FOLLETT 7UD100A (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD FOLLETT 7UD100A (01) PDF MANUAL


PDF Content Summary: Undercounter Ice and Water Dispenser with Chewblet® Ice Machine 7UC100A, 7UD100A Installation, Operation and Service Manual Serial numbers above J57179 7UC100A 7UD100A Following installation, please forward this manual to the appropriate operations person.

801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 follettice.com Order parts online: follettice.com 00966879R09

2 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Ambient Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Heat Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Detailed Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Maintenance/Cleaning Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Accessing Internal Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Filter Display Indicator Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 NSF-approved Cleaning and Sanitizing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 LED Indicator Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Evaporator Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Evaporator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Water Feed Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Bin Melt Water/Evaporator Feed/Clean Out System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Vent System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Refrigeration Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Condenser Fan Motor Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 User Interface Display Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Electrical Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Bin Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Evaporator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 3 Welcome–––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability, and outstanding after-the-sale support. To ensure that this product delivers that same degree of service, we ask that you take a moment to review this manual before beginning the installation. Should you have any questions or require technical help at any point, please call our technical service group at (877) 612-5086 or +1 (610) 252-7301. Before You Begin ––––––––––––––––––––––––––––––––––––––––––––––––––– After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, immediately notify the shipper and contact Follett Corporation so that we can help in the filing of a claim, if necessary. If needed, the serial number of your dispenser can be found by removing the drip tray ❶ and locating the serial number label ❷. A QR Code is located on the right hand side of the drip tray ❸. This code allows you to access manuals, technical bulletins, and on-line training related to the 7 Series dispensers. Scan to access technical documentation or visit follettice.com/7seriesdocs 00981100R00 2 1 3 Check your paperwork to verify that you received the correct dispenser. Follett configuration numbers are designed to provide information about the type of dispenser you are receiving. The following is an explanation of the different model numbers. 7 UC 100 A Dispenser Storage Capacity Configuration Ice machine Capacity Condenser

7 lb UC Undercounter UD Undercounter - ADA 100 lb per day A Air-cooled

Important Safety Information ––––––––––––––––––––––––––––––––––––––––– Please read and adhere to the following safety information while installing, using, or servicing your Follett 7 Series Ice Dispenser. 1. Always disconnect power before servicing the dispenser. 2. Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition. 3. Ice is food. Follow the recommended cleaning and sanitizing instructions to maintain cleanliness of delivered ice. 4 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Specifications ––––––––––––––––––––––––––––––––––––––––––––––––––––– Dimensions 7UC100A 7UD100A Width 14.55" (370 mm) 14.55" (370 mm) Depth 22.05" (560 mm) 22.05" (560 mm) Height 33.50" (851 mm) 31.50" (800 mm) Unit Shipping Weight 110 lb (50 kg) 110 lb (50 kg) Ambient Information CAUTION! The 7UC100A and 7UD100A are for indoor use only. Maximum* Minimum* Air Temperature† 100 F (38 C) 50 F (10 C) Water Temperature 90 F (32.2 C) 40 F (4.5 C) Water Pressure 70 psi 10 psi Relative Humidity 55% at 78 F (25.5 C) * Use outside of these limitations is misuse and will void warranty. † Best performance is achieved between 80 F (27 C) and 50 F (10 C). Plumbing ▪ Water Inlet: 1/4" MPT ▪ Optional Drain Accessory Kit (item# 00956375 or 00981977): 1/2" ID tubing ▪ Water shut-off recommended within 5 ft. (1.5 m) of dispenser Water WARNING! Connect to potable water supply only. ▪ Water Mineral Content: – TDS: greater than 5 ppm (mg/l) but less than 400 ppm (mg/l) – Hardness: Less than 200 mg/l (12 gpg) ▪ Not recommended for use with softened water Clearances ▪ 3" (77 mm) behind dispenser for electrical and optional drain connection. ▪ 6" (153 mm) in front of dispenser for ventilation. Electrical ▪ 115V, 60 Hz, 1 phase, 5A, maximum fuse 15A ▪ Connect to dedicated 15A circuit, fuse or breaker ▪ Must be grounded - requires 3-prong outlet. Do not remove ground. Refrigeration WARNING! Do not damage the refrigerant circuit. Refrigerant can cause personal injury and/or damage dispenser. ▪ Refrigerant R134a – 215 grams (7.6 oz.) Heat Rejection ▪ 1700 BTU/hr (498 W) Undercounter Dispenser and Ice machine 7UC100A/7UD100A 5 Specifications (continued) –––––––––––––––––––––––––––––––––––––––––––––– Detailed Drawing 14.55" (370 mm) 22.05" (560 mm) A 4.00" (102 mm)

