FURRION DV7100 (01) PDF MANUAL

FURRION DV7100 (01) PDF SUMMARY:

How do I mount the unit?

Choose a mounting location away from humid areas, water sources, appliances, or any equipment that can radiate heat. Select an area on a wall or cabinet free from cable, fuel, or brake lines, and ensure the area behind the DV7100 has a vent hole or adequate room around the rear of the unit for cooling. Ensure when the stereo is mounted in the cutout, the wires at the rear of the unit are not pressed against the heat sink. Before finally installing the unit, connect the wiring temporarily and make sure the unit and the system work properly. Remove the plastic frame of the front panel from the unit. Fix the unit with 4 pieces #8 pan head self-tapping screws. Put the plastic frame of the front panel back on the unit. Fix the unit with screws according to the diagram.

---

How do I turn the unit on or off?

When the unit is powered off, it may be switched on by pressing the POWER button. When the unit is switched on, press and hold the POWER button for more than 1 second to switch the power off.

---

How do I select function mode?

Press the AUX, DVD, AM/FM, HDMI, USB, or BT button on the front panel to select the corresponding mode.

---

How do I adjust the volume level?

Press the VOLUME + or VOLUME – button on the front panel to adjust the volume level during playback.

---

How do I mute or resume sound?

Press the MUTE button to eliminate or resume sound immediately during playback.

---

How do I set the sound mode and menu?

Press and hold the SEL button for more than 2 seconds to turn on BASS, then press the SEL button shortly and repeatedly to select TRE (treble), LIR (balance), EQ OFF (FLAT/CLASSIC/ROCK/POP), LOUD OFF/LOUD ON, VOL LAST/VOL DEFA(AVOL), BEEP ON/BEEP OFF, DX/LOCAL (in RADIO mode), STEREO/MONO (in RADIO mode), SUBW ON /SUBW OFF, AMERICA3/AUSTRIA/EUROPE (in RADIO mode) in sequence and circulation. After selecting a desired item, use the VOLUME+/- button to set.

---

What does the ‘BEEP ON/BEEP OFF’ setting do?

BEEP ON mode: A beep is generated when any key is pressed. BEEP OFF mode: The beep sound is disabled.

---

What does the ‘VOL LAST/VOL DEFA’ setting do?

VOL LAST: The volume level when switching off will be restored when powering on. VOL DEFA: The volume level of the main unit after power on is a constant value.

---

How do I pre-set the constant volume level after power on?

When selecting the VOL DEFA item, press the SEL button to display AVOL, then pre-set the constant volume level after power on with the VOL control.

---

What does the ‘DX/LOCAL’ switch do in radio mode?

The DX/LOCAL switch divides the radio station search mode and controls an attenuator in the tuner during the search. The detecting level of seek, scan, and auto-memory will be reduced as much as the attenuated level of the tuner. In radio mode, press the LOC button to change local reception or distance reception. This button is only for FM reception; in AM mode, LOC is invalid.

---

How do I display and adjust the time?

Press and hold the 6 button for more than 2 seconds until the real time flashes on the display. Then adjust HOUR by pressing the VOLUME +/- button, and adjust MINUTE by pressing the ||<< / >>|| button.

---

How do I adjust the backlight?

Press and hold the 5/BACKLIGHT button repeatedly to adjust the backlight.

---

How do I set the alarm function?

To set the ALARM mode on or off, press and hold the 6 button repeatedly to enter ALARM ON/OFF mode and use the VOLUME +/- button to select ALARM ON or ALARM OFF. To set the ALARM time, press and hold the 6 button repeatedly to enter ALARM time setting mode (the LCD will display the time “AM 00’00 “ but not flash), then use the ||<< / >>|| button to set the MINUTE and the VOLUME +/- button to set the HOUR.

---

How do I reset the unit?

Press RESET with a cuspidal object to reset the unit to the factory default and reinstate the correct functions. Alternatively, in AUX mode, press and hold the 2/STOP button until the LCD displays “RESET III", then press and hold the 3/RPT button to reset to the factory default.

---

How do I select a radio band?

Press the AM/FM button briefly and repeatedly to select a desired radio band in sequence and circulation as follows: –>FM1–>FM2–>FM3–>AM1–>AM2–>.

---

How do I search for a radio station manually or automatically?

Press the >>| or |<< button briefly to manually tune up/down for your desired radio stations step by step. Press and hold the >>| or |<< button for 2 seconds to automatically tune up/down for a radio station with a strong signal.

---

How do I store the current station or turn on a preset one?

To store the current station, press and hold the AM/FM button until the frequency flashes, then briefly press one of the 6 number buttons to store the current station in the preset memory bank of the number button for the current band. In this way, the unit can store 30 preset stations. To turn on a preset station, press one of the 6 number buttons briefly to turn on the preset station stored in the preset memory bank of the number button for the current band.

---

How do I auto-search and store the strongest stations?

