EVERFOCUS EDH5210W (01) PDF DOCUMENT

1. **Do not install the camera near electric or magnetic fields.** Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere with camera operation.

2. **Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein.** Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.

3. **Try to avoid facing the camera toward the sun.** In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination beyond the capability of the camera to compensate.

4. **Keep the power cord away from water and other liquids and never touch the power cord with wet hands.** Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric shock.

5. **Never install the camera in areas exposed to oil, gas or solvents.** Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.

Do not operate the camera beyond the specified temperature, humidity or power source ratings. This camera is suitable for indoor operation. Use the camera at temperatures within -10°C~50°C (14°F~122°F) and in an indoor environment; this device is not rated as weather proof. The input power source is 12VDC. The use of properly fused or Class 2 power limited type supplies are highly recommended.

Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind, snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional support for the camera.

• HDcctv 2.1 Megapixel real time 1920×1080/1280×720 HD video over coax for superlative image detail

• Supports video outputs of 1080p30/25 and 720p60/50 (field select)

• Varifocal 3.6~16mm megapixel lens

• Choice of Day/Night operation or Full Color Images in Low Light

• Provides 3-D DNR to improve picture clarity while enabling DVRs to improve disk storage utilization

• 3-Axis Gimbal for Flexible mounting and positioning

• Easy to use OSD setup menu with an array of options

• Enhanced low light sensitivity increase of up to 8x

• Lens Shading Compensation to offset diminished light transmission through lens periphery for uniform image illumination

• Electronic WDR and HSBLC [Highlight Suppression Back Light Compensation] to handle lighting imbalance and bright areas in the scene

• Digital zoom increases effective lens magnification up to 20X

• Up to 24 Privacy Zones

• Dead pixel compensation for increased clarity and extended service life

• SD TV Out for aim and focus using a standard hand held test monitor

The original box should contain the following items:

• Camera

• Manual

• Pigtail Cable (Power)

• Mounting Template

• Screws

• Service Video Cable

If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The shipping carton is the safest container in which the unit may be transported. Save it for possible future use.

Pickup Device	1/2.8″ Sony 2.43 Megapixel Color Progressive CMOS sensor
Image Pixels	1920(H)x1080(V) with 2.8μx 2.8μ pixel size
HDcctv Image Area Dimensions	5.38mm (H) x 3.02 mm(W); ø 6.17 mm area diagonal
Sensitivity	0.1lux/F=1.2 (Sens-Up OFF)
S/N Ratio	More than 50dB
Video Format Main Output	HDcctv
Video Resolution/Mode Main Output	Field select 1080p30/25, 720p60/50
Main Output Connector	BNC-F
Video Format Test Output	NTSC/PAL selectable
Test Output Connector	Pin connector on board; adapter cable to BNC-F supplied
Lens Type	3.6~16mm Megapixel DC Iris Lens
FOV Angle	72°~19° Horizontal
Shutter Speed	Auto/Manual selectable
OSD	Yes (5-axis joystick control)
D/N Mode	Auto, Color, B/W (Electronic D/N)
Exposure Control	Automatic Electronic Shutter
Digital WDR	Weight Level Adjustable 0~4
DSS	Low light boost up to 8X
Lens Shading Compensation	On / Off
HSBLC (Highlight Suppression Back Light Compensation)	Off/On
Auto Gain Control	Variable relative level 0~10
White Balance	ATW / Push / Manual
DNR – 3D	Low / Medium / High
Digital Zoom	1X~20X
Image Flip	Off /V Flip/H flip/H+V flip (rotate)
Programmable Privacy Zones	24 areas independently adjustable for size, location, color
Language	English
Dead Pixel Compensation	Manual Off/On
Power Source & Consumption	DC12V (+/-10%) @ 220mA
Mounting/Positioning	3-Axis gimbal
Dimensions	Body: 95.3mm / 3.75″ (Max. H) x Ø136.4mm / Ø5.37″ Base Diameter (W)
Weight	343g / 12.1oz
Housing Color	Choice of black or white
Operating Temperature	14°F to 122°F
Operating Humidity	20%~80% humidity, non-condensing

The dimensions are as follows (in inches):

• Top Diameter: Ø 3.94″

• Base Diameter: Ø 5.31″

• Mounting Hole Diameter: Ø 4.27″

• Height (Dome to Base): 1.77″

• Total Height: 3.81″

The main components accessible after removing the dome cover are:

• Far/Near Adjustment Knob

• Tele/Wide Adjustment Knob

• OSD Menu Switch

• Service Video Connector

The OSD Menu Switch is a 5-axis joystick with the following functions:

• **UP, DOWN:** Menu up / down

• **LEFT, RIGHT:** Change Values

• **MENU (press inwards):** MENU (SELECTION KEY) / Enter

The main installation parts are as follows:

1. Mounting Template

2. Base

3. Pan Adjust

4. Tilt Adjust

5. Rotate Adjust

6. Cover

7. Housing Cover

8. Dome Cover

The EVERFOCUS EDH5210W camera has two main connections:

• **DC12V In (Black):** Connect this to a DC12V Adapter for power.