FRONT VIEW 3.81" (97 mm) SIDE VIEW Dimension 7UC100A 7UD100A (ADA) 14.55" (370 mm)

A B C 33.50” (851 mm) 22.76” (578 mm) 22.69” (576 mm) 31.50” (800 mm) 20.76” (527mm) 20.69” (526 mm) 2.40" (61 mm)2.98" (76 mm)

power cord L2 G L1 NEMA 5-15 right angle 1/4" MPT water inlet A B C BACK VIEW

6 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Installation –––––––––––––––––––––––––––––––––––––––––––––––––––––––– CAUTION! No service or maintenance should be performed until the technician has thoroughly read this service manual. Except for routine cleaning and sanitizing, only qualified technicians should attempt to service or maintain this equipment.

1. Measure to verify that the dispenser will fit in the desired location. A clearance of at least 3" (77 mm) is required behind the dispenser for the electrical and optional drain connection. 2. Ensure that the finished floor inside the cabinet is flush (level) with the floor outside the cabinet (Fig. 1). If the cabinet floor is lower than the finished floor, the cabinet floor must be built up (using appropriate materials) until it is flush with the finished floor. A flush floor is required for proper operation and maintenance/service of the dispenser. 3. Rough-in the electrical service, water line, and optional Drip Tray Drain Kit*. Note: The dispenser must be installed such that it can be moved forward at least 4" (10.16 cm) to allow access to the Bin Lid Cleaning Spout (Fig. 9.6) for dispenser cleaning and sanitizing. Take this requirement into consideration during rough-in. ▪ Electrical: 115V, single phase, 15A receptacle required. The dispenser has an integral 8 ft. (2.4 m) cord and plug. ▪ Water: supply line (with shut-off valve) connects to the dispenser's 1/4" MPT inlet. * The optional Drip Tray Drain Kit (item# 00956375) requires a floor drain within 15 ft. (4.5 m) of the dispenser. For detailed installation instructions, please refer to the instructions shipped with the Drip Tray Drain Kit. 4. Install the angle bracket inside the cabinet,18.15" (461 mm) from the toe kick (Fig. 2.1). The bracket prevents the dispenser from being located/pushed beyond the recommended cabinet space depth. Do not attach the bracket to the dispenser. Fig. 1 floor Fig. 2 cabinet space 1 18.15” (461 mm)

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 7 Installation (continued) –––––––––––––––––––––––––––––––––––––––––––––––––

5. Connect water line. Recommended routing (Fig. 3) allows easy access to water for cleaning and sanitizing procedure. 6. If installing the optional internal water filter*, please complete the steps shown in NSF-approved Cleaning and Sanitizing Procedure on page 11 before proceeding. If not, proceed to step 10. * If your dispenser has the internal water filter option, the water filter must be installed for the dispenser to operate. Because internal components will need to Fig. 3 3' (91.4 cm) Plug Valve Fig. 4 1/4" MPT

be accessed for both procedures, Follett recommends installing the water filter just prior to initial sanitizing. 7. Lift and remove the top panel, set aside (Fig. 4.1). 8. Remove two screws (Fig. 4.2) and remove left side panel. 9. Install filter as shown. Turn filter clockwise until it is fully seated (Fig. 4.3). 10. Connect power supply. 11. Sanitize the dispenser prior to use (see NSF-approved Cleaning and Sanitizing Procedure on page 11). 1 2 3

