GAGGENAU VR 414 610 (01) PDF MANUAL

The safety definitions for the GAGGENAU VR 414 610 are as follows:

WARNING: This indicates that death or serious injuries may occur as a result of non-observance of this warning.

CAUTION: This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.

Note: This alerts you to important information and/or tips.

WARNING: Before you plug in an electrical cord or turn on the power supply, make sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian Electrical Code), the GAGGENAU VR 414 610 must be installed on a separate branch circuit.

WARNING: Risk of electrical shock or fire

Frame grounded to neutral through a ground strap. Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor.

For installations where grounding through the neutral conductor is prohibited:

a) disconnect the link from the neutral,

b) use grounding terminal or lead to ground unit,

c) connect neutral terminal to lead branch circuit neutral in usual manner (when the appliance is to be connected by means of a cord kit, use a UL listed 4-conductor cord for this purpose).

Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections, and grounding must comply with all applicable codes. Before installing, turn power OFF at the service panel. Lock the service panel to prevent power from being turned ON accidentally. The installer should show the owner the location of the circuit breaker or fuse and mark it for easy reference.

Appliance Handling Safety: Hidden surfaces may have sharp edges. Use caution when reaching behind or under the appliance.

Appliance Construction: Never modify or alter the construction of the appliance. For example, do not remove leveling legs, panels, wire covers, or anti-tip brackets/screws.

Repairs: Do not repair, replace or remove any part of the GAGGENAU VR 414 610 unless specifically recommended in the manuals. Improper installation, service, or maintenance can cause injury or property damage. Refer to the manual for guidance. All other servicing should be done by an authorized servicer.

Overhead Cabinets: To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a hood that projects horizontally a minimum of 5 inches (127 mm) beyond the bottom of the cabinet. Verify that cabinets above the cooktop are a maximum of 13″ (330 mm) deep.

Packaging: Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material.

We strongly recommend the installation of a ventilation hood above the GAGGENAU VR 414 610. The hood must be installed according to the instructions furnished with the hood.

CAUTION: The appliance should not be installed with a ventilation system that blows air downward toward the burners. This type of ventilation system may cause ignition and combustion problems with the gas cooking appliance resulting in personal injury or unintended operation.

Yes. This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:

STATE OF CALIFORNIA PROPOSITION 65 WARNING:

WARNING: Cancer and Reproductive Harm.

The following tools and parts are needed:

Screwdriver Torx T20

Pencil

Drill with 1/4″ (6 mm) bit

Jigsaw

Tape Measure

Note: Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer.

The minimum spaces that must be maintained when installing the GAGGENAU VR 414 610 electric grill shall be:

A: minimum 30″ (762 mm)

B: minimum 8″ (200 mm)

C: minimum 1 9/16″ (40 mm)

D: Stainless steel work surfaces: both work surfaces must be permanently fitted on both sides of the grill to protect the countertop when the grill is installed separately. When installed next to another Vario appliance, a work surface must be fitted on the opposite side to protect the countertop. When installed between two other Vario appliances, no work surface is required.

E: maximum 13″ (330 mm)

Countertop Requirements:

WARNING: To reduce the risk of ignition of surrounding combustible materials, install at least 2″ (51 mm) from both sidewalls and the rear wall.

The countertop must be level and horizontal, and its stability must be maintained after the cut-out is made.

Solid surface countertops often require special installations like heat-reflective tape and rounded corners. Contact your countertop manufacturer for specific instructions.

Installation Space Preparation:

The kitchen unit must be heat-resistant to at least 200° F (90°C). The cut edges must be flat and at a 90° angle to the countertop. Seal cut surfaces to make them heat-resistant and watertight. Maintain a minimum gap of 3/8″ (10 mm) from the underside of the appliance to kitchen units. Use suitable base constructions for load-carrying capacity, especially for thin countertops.

Standard Cut-out Dimensions:

Cut-out width: 14 3/16″ ±1/16 (360 ±2 mm)

Cut-out depth: 19 3/8″ ±1/16 (492 ±2 mm)

Minimum distance to sidewalls: 2″ (51 mm)

Minimum distance from countertop front edge to cut-out: 23 5/8″ (600 mm)

Minimum distance from cut-out to rear wall: 3/4″ (20 mm)

Flush mounting is possible in temperature- and water-resistant countertops such as stone, plastic (like Corian®), or solid wood (consult manufacturer and seal edges). Installation in particleboard is not possible.

