FLAMMA FA05 (01) PDF MANUAL

FLAMMA FA05 (01) PDF SUMMARY:

What should I do for power supply?

Please connect the designated adapter to an AC outlet of the correct voltage. Please be sure the adapter supplies DC 9v 1.5A ,center negative . Unplug the adapter when not in use or during electrical storms. Use only the original power supply.

---

What are the device’s FCC Rules?

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired operation

---

Where is the guitar input?

The guitar input is on the top panel.

---

What does the GAIN knob do?

Adjusts gain level of amp model.

---

What does the TONE knob do?

Adjusts tone color of amp model.

---

What does the VOL knob do?

Adjusts volume level of amp model.

---

What does the AMP knob do?

Rotate to select from 7 preamp models.

---

What does the CHR/TREM knob do?

Adjusts level of chorus and tremolo effect.

---

What does the DLY/REV knob do?

Adjusts level of delay and reverb effect.

---

What does the LED screen display?

Displays current drum machine and tuner settings.

---

What does the DRUM knob do?

Press/rotate to edit settings of drum machine and utilize tuner.

---

What does the SETTING LED button do?

Turn drum machine on/off. Press hold to enter hidden parameters.

---

Where do I connect to power supply?

Connect to the DC IN on the back panel.

---

Where is the power switch?

The power switch is on the back panel.

---

Where is the Bluetooth switch?

The Bluetooth switch is on the back panel.

---

Where do I plug in external media device for audio playback?

Use the 1/8" stereo jack AUX IN on the back panel.

---

Where is the headphone output?

The 1/8" stereo Headphone output is on the back panel.

---

Where is the battery compartment?

The battery compartment is on the back panel.

---

How do I start the device?

Plug in power supply or place AA battery into the battery compartment. Switch POWER to ON position. The LED screen will light up.

---

How do I select amp model?

Rotate the knob to select from 7 different amp models. You can adjust the gain level, tone, and volume level of amp by rotating the GAIN/TONE/VOL knobs.

---

How do I select effects?

Rotate the CHR/TREM knob to select and adjust levels between chorus and tremolo effects. Rotate DLY/REV knob to select between and adjust levels of delay and reverb effects. In CHR/TREM, the left side value is for adjusting the level of the chorus effect while the right side is for adjusting tremolo effect level. In DLY/REV, the left side is for adjusting level of delay effect and the right is for amount of reverb effect.

---

How do I save Settings?

The GAIN/TONE/VOL of amp and parameters of effects will be stored automatically in current amp slot, even after you switch to the other amp slots.

---

What are the preamp types?

clean1, clean2, od1, od2, crunch, Lead, Rhythm

---

How do I use the tuner?

Press and hold the DRUM knob to access the TUNER. Press DRUM or SETTING button to exit. In the tuner mode, there are two parts in display screen: a left block and a right block.

• Left block: It will show up the name of note. Dot between two blocks indicates the semitone.
• Right block: It will indicate the note you play is whether lower or higher than the displayed note on the left. When the note you play is lower than displayed note, the right block display will move anticlockwise. When the note you play is higher than displayed note, the right block display will move clockwise. When the note you play match the displayed note, all the display of right block will light up.

---

How do I edit hidden parameter?

Press and hold the SETTING button to access hidden parameters editing mode. SETTING LED will turn red and blink. There are six hidden parameters to edit:

1. NG: Rotate GAIN to adjust the noise gate level
2. CHR RATE: While chorus effect is activated, rotate the CHR/TREM to adjust the rate of chorus effect
3. TREM RATE: When the tremolo effect is activated, rotate the CHR/TREM to adjust the rate of the effect
4. DLY TIME: When the delay effect is activated, rotate the DLY/REV to adjust the timing of the delay effect
5. REV DECAY: When the reverb effect is activated, rotate the DLY/REV to adjust the decay.
6. DRUM SPEED: Rotate DRUM knob to adjust the speed of drum machine. The LED screen will show the speed as 0-99 (Notice: 0-99 is not BPM but the relative speed of the drum machine.) Press DRUM/SETTING or rotate AMP knob to quit hidden parameter editing menu. The parameter settings will be stored automatically

---

How do I use the drum machine?

• Switch on/off: Press SETTING button to switch drum machine on/off. The LED button will stay red
• Select rhythm type: Rotate DRUM knob to select from 40 different rhythms. The LED screen will indicate the number of current rhythm.
• Volume Level: Press DRUM to access Drum Machine volume level menu. Rotate DRUM to adjust volume level from 0-9 as displayed on the LED screen