8 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Maintenance/Cleaning Mode –––––––––––––––––––––––––––––––––––––––––

Cleaning Mode (Dispensing Disabled) - Use when cleaning surface Entering Cleaning Mode disables the User Interface and allows you to clean the outside of the dispenser without accidentally dispensing water or ice. 1. To enter Cleaning Mode, press and immediately release the maintenance/clean switch (Fig. 5.1) so that only "FRESH FILTERED ICE AND WATER" displays in the user interface (Fig. 5.2). 2. To exit Cleaning Mode, press and immediately release the maintenance/clean switch so that the ice and water icons also display in the user interface. Maintenance Mode (All Operation Disabled) - Use when cleaning ice machine Entering Maintenance Mode disables all operations and allows you to safely clean and/or sanitize the ice machine and dispenser. 1. To enter Maintenance Mode, press and hold the maintenance/clean switch (Fig. 5.3) until displays in the user interface (Fig. 5.4). 2. To exit Maintenance Mode, press and hold the maintenance/clean switch until no longer displays in the user interface. Note: Entering and exiting Maintenance Mode will reset the six-month periodic maintenance reminder. Fig. 5 2 1 4 3

Accessing Internal Components ––––––––––––––––––––––––––––––––––––––

CAUTION! Except for routine cleaning and sanitizing, only qualified technicians should attempt to service or maintain this equipment. 1. Press and hold the maintenance/clean switch (Fig. 5.1) until displays in the user interface (Fig. 5.2). 2. Remove (unscrew) chrome ice dispenser chute (Fig. 6.1). 3. Remove the drip tray (Fig. 6.2). 4. Remove the two screws (Fig. 6.3) on the front panel (behind the drip tray). 5. Remove and set aside the front panel (Fig. 6.4) - do not disengage the plug on the back of the User Interface or the tubing at the water dispenser chute (if so equipped). Fig. 6 1 2 4 3

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 9 Filter Display Indicator Activation –––––––––––––––––––––––––––––––––––––

If you purchased your dispenser with a Follett filter, the filter display indicator activation has been preset at the factory. If you are using an “after market filter,” an adjustment may be made to activate the “Fresh Filtered Ice & Water” display. Activating “Fresh Filtered Ice & Water” 1. Remove the front panel as explained in Accessing Internal Components on page 9 then refer to Fig. 7. 2. Remove top panel (Fig. 7.1). 3. Remove (1) screw and top of control board enclosure (Fig. 7.2). 4. Locate the DIP switches on the dispenser's control board (Fig. 8). Use a fine-pointed object to move the “Filter” DIP switch (DIP switch #3) to the ON position. Deactivating the Six-Month Maintenance/Filter Change Reminder 1. Use a fine-pointed object to move the “PM” DIP switch (DIP switch #8) to the ON position. OFF ON Fig. 7 1 2 Fig. 8 Not used (OFF position) Ice only No internal filter Not used (OFF position) Not used (OFF position) 15 minute delay Not used (OFF position) Six-month PM enabled 1 Ice & water 2 Internal filter supplied or to display "Fresh Filtered" 3 4 5 30 minute delay 6 7 Six-month PM disabled 8

10 Undercounter Dispenser and Ice machine 7UC100A/7UD100A NSF-approved Cleaning and Sanitizing Procedure –––––––––––––––––––––––