Flush Mount Cut-out Dimensions:

Cut-out width: 20 11/16″ (526 mm)

Cut-out depth: 19 3/8″ ±1/16 (492 ±2 mm)

Corner radius: r 3/16″ (5 mm)

Step depth: 1/8″ (3.5 mm)

Minimum distance to sidewalls: 2″ (51 mm)

Any cut-out work must be performed in a workshop according to the installation diagram. The cut-out must be clean and precise. Clean and degrease the cut-out edges with a suitable cleaning agent.

Note: Only install the appliance in conjunction with the corresponding control console.

1. Remove the packaging of the control knobs and the protective film from the light rings.

2. Open the cover of the terminal box on the control console. Secure the mains connecting lead as shown in the terminal diagram and secure it with pull relief. Close the terminal box cover.

3. Hold the retaining plate against the front panel from behind. Stick the control knobs into the holes from the front and screw it tight from behind with the nuts. Make sure that the control knobs are correctly arranged.

4. Screw the control console tight to the retaining plate using the nuts included.

1. Firmly plug in the connecting lead from the appliance and the control console. The plugs must engage with a “CLICK”.

2. Evenly insert the unit in the cut-out. Press the unit firmly into the cut-out from above. The unit must sit firmly and not move. If necessary, secure strips at the sides in the cut-out if the cut-out width is at the top tolerance limit.

3. Connect the appliance to the mains and check that it is working. If both illuminated rings behind the control knobs flash alternately, the connecting cable between the control console and the appliance is not plugged in. Check that the connecting cable is fitted correctly.

4. Flush installation only: It is imperative to test functioning before jointing! Joint the surrounding gap with a suitable, temperature-resistant silicone adhesive (such as OTTOSEAL® S 70). Smoothen the seal joint with a recommended smoothing agent. Do not operate the appliance until the silicone adhesive has dried completely (at least 24 hours). NOTICE: Unsuitable silicone adhesive used on natural stone worktops will cause permanent discoloration.

5. Remove lava stones from the plastic film and place them in the lava stone trough.

6. Insert the grease tray and the lava stone trough in the appliance.

7. Fold the grill heating elements down.

8. Fit the cast iron wire racks.

The branch-circuit breakers ampacity, wire sizes, and connections must conform to the requirements of the National Electrical Code or Canadian Electrical Code and all local codes and ordinances. The mains connecting cable must at least correspond to the type SJTO 3×16 AWG 105°C and must be purchased through and connected by an authorized specialist.

Hard-Wired Connection:

Attach flexible conduit to the junction box. Connect the lead wires to the junction box supply wires in the proper phase:

black (L1) to black

red (L2) to red

green to ground

Connection with a Plug:

The plug has to conform with NEMA CONFIGURATIONS FOR PLUGS AND RECEPTACLES.

The appliance must be properly grounded.

The plug must be rated not less than type 6-20 P (2-pole 3-wire grounding).

Only a qualified electrician should connect the plug.

Install a socket outlet earthed in accordance with regulations approx. 27″ (700 mm) above the floor behind the appliance. The socket outlet must still be accessible after installation.

WARNING: Before you plug in an electrical cord or turn on the power supply, make sure all controls are in the OFF position.

1. Remove everything from the cooktop surface.

2. Switch on the circuit breaker.

3. Verify that the elements function properly.

First, disconnect the appliance from the power supply. For flush-mounted appliances, remove the silicone joint. Then, push the appliance out from below.

CAUTION: Damage to appliance! Don’t lever the device out from above at the frame.

When you call for service, please indicate the product number (E-Nr.) and serial number (FD-Nr.) so that you can be supported in a qualified manner. You will find the type plate with these numbers on the bottom of the appliance.

Please note that failure to follow the installation, use, and care instructions may result in a service call that is not covered by the appliance warranty, as it may be for customer education rather than fixing a mechanical issue.

REF	Components
A1	Control panel pcb
A1-Rel1	Relay (bistable)
A1-Rel3	Relay heater (front zone)
A1-Rel5	Relay heater (rear zone)
A1-SW1	Pre selection switch (rear zone)
A1-SW2	Pre selection switch (front zone)
A1-TR1	Transformer
E1	Heating element front (1500W / 230V)
E2	Heating element rear (1500W / 230V)
F1	Temperature limiter front zone (T120)
F2	Temperature limiter rear zone (T120)
S1	Micro switch (E2 position)
X1	Mains terminal
X2	Plug socket connector 7 pole