 50 engine runs irregularly. | Wrong fuel | Make sure the correct fuel grade was used. |
What is the required inspection and maintenance schedule for the GUDE GRP 50 plate compactor engine oil and eccentric oil?
| Regular Servicing Period | Before Any Start-up | After 1 Month or 20 Hours of Operation | After 3 Months or 50 Hours of Operation | After 6 Months or 100 Hours of Operation | After 200 Hours of Operation |
|---|---|---|---|---|---|
| Engine oil (Control) | ✓ | ✓ | ✓ | ||
| Engine oil (Change) | ✓ | ||||
| Eccentric oil (Change) | ✓ |
What is the required inspection and maintenance schedule for the fuel/exhaust systems and starter cord on the GUDE GRP 50 plate compactor?
| Regular Servicing Period | Before Any Start-up | After 1 Month or 20 Hours of Operation | After 3 Months or 50 Hours of Operation | After 6 Months or 100 Hours of Operation | After 200 Hours of Operation |
|---|---|---|---|---|---|
| Petrol hose, Exhaust system, Choke, Cable starter (Inspection) | ✓ | ||||
| Petrol hose, Exhaust system, Choke, Cable starter (Clean) | ✓ | ✓ |
What is the required inspection and maintenance schedule for the air filter, petrol filter, and spark plug on the GUDE GRP 50 plate compactor?
| Regular Servicing Period | Before Any Start-up | After 1 Month or 20 Hours of Operation | After 3 Months or 50 Hours of Operation | After 6 Months or 100 Hours of Operation | After 200 Hours of Operation |
|---|---|---|---|---|---|
| Air filter (Clean) | ✓ | ✓ | |||
| Air filter (Change) | ✓ | ||||
| Petrol filter (Clean) | ✓ | ✓ | |||
| Spark plug (Inspection) | ✓ | ||||
| Spark plug (Clean) | ✓ |
What materials is the GUDE GRP 50 plate compactor exclusively intended for compressing?
The GUDE GRP 50 plate compactor is exclusively intended to be used for compressing small to medium areas, foundations, terraces, pavements, and driveways made of the following materials:
Sand, shingle, gravel, crushed stone, asphalt, low-cohesive mixing materials.
When using a rubber mat, it can be used for paving stones and bricks.
What personal protective equipment (PPE) is required when operating the GUDE GRP 50 plate compactor?
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection should be worn, depending on the conditions and intended use of the appliance, to reduce personal injuries.
What precautions must be taken regarding the terrain when operating the GUDE GRP 50 plate compactor?
Always place the unit on a firm and flat surface.
Ensure that the machine does not tip over, slide, or fall during use.
Maintain enough distance from the secured edges of the construction pit as well as any embankments.
The machine must never be used on a slope.
Check carefully the terrain where the appliance is being used and remove any items that could get caught and be thrown away.
CLICK HERE TO DOWNLOAD GUDE GRP 50 (01) PDF DOCUMENT