Cleaning and sanitizing should be performed at least every 6 months (more often if local water conditions dictate). For initial startup, only sanitizing is required. IMPORTANT!Prior to cleaning and sanitizing, the dispenser must be moved forward at least 4" (10.16 cm). Do not remove the Bin Lid, cleaning and sanitizing solution is added through the Bin Lid Access Spout (Fig. 9.6). WARNING! ▪ Place the dispenser in Maintenance Mode prior to servicing or cleaning the ice machine. See Maintenance/Cleaning Mode on page 9. ▪ For protection, rubber gloves and safety goggles (and/or face shield) should be worn when handling SafeCLEAN Plus™. ▪ Do not use bleach, it will damage the dispenser. Required Supplies ▪ 7 Series: 24 oz. (0.71 L) of SafeCLEAN Plus liquid 15 Series: 48 oz. (1.42 L) of SafeCLEAN Plus liquid ▪ Funnel and Bucket Ice machine and Dispenser 1. Dispense all the ice out of the unit. 2. Press and hold maintenance/clean switch until displays in the user interface to enter Maintenance Mode. 3. Remove (unscrew) chrome ice dispense chute (Fig. 9.1). 4. Remove drip tray (Fig. 9.2). 5. Remove (2) screws located behind the drip tray (Fig. 9.3). 6. Move front panel and place on top or beside unit (Fig. 9.4). 7. Remove plug cap from the end of drain tube (Fig. 9.5) and lower tube to drain water into bucket. After the system has been drained of water replace plug cap in drain tube. 8. Secure tube in holder. 9. Remove cap from bin lid cover (Fig. 9.6). 10. Screw bin lid cover cap onto ice discharge chute (Fig. 9.7). Fig. 9 1 2 4 6 7 5 3

11. 7 Series: Mix 24 oz. (0.71 L) of SafeCLEAN Plus liquid with three gallons (11.4 L) of water. 15 Series: Mix 48 oz. (1.42 L) of SafeCLEAN Plus liquid with six gallons (22.7 L) of water. 12. Pour SafeCLEAN Plus solution into bin lid access spout until solution reaches the spout neck. 13. Allow the SafeCLEAN Plus solution to remain in unit for 15 minutes. 14. While machine is cleaning, remove top and right side panel to access and clean air-cooled condenser. 15. Submerge ice dispense chute in the remainder of SafeCLEAN Plus solution for 2 minutes. Rinse with clean, potable water. 16. Drain system by lowering drain tube into bucket. 17. Secure drain tube into holder. 18. Fill and drain twice with potable water. Secure drain tube. 19. Place a bucket under the dispense chute and remove cap. Note: Some SafeCLEAN Plus solution will remain and drain out when cap is removed. Reposition cap on bin lid spout. 20. Reinstall front panel, ice dispense chute, and drip tray. 21. Press and hold maintenance/clean switch to exit Maintenance Mode. Undercounter Dispenser and Ice machine 7UC100A/7UD100A 11 NSF-approved Cleaning and Sanitizing Procedure (continued) –––––––––––––––– User Interface and Exterior Cabinet 1. Press and release maintenance/clean switch so that only "FRESH FILTERED ICE AND WATER" displays in the user interface to enter Cleaning Mode (and disable dispensing). 2. Plastic parts, including the user interface, can be cleaned with a non-abrasive glass cleaner. Clean stainless steel panels with stainless steel cleaner. 3. Press and release maintenance/clean switch to put unit back into service. Service ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– LED Indicator Description The LED Indicator is located behind the front panel. Fig. 10 e y l

n a e lC M P y a r t pi r D k a e l r e ta W s s e r p IH s p m a IH e c i v r e S t n ia M r e ta w w o L a le d e m iT c y c p e e lS e c i g n ik a M n i b w o L N O r e w o P

LED Name LED Color Description Clean Green The dispenser is in Cleaning Mode. Dispenser is disabled to allow for cleaning of front panel. See Maintenance/Cleaning Mode on page 9. — N/A Not used. PM Red Six-month periodic maintenance required. Drip tray Red Drip tray full. Water leak Red Internal leak in dispenser. High amps Red Auger gearmotor has exceeded 0.55A. The HI amps and Time delay LEDs will illuminate, the machine will shut down for one hour, the LEDs will turn off, and the machine will resume normal operation. Service Red 8000 hour bushing check (call Follett technical service group at (877) 612-5086 or +1 (610) 252-7301). Maintenance Yellow Enter Maintenance Mode by pressing and holding maintenance/clean switch for 5 seconds. Unit will not make or dispense ice. Low water Yellow Insufficient water supply to machine or no low bin LED upon startup. Time delay Yellow Ice production will not resume for at least 15 minutes after a full bin is achieved and a minimum amount of dispense activity has elapsed. Sleep cycle Green After a full bin and 10 minutes of non-use, the unit goes into standby and will not produce ice until either 12 hours has elapsed or ice or water has dispensed. Making ice Green Gearmotor, compressor, and fan motor energized. Low bin Green Bin switch closed calling for ice. Power on Green Power supplied to unit. 12 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) ––––––––––––––––––––––––––––––––––––––––––––––––––––