• **BNC Female (HDcctv Jack):** Connect this to an HDcctv DVR or other HDcctv Signal Equipment for video output.

Additionally, there is a **Service Video Connector** inside the camera housing. You can use the provided Test Cable to connect this to a handheld monitor (NTSC Video In) for easy setup and focusing during installation.

When installing the camera, make sure that all cable ends and connectors are protected from humidity and other outdoor environments.

The main OSD menu contains SETUP, EXPOSURE, WHITE BALANCE, WDR/BLC, DNR, DAY & NIGHT, IMAGE, SPECIAL, SYSTEM, Reset Date All, and EXIT. The detailed structure is below:

Main	Sub Menu	Sub Menu / Options	Values / Further Options
EXPOSURE	BRIGHTNESS	0 ~ 20
	AE MODE	NORMAL AE / INDOOR
	LENS(IRIS)	MANUAL / AUTO
	SHUTTER	MANUAL / AUTO	LEVEL	1/30(25), 1/60(50), 1/120(100), 1/240, 1/500, 1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.
			RETURN	BACK / EXIT
	DSS	OFF, X2, X3, X4, X5, X6, X7, X8
	AGC	0 ~ 10
	BASE FREQ	60Hz / 50Hz
	RESET DATA	BACK / DEF.
	RETURN	BACK / EXIT.
WHITE BALANCE	WB MODE	AUTO / AUTOext / PUSH / MANUAL	COLORTEMP. – LOW / MIDDLE / HIGH
			R-GAIN – 0 ~ 20
			B-GAIN – 0 ~ 20
			RETURN – BACK / EXIT
	SATURATION	0 ~ 20
DWDR / BLC	MODE	OFF, BLC, DWDR
	WDR WGT	0 ~ 4
	BLC OSD	OFF ~ ON
	BLC POS-X	0 ~ 20
	BLC POS-Y	0 ~ 20
	BLC SIZE-X	0 ~ 20
	BLC SIZE-Y	0 ~ 20
	RESET DATA	BACK / DEF.
	RETURN	BACK / EXIT.
	DNR	OFF, LOW, MIDDLE, HIGH
DAY & NIGHT	COLOR/B&W/ AUTO	D&N DETECT	AGC / SENSE
		DELAY	1sec, 3, 5, 10, 15, 20, 25, 30, 40, 50, 60sec
		D->N LEVEL	0 ~ 20(AGC) / 0 ~ 10(SENSE)
		N->D LEVEL	0 ~ 20(AGC) / 0 ~ 10(SENSE)
		RESET DATA	BACK / DEF.
		RETURN	BACK / EXIT.
IMAGE	SHARPNESS	0 ~ 10
	FLIP	OFF, H FLIP, V FLIP, HV FLIP
	LENS SHADING	OFF, ON
	DZOOM	1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x
	RESET DATA	BACK / DEF.
	RETURN	BACK / EXIT.
SPECIAL	PRIVACY (OFF/ON)	ZONE NO.	0 ~ 23
		ZONE OP.	OFF / ON
		X-POS	0 ~ 60
		Y-POS	0 ~ 40
		X-SIZ	0 ~ 40
		Y-SIZ	0 ~ 40
		COLOR	BLK, WHI, YEL, CYN, GRN, MAG, RED, BLU
		TRANS.	0 ~ 4
		RESET DATA	BACK / DEF.
		RETURN	BACK / EXIT.
	HLMASK (OFF/ON)	LEVEL	0 ~ 20
		COLOR	BLK, WHI, YEL, CYN, GRN, MAG, RED, BLU
		RESET DATA	BACK / DEF.
		RETURN	BACK / EXIT.
		PATTERN	OFF, 1, 2
	DISPLAY INFO.	CAMERA ID.	OFF / ON
		MOTION CHECK	OFF / ON
		RETURN	BACK / EXIT.
	RESET DATA	BACK / DEF.
	RETURN	BACK / EXIT.
SYSTEM	SDI FORMAT	1080p / 720p
	SDI FPS	30 / 25 (when 1080p), 60 / 50 (when 720p)
	CVBS FORMAT	NTSC / PAL
	APPLY	OK
	SYSTEM INFO	S/W VERSION
		SET VERSION
	RESET DATA	BACK / DEF.
	RETURN	BACK / EXIT.