ERGOAV ERMSL1-01B (01) PDF Document

Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns, please contact Technical Support.

DANGER: Please carefully read all instructions before attempting installation.

CAUTION: Use with products heavier than the maximum weights indicated may result in instability causing possible injury.

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

• This product is designed for use in wood stud, and solid concrete walls. – DO NOT install into drywall alone.

• The wall must be capable of supporting four times the weight of the TV and mount combined.

• Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

• Do not use outdoors.

• Route cords and cables properly to avoid mechanical damage.

• SAVE THESE INSTRUCTIONS.

Weight Restrictions:

The maximum weight capacity is 99 lbs / 44 kg. Do not use this product if your TV weighs more. Using the mount with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing damage and/or injury.

VESA Pattern Requirements:

• Minimum VESA Pattern: 200mm x 100mm (8″ x 4″) (W x H)

• Maximum VESA Pattern: 600mm x 400mm (24″ x 16″) (W x H)

Supported VESA patterns include:

• 100 mm ≈ 4″

• 200 mm ≈ 7 7/8″

• 300 mm ≈ 11 3/4″

• 400 mm ≈ 15 3/4″

• 600 mm ≈ 23 3/5″

If your TV’s VESA Pattern is smaller than 200mm x 100mm or greater than 600mm x 400mm, this mount is NOT COMPATIBLE with your TV.

The following tools are needed for installation but are not included:

• Stud Finder

• Awl

• Tape Measure

• Electric drill

• Pencil

• Level

• Phillips Screwdriver

• 7/32″ (5.5mm) Wood Drill Bit

• 3/8″ (10mm) Socket Wrench

• 1/2″ (13mm) Socket Wrench

The following are needed for concrete installations only:

• 3/8″ (10mm) Concrete Drill Bit

• Hammer

Before installation, you must verify your wall type. The ERGOAV ERMSL1-01B is designed for use in:

• Wood Studs (with Drywall)

• Solid Concrete Wall

CAUTION: DO NOT install into drywall alone. If you are not sure of the wall construction, contact Technical Support.

Step 1: Secure the TV Brackets to the TV

1. Select TV Bolts: Only one size bolt will fit your TV (M4, M6, or M8). Test the bolts to find the correct size.

2. Verify Bolt Length: Ensure adequate thread engagement with bolts or a bolt/spacer combination. We recommend thread engagement by at least 5 turns.

• Too short will not hold the TV.

• Too long will damage the TV.

3. Position Brackets: When attaching the TV brackets [01] to the back of the TV, ensure the ends with the rounded holes are pointing towards the top of the TV and are equally centered on the back of the TV. The bolt hole locations on your TV may vary.

4. Consider TV Back Shape:

• Option A (For Flat Back TV): Attach the brackets [01] using the correct bolts (C1/D1/E1) and washers (B1/B2). Use spacers (F1/F2) if needed.

• Option B (For Curved Back TV): Spacers must be tall enough so the curve on the back of the TV does not interfere with the mounting plate. Use appropriate longer bolts (C2/D2/E2/E3), washers (B1/B2), and spacers (F1/F2/F3).

• Option C (For TV with a “Bump”): Spacers must be tall enough so TV brackets are flush (NO GAP) on the bump. Use appropriate longer bolts, washers, and spacers.

• Option D (For TV with Cable Interference): Use spacers to create extra space between the TV and TV brackets for cables.

• Option E (For Recessed Holes): Spacers need to fill in the recessed holes on the back of the TV so that the TV brackets are as close to the TV as possible.

NOTE: Please do not over-tighten the TV bolts to avoid damaging your TV.

WARNING: To avoid potential personal injury or property damage, Do Not over-tighten the Lag Screws [A1]! Tighten them only until they are pulled firmly against the Wall Plate. Do Not use a drill when tightening the Lag Screws [A1]; only use a socket wrench. DO NOT USE THE ANCHOR [A2] FOR THIS STEP. Ensure the Arm Assembly is securely fastened before proceeding. Nominal wood stud size is 2” x 4” (51mm x 102mm).