Evaporator Disassembly 1. Disconnect power from the dispenser. 2. Turn off water supply to dispenser. 3. Remove (unscrew) chrome ice dispenser chute (Fig. 11.1). 4. Remove the drip tray (Fig. 11.2). 5. Remove the two screws (Fig. 11.3) on the front panel (behind the drip tray). 6. Remove and set aside the front panel (Fig. 11.4) - do not disengage the plug on the back of the User Interface. 7. Lift and remove the top panel, set aside (Fig. 16.5). 8. Remove two screws (Fig. 11.6) and remove left side panel. 9. Remove two screws (Fig. 11.7) and remove right side panel. Fig. 11 2 4 2 1 1 3

6 5 7 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 13 Service (continued) ––––––––––––––––––––––––––––––––––––––––––––––––––––

10. Unplug the gear motor (three connectors) (Fig. 12). 11. Remove ground screw connection. 12. Remove gear motor: ▪ Remove M6 allen screw, retainer, spacer and key (Fig. 13.1). ▪ Remove two M6x90 allen screws (Fig. 13.2). ▪ Pull gear motor from auger (Fig. 13.3). ▪ Remove main housing insulation (Fig. 13.4). 13. Remove all traces of petro-gel from auger shaft. 14. Remove compression nozzle: ▪ Loosen hose clamp (Fig. 14.1). ▪ Remove transport tube (Fig. 14.2). Fig. 12 Fig. 13 4 2 3 1 2 Fig. 14 1

2 14 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––

15. Remove M6 socket head allen screw (Fig. 15.1). 16. Remove compression nozzle retainer (Fig. 15.2). 17. Remove compression nozzle (Fig. 15.3). 18. Remove main housing: ▪ Disconnect vent line from T fitting (Fig. 16.1). 19. Remove three M6x25 socket head allen screws (Fig. 17.1). 20. Remove main housing (Fig. 17.2). Fig. 15 1 2 3 Fig. 16 1 Fig. 17 2 1

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 15 Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––

21. Remove and discard mating ring and seal (Fig. 18.1). 22. Carefully remove auger (Fig. 18.2). WARNING! Use caution when removing auger. The auger is very sharp - handle with care to avoid personal injury. Evaporator Assembly 1. Remove and inspect main housing O-ring seal. Replace if damaged in any way. 2. Clean O-ring groove. Lubricate O-ring with Petro-gel and reinstall. 3. Use cardboard disc to press new mating ring into main housing (Fig. 19.1). 4. Lube the shaft with liquid soap in the area shown (Fig. 19.2) and slip on seal and spring (Fig. 19.3). Note: Do not touch the sealing surfaces with bare hands. Contact with bare skin will cause premature seal failure. Fig. 18 12 Fig. 19 1 Cardboard disc Do NOT touch! 5. Install auger (Fig. 19.4). 6. Install main housing: ▪ Slide main housing onto auger shaft (Fig. 20.1). ▪ Install three M6x25 allen screws (Fig. 20.1). ▪ Connect vent line to T fitting (Fig. 20.1). 2 4 3 Fig. 20 3 1 2

16 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––

7. Install compression nozzle: ▪ Remove and inspect compression nozzle O-ring seal. Replace if damaged in any way. ▪ Clean O-ring groove. Lubricate O-ring with Petro-gel and reinstall. ▪ Install compression nozzle (Fig. 21.1). ▪ Install compression nozzle retainer (Fig. 21.2). ▪ Install M6 socket head allen screw (Fig. 21.3). 8. Install transport tube (Fig. 22.1). 9. Tighten hose clamp (Fig. 22.2). Fig. 21 Fig. 22 2 3 2 1