When pressing and holding the 2/STOP button on the front panel for more than 2 seconds, the radio searches from the current frequency and checks the signal strength level until the 6 strongest stations are found. The 6 strongest stations are preset to the corresponding preset memory-numbered bank. The auto-storage operation is implemented in each selected band. When the auto-storage operation is finished, the radio executes a preset scan.

---

How do I set the frequency?

Press and hold the SEL button for more than 2 seconds to turn on BASS, then press the SEL button shortly and repeatedly until it displays one of the areas: AMERICA3, AUSTRALIA, or EUROPE. Use the VOLUME+/- button for selection and briefly press the SEL button for confirmation.

---

How do I insert or pull out a USB stick?

When needing to play back USB music, insert the USB stick. The unit will switch to USB mode and display “USB” on the LCD.

---

How do I play the previous or next track?

Press the ||<< or >>|| button briefly to play the previous or next track.

---

How do I play fast backward or forward?

Press and hold the ||<< or >>|| button to play backward or fast forward.

---

How do I play the previous or next 10th track?

Press the 5 or 6 button to play the previous or next 10th track.

---

How do I use the 1/PLAY/PAUSE button?

During playback, press the 1/PLAY/PAUSE button to pause playback. Press the 1/PLAY/PAUSE button again to play again.

---

How do I repeat tracks?

During playback, press the 3/RPT button briefly to play the current track repeatedly. Press the RPT button twice to play the tracks in the Album repeatedly. Press the RPT button three times to RPT ALL tracks, and the LCD will display ALL. Press the RPT button four times to cancel the RPT function, and the LCD will display RPT OFF.

---

How do I play tracks in random order?

During playback, press the RDM button briefly to play all tracks in random order.

---

How do I search for tracks?

Press the USB button, which will activate the TRACK SEARCH mode. The LCD will display TRACK NO (the total number of tracks in the SD card or USB stick) and flash the 0 on the biggest digit position. Use the VOLUME +/- button to select a number on the flashing digit position from 0 ~ 9. Then, press the USB button to confirm the number and flash the 0 on the next smaller digit position. With the same means, select the number on the flashing digit position with the VOLUME +/- button. After finishing selecting the numbers on all digit positions, press the 1/PLAY/PAUSE button to play the track of the selected serial number.

---

How do I pair my device via Bluetooth?

Turn on the Bluetooth mode of the mobile phone, then select the function of Finding Bluetooth Device and enter it. After finishing the finding, it will show the name of the Bluetooth Device FURRION DV7100-XXXX (where X can be any character A-Z or number 0-9), select it and enter it. For some phones, a password may be needed; in this situation, input the password “0000,” then the unit will display “BT LINK”.

---

How do I use my mobile phone to connect or disconnect via Bluetooth?

In connection status, find the paired and connected Bluetooth Device, then press the disconnection button to disconnect. In disconnection status, find the paired and disconnected Bluetooth Device, then press the connection button to connect.

---

What happens when a dialing takes place or a call is received in connection status?

The mobile phone transfers to the car audio player whenever a dialing takes place, and the mobile phone transfers to the car audio player whenever receiving a call.

---

How do I accept, reject, or end a call?

During ringing, press the TEL button to accept the call. During ringing, press the HANG UP button to reject the call. During talking, press the HANG UP button to end the call. Note: During ringing, CALL IN appears and then the phone number.

---

How do I set the talking volume level?

While talking, use the VOLUME +/- button to adjust the volume level, but this volume level cannot be saved.

---

What happens when dialing or receiving calls while the unit is in sleep mode?

When the Stereo is in sleep mode (Acc on and standby), to execute a dialing (with a mobile phone) or receive a call, the Stereo will temporarily wake up.

---

How do I play an audio file from an external Bluetooth device (mobile phone) on the DV7100?

After the device has been paired successfully and the DV7100 screen displays BT LINK, if the mobile device supports A2DP, you will be able to stream music from your Bluetooth device so it can be played by the stereo speaker. You must select on your mobile Bluetooth device to play the audio through Bluetooth. If your mobile device supports AVRCP, you will be able to control the basic phone audio output functions using the DV7100 controls, e.g., Play/Pause.

---

How do I set up my Stereo using NFC?

Turn on the NFC function of your mobile phone and make sure the screen is active and unlocked. With the NFC detection area of your phone touching the NFC detection area of the Stereo, you can connect or disconnect your mobile phone with the Stereo conveniently. Note: For the first time pair and connect, it will ask you to input a password. The password is “0000”.

---

How do I install the APP to control the stereo?

To control the unit instead of using the front panel or remote control, you can use your phone. You will need to install the “Es Control” app onto your mobile device. The app will need to be downloaded from Google Play (Android phone) or the App Store (iPhone). Do a search for “Es Control” and proceed to download. Install per the app instructions.

---

How do I use the APP to connect and control the stereo?

Open the BT function of your smartphone and pair with the Stereo. Under the BT connection, tap the “Es Control” icon to enter the APP connection interface, then select the name “FURRION DV7100-XXXX” (Android phone) or “DV7100-4.0-XXXX" (iPhone) to enter it (where X can be any character A-Z or number 0-9). Use the APP to control the Stereo freely.