GPO PCD299 (01) PDF MANUAL

GPO PCD299 (01) PDF SUMMARY:

How do I listen to the radio?

1. Turn the function selector switch to the RADIO position.
2. Select the desired band by using the “BAND” selector.
3. Adjust the radio frequency to your desired station by using the “TUNING” control.
4. Adjust the “VOLUME” control to the desired level.

How do I set the FM / FM-Stereo reception?

Set the “BAND SELECTOR” to select the MONO(FM) or STEREO(FM ST.) mode for FM reception. The Stereo indicator will light up to show FM ST. mode when FM-Stereo reception is available.

How do I play cassettes?

1. Turn the function selector switch to the OFF/TAPE position.
2. Press the STOP/EJECT button to open the cassette compartment.
3. Insert a recorded audio cassette into the compartment with the tape opening facing upwards and the side you wish to listen to facing the front (full spool to the right). Then close the cassette compartment again.
4. Press the PLAY key to listen to the tape.
5. With the STOP/EJECT key you can stop play-back.
6. Wind the tape forwards or backwards if necessary in the direction of the arrow keys F.FWD = forwards, RWD = reverse.
7. Always press the STOP/EJECT key when changing the direction or stopping the tape. This prevents damage to the machine and the tape.
8. If the STOP/EJECT button is pressed again the flap of the cassette compartment opens.
9. In order to interrupt playback briefly, press the PAUSE button. Pressing again continues playback.

How do I record cassettes?

1. Insert an audio cassette with the side on which you wish to record facing forwards (full reel on the right). Ensure that the cassette is not copy-protected (the copy protection tab on the top narrow side of the cassette must not have been removed).
2. Select the source from which you wish to record with the function switch and then start playback from this source if necessary. The sound source which you are listening to is the one from which the recording is made. The recording level is controlled automatically. Changing the volume does not change the recording.
3. Please press the “RECORD” button(the PLAYBACK button is automatically pressed down at the same time). Recording now begins. All previous recordings are automatically erased.
4. The recording can be interrupted briefly using the PAUSE key, or stopped by means of the STOP/EJECT button.

How do I play a CD?

1. Set the “FUNCTION” selector to “CD” mode.
2. Open the CD door and place a CD disc with the label up on the CD compartment.
3. Close the CD door.
4. Focus search is performed if disc is inside. Total number of tracks is read and appears on the display.
5. Press the “PLAY / PAUSE” button to start playing the CD.
6. Adjust the “VOLUME” control to the desired level.
7. Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
8. In order to remove a CD, please press the “STOP” button, open the CD compartment and lift the CD out carefully.

Always keep the CD door closed.

What happens if a disc is inserted the wrong way around, respectively if no disc is inserted?

“No“ appears on the display.

How do I program a CD to play desired sequence of tracks?

Up to 20 tracks for CD can be programmed for disc play in any order. Be sure to press the “STOP” button before use.

1. Press the “PROGRAM” button, the display will show “01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button.
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to play the disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.

What is the function of the repeat button during CD playback?

Press the “REPEAT” button before or during playing CD disc, each press switches the mode function as follows:

1 – REPEAT

2 – REPEAT ALL

3 – NORMAL PLAYBACK

How do I perform cleaning and maintenance?

• Always remove the mains plug before cleaning the machine.
• Any marks on the surface can be wiped off with a slightly damp cloth without any additives.