1 10. Install gear motor: ▪ Install main housing insulation (Fig. 23.1). ▪ Slide gear motor onto auger shaft (Fig. 23.2). ▪ Install two M6x90 allen screws (Fig. 23.3). Fig. 23 1

3 3 2

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 17 Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––

11. Use screwdriver to orient auger shaft to align with motor shaft keyway (Fig. 24.1). 12. Install key into keyway (Fig. 24.2). 13. Install spacer, ensure that key is captured in slot (Fig. 25.1) 14. Insert screwdriver into groove of auger shaft and pry shaft outwards (Fig. 26.1). 15. Insert retainer into groove (Fig. 26.2), ensure that retainer is aligned with hole in spacer. Fig. 24 2 1 Fig. 25 1 Fig. 26 1 2

18 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) ––––––––––––––––––––––––––––––––––––––––––––––––––– 16. Install screw and tighten (Fig. 27.1). Fig. 27 1 2

17. Plug in gear motor (Fig. 28). ▪ BLUE to BLUE ▪ BLACK to BLACK ▪ WHITE to WHITE ▪ Connect ground wire with ground screw. Fig. 28 BLUE to BLUE BLACK to BLACK WHITE to WHITE

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 19 Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– Water Feed Schematic Evaporator Float Water Chute (optional) Water Solenoid Valve (optional) Filter (optional) Water Solenoid Valve 20 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– Bin Melt Water/Evaporator Feed/Clean Out System Schematic Storage Bin Vent System Schematic Storage Bin Vent Tube Reservoir Undercounter Dispenser and Ice machine 7UC100A/7UD100A 21 Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– Refrigeration Schematic 22 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– Condenser Fan Motor Removal Undercounter Dispenser and Ice machine 7UC100A/7UD100A 23 Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– User Interface Display Identification Operation Display Condition Procedure

Normal operation Cleaning Mode — Press and release maintenance/clean switch to clean the user interface without dispensing ice or water (see Maintenance/Cleaning Mode on page 9).

Drip tray full Empty drip tray.

PMSix-month periodic maintenance required Maintenance Mode Service - 8000 hr bushing check Follow Maintenance Mode procedure (below) and also see NSF-approved Cleaning and Sanitizing Procedure on page 11. Enter Maintenance Mode by pressing maintenance/clean switch until displays. Complete the cleaning and sanitizing procedure shown on page 11 and change the filter, if so equipped. Exit Maintenance Mode by pressing and holding maintenance/clean switch until no longer displays. Call Follett Technical Service Group at (877) 612-5086 or +1 (610) 252-7301. The flashing wrench indicates that the 8000 hr bushing check is required.

High amps Contact Follett technical service group at (877) 612-5086 or +1 (610) 252-7301. Note: For dispensers after serial number D45191, the phone and wrench will not be illuminated.

Internal leak in dispenser Locate leak and repair - Press reset on control board. Contact Follett if ice machine is leaking.

Sleep mode Press either dispense button to return to normal operation. 24 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Service (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––– Electrical Wiring Diagram E C A F R E T N I R E S U E C N A N E N T A N I E A L

R E W OP S I S SA HC R OS N E S R E TA W Y A R T PI RD R OS N E S R E TA W NI B M R I OV RE SE R C R OS N E S R E TA W

Undercounter Dispenser and Ice machine 7UC100A/7UD100A 25 Parts ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Exterior 6 4 7 11 5 10 9 2 3