Step 2A-1: Locate Studs

Use a stud finder to locate wood studs or an awl to verify the edges. Mark the edge and center locations. For corner mounts, find your stud locations, mark them, and then lay the mount out on the floor to configure it to your stud locations before installing. The installable range is a minimum of 12″ and a maximum of 27″ between studs.

Step 2A-2: Mark Pilot Holes

Position the Wall Plate Template [03] at your desired height and line up the holes with your stud center line. Level the Wall Plate Template [03] and mark the location for the pilot holes.

Step 2A-3: Drill Pilot Holes

Drill the 6 pilot holes using a 7/32″ (5.5mm) diameter drill bit. Make sure the depth of the pilot holes is at least 2 3/4″ (70mm) deep.

Step 2A-4: Install Arm Assembly

HEAVY! You may need assistance with this step. Install the Arm Assembly / Wall Plate [02] using 6 Lag Screws [A1]. Tighten the Lag Screws [A1] only until they are pulled firmly against the Wall Plate and the wall using a 1/2″ (13mm) socket wrench. Do not use a drill to tighten.

WARNING: To avoid potential personal injury or property damage, Do Not over-tighten the Lag Screws [A1]! Tighten them only until they are pulled firmly against the Wall Plate. Do not use a drill to tighten them; only use a socket wrench. Ensure the Arm Assembly is securely fastened before proceeding. Mount directly onto the concrete surface without any covering. The thickness of the concrete wall must exceed 5 1/2″ (140mm).

Step 2B-1: Mark Pilot Holes

Position the Wall Plate Template [03] at your desired height. Level the template and mark the locations for the pilot holes. For corner mounts, the distance between the center location and the corner of the wall should be approximately 27″ (700mm).

Step 2B-2: Drill Pilot Holes

Drill the 6 pilot holes using a 3/8″ (10mm) diameter concrete drill bit. Make sure the depth is at least 3″ (75mm) deep.

Step 2B-3: Insert Anchors

Use a hammer to knock the Wall Anchors [A2] into the wall. Be sure the anchors are seated flush with the concrete surface.

Step 2B-4: Install Arm Assembly

HEAVY! You may need assistance with this step. Install the Arm Assembly / Wall Plate [02] using 6 Lag Screws [A1]. Tighten the Lag Screws [A1] only until they are pulled firmly against the Wall Plate and the wall using a 1/2″ (13mm) socket wrench.

HEAVY! You may need assistance with these steps.

Step 3-1: Prepare the Brackets

Remove the Pre-Assembled Bolts [S2] from the Locking Tabs on the TV Brackets [01] using a Phillips screwdriver. Save these bolts for use in Step 3-3.

Step 3-2: Hang the TV

Before attempting to hang the TV, make sure the Locking Tabs are positioned towards the bottom of the TV. Hang the TV with the TV Brackets [01] onto the Front Support. Make sure that the upper and lower hooks on the TV Brackets are over the Front Support Bars.

Step 3-3: Secure the TV

Position the Locking Tabs towards the top of the TV and secure the Locking Tabs in place using the Bolts [S2] from Step 3-1. Firmly tighten the bolts [S2] with a Phillips screwdriver.

Tilt Adjustment

1. Slightly loosen the two tilting Nuts [T] using a 3/8″ (10mm) socket wrench.

2. Adjust the TV to your desired tilt angle.

3. Retighten the two tilting Nuts [T] using the socket wrench to secure the TV in place.

Level Adjustment

If needed, the TV can be leveled.

1. Slightly loosen the two Bolts [S1] on the rear of the Front Support with a Phillips screwdriver.

2. Level your TV.

3. Retighten both Bolts [S1] to hold the TV in place.

Swivel Adjustment

The mount can be swiveled to the left, right, or positioned in the middle. Gently push or pull the TV to adjust its position.