8 1

26 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Exterior Reference # Description Part # 1 Drain, Tray Assy 00957613 2 Panel, Front Assy - Includes Water Nozzle and Plug 00957621 3 Chute, Water (water option) 00957688 4 Panel, Top Left 00947010 5 Panel, Top Right 00947028 6 Panel, Top 00957654 7 Panel, Rear 00957662 8 Panel, Lower, 7UC100A Height: 12.0" (304.8 mm) 00932855 Panel, Lower, 7UD100A Height: 10.0" (254 mm) 00932863 9 Panel, Intake 00947119 Not Shown Cord, 115 VAC 00958058 Not Shown Packaging for Returns, Dispenser 00957993 Not Shown Covers, Agion, User Interface 00969030 10 Panel, Bottom Left/Right, 7UC100A 00967331 Panel, Bottom Left/Right, 7UD100A 00967356 11 Panel, Bottom Rear, 7UC100A 00967349 Panel, Bottom Rear, 7UC100A 00967364 Not Shown Fitting, Elbow - 1/4" FPT x 1/4" Tube 00974261 Not Shown Fitting, Elbow - 1/4" FPT x 3/8" Tube 00990796 Not Shown Drip Tray Drain Kit 00956375 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 27 Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Interior 7 4 3 1 12 2 10 10

9 8 6 5 11 14 13 12

28 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Interior Reference # Description Part # 1 Valve, Dispense Solenoid (water option) 00957704 2 Switch, Cleaning 00957712 3 Drain/Feed Tube with Cap 00957720 4 Valve, Failsafe Solenoid 00957738 5 Compressor with Mounting Hardware 01157296 6 Condenser 00958017 7 Condenser Fan, Cord and Hardware 01157288 8 Control Board with Stand-offs 00958033 9 Capacitor, Gearmotor 00958041 10 Sensor, Retainer Hardware Kit 00958066 11 Relay and Overload 00157387 12 Refrigeration, Cap Tube and Drier 01157379 13 Roller Kit, Set of 4 00924753 14 Bracket, Stop 00961292 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 29 Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Bin Assembly 9 3 4 5 6 2 1 7 8 30 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Bin Assembly Reference # Description Part # 1 Ice Chute Assembly 00957670 2 Ice Transport Tubing with Insulation 00957746 3 Switch, Shuttle 00957753 4 Shuttle, Complete Assy 00957761 5 Lid, Bin Assy 00957779 6 Bin, Assy 00957787 7 Auger, Dispense 00957795 8 Motor, Dispense 00957803 9 Cap and Insulation, Bin 00957936 Not Shown For serial numbers D17619 and below: Bin Cap 00931519 Ice Chute 00927210 Chute Adapter 00926550 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 31 Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Evaporator Assembly 1011 12 13 14 13 2 8 5 6 3 1 7 4 9 32 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Parts (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––– Evaporator Assembly Reference # Description Part # 1 Gearmotor Assembly 00957811 2 Main Housing with Front Seal and Screws 00957829 3 Screws, Main Housing 00957837 4 Auger with front seal (includes gearmotor hardware kit) 00957845 5 Ice Compression Nozzle Assy 00957852 6 Front Seal and O-Ring 00957860 7 Evaporator Assembly with Insulation 01157353 8 Housing, Bushing with Insulation 00957886 9 Hardware kit, Gearmotor (For serial numbers E01087 and above) 01048628 9 Hardware kit, Gearmotor (For serial numbers below E01087) 00957894 10 Reservoir and Float Complete Assy 00957902 11 Lid, Reservoir with Insulation and O-Ring 00957910 12 Float Valve 00957928 13 “T” Fitting - 1/4" 502923 14 Tubing - 1/4" 502079 Miscellaneous Reference # Description Part # Not Shown Water filter cartridge, 5 micron 00968107 Not Shown Cleaning and sanitizing kit, single use 00979856 Not Shown SafeClean Plus liquid, case of 6 01149954 Not Shown SafeClean Plus liquid, case of 24 01149962 Not Shown IMS II sanitizer concentrate, 16 oz 00979674 Undercounter Dispenser and Ice machine 7UC100A/7UD100A 33 34 Undercounter Dispenser and Ice machine 7UC100A/7UD100A Undercounter Dispenser and Ice machine 7UC100A/7UD100A 35

SafeCLEAN is a trademark of Follett LLC. Follett is a registered trademark of Follett LLC, registered in US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 follettice.com 00966879R09 © Follet LLC 12/16


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply