ELECTRO-VOICE EVID-S5.2XB (01) PDF Document

For a 100 Watt system, use 18 AWG for up to 230 ft, 16 AWG for 360 ft, 14 AWG for 560 ft, and 12 AWG for 910 ft. For a 40 Watt system, use 18 AWG for 560 ft, 16 AWG for 900 ft, 14 AWG for 1400 ft, and 12 AWG for 2300 ft. For a 10 Watt system, use 18 AWG for 2300 ft, 16 AWG for 3600 ft, 14 AWG for 5600 ft, and 12 AWG for 9100 ft.

First, draw a level line on the mounting surface. Second, align the screw holes of the U-Bracket on that line. Third, install two mounting screws to securely attach the U-Bracket to the wall.

Once the U-Bracket is installed, insert the two provided screws into the U-Bracket mounting points. Loosely tighten these screws using the provided Allen wrench. Aim the speaker in the desired direction, then fully tighten the two screws to secure the speaker to the U-Bracket.

Loosen both gland nuts and push the wires through them. Connect the wires to the Euroblock connector. Plug the connector into the speaker. Insert the four screws into the weather cover and loosely tighten them. Tighten the four screws to secure the cover, adjust the wire length, and finally tighten the gland nuts.

Loosen both gland nuts. Push the wire through one of the gland nuts and insert the provided plug into the other. Tighten the gland nut with the plug to seal it. Connect the wire to the Euroblock connector, plug it into the speaker, secure the weather cover with four screws, adjust wire length, and tighten the remaining gland nut.

Use the rotary switch on the input panel to select the desired power tap. If you wish to set the speaker to 8 ohm mode, you must also remove the safety screw from the panel.

Remove the existing logo. Clean the surface thoroughly with alcohol. Align the new logo with the recess on the grille. Remove the paper backing from the logo and insert it into the recess. Press firmly to ensure it is applied correctly.

Check that all electronics are powered on, the signal routing is correct, the source is active, and the volume is turned up. Connect a known working test speaker to the amplifier outputs; if there is still no sound, the issue is with the electronics. If there is sound, the problem lies in the wiring.

Poor low frequency response often indicates that the speakers are wired out of polarity. Verify that the amplifier positive terminal is connected to the red speaker terminal and the negative terminal is connected to the black speaker terminal. If using a subwoofer, ensure the subwoofer input panel is correctly wired.

Constant noise usually points to a defective amplifier or other electronic device in the signal chain. Alternatively, it may be caused by poor system grounding or a ground loop, which should be checked and corrected.

The 70V settings are 60 W, 30 W, 15 W, 8 W, and 8 Ω. The 100V settings are 60 W, 30 W, 16 W, and 8 Ω.

The recommended high-pass setting is 60 Hz at 24 dB/octave.

The ELECTRO-VOICE EVID-S5.2XB is IP65 rated per IEC-60529.

The nominal impedance of the ELECTRO-VOICE EVID-S5.2XB is 8 Ω.

The minimum impedance of the ELECTRO-VOICE EVID-S5.2XB is 6.5 Ω.

The dimensions are 255 mm x 180 mm x 148 mm (10.0 in x 7.1 in x 5.8 in), excluding the U-Bracket.

The net weight of the ELECTRO-VOICE EVID-S5.2XB is 3.2 kg (7.1 lb), excluding the U-Bracket.

The connectors support a maximum wire size of 12 AWG (2.05 mm diameter).

Yes, the ELECTRO-VOICE EVID-S5.2XB features a safety cable loop for added security.

The power handling is 75 W continuous pink noise (100 hours) with a 300 W peak.

Yes, the ELECTRO-VOICE EVID-S5.2XB U-Bracket can be installed to a threaded rod.

Yes, the ELECTRO-VOICE EVID-S5.2XB U-Bracket can be installed to a pole mount using steel band clamps.

The ELECTRO-VOICE EVID-S5.2XB U-Bracket can be installed to a junction box using a 0.25 inch rubber grommet for wiring.

The coverage angle of the ELECTRO-VOICE EVID-S5.2XB is 90 degrees horizontal and 90 degrees vertical.

No, the ELECTRO-VOICE EVID-S5.2XB cannot be painted when used in UL1480, ULC-S541, or EN54-24 fire installations.

Yes, for UL1480, ULC-S541, and EN54-24 fire installations, the weather cover must be used.

No, for UL1480, ULC-S541, and EN54-24 fire installations, the ELECTRO-VOICE EVID-S5.2XB is not intended for connection to DC supervised systems.

The sensitivity of the ELECTRO-VOICE EVID-S5.2XB is 89 dB (half-space, on wall, averaged 100 Hz to 10 kHz, 1 W).

This product must be disposed of separately from household waste according to local laws and regulations to allow for reuse and recycling.

Yes, it is suggested to install an extra suspension point back to the building structural supports with as little slack as possible, preferably less than 1 inch.

The ELECTRO-VOICE EVID-S5.2XB features a 5.25 inch woofer that provides extended LF performance down to 55 Hz.

The calculated maximum SPL of the ELECTRO-VOICE EVID-S5.2XB is 108 dB (114 dB Peak).

The packing list includes 2 speakers, 1 Allen wrench, 4 safety screws for the U-Brackets, 2 U-brackets, 2 weather covers, 8 weather cover screws, 2 spare grille logos, and 1 installation manual.

The U-Brackets can be mounted using a standard 2-inch or 4-inch U-Bolt.

The ELECTRO-VOICE EVID-S5.2XB is IP65 rated, designed to withstand the toughest weather conditions.

The rated frequency range for UL1480/ULC-S541 installations is 400 Hz to 4 kHz.

The rated frequency range for UL1480A/CSA C22.2 NO. 205 installations is 55 Hz to 20 kHz.

The enclosure and baffle of the ELECTRO-VOICE EVID-S5.2XB are made of UL 94-5VB fire rated ABS plastic.

Yes, in Canada you must follow CSA C22.1 and ULC-S524. In the United States, follow the National Electrical Code NFPA 70 and NFPA 72. In the EU, follow national electrical codes.

The ELECTRO-VOICE EVID-S5.2XB uses a removable locking 4-pin connector (Euroblock).

No, connections for the ELECTRO-VOICE EVID-S5.2XB shall not be made with rigid conduit but with flexible conduit or wiring only.

The ELECTRO-VOICE EVID-S5.2XB utilizes a two-way design, internally damped, with a passive crossover.

Clean the surface with alcohol before applying the new logo.

If the connection is clean and tight but the problem persists, the issue might be in the amplifier or the wiring. Connect a test speaker in parallel to test each connection point along the line.

Yes, a 5-mm Allen wrench is provided with the ELECTRO-VOICE EVID-S5.2XB.

The shipping weight of the ELECTRO-VOICE EVID-S5.2XB package is 9.5 kg (21.0 lb).

The grille for the ELECTRO-VOICE EVID-S5.2XB is made of power-coated Aluminum.

Yes, the ELECTRO-VOICE EVID-S5.2XB has a 60 W transformer with an 8 Ω pass-through.

Yes, the ELECTRO-VOICE EVID-S5.2XB is engineered for the toughest weather conditions and is IP65 rated, making it suitable for both indoor and outdoor applications.

If the sound is very weak, the line may have a short circuit, possibly caused by a scrape, pinch, or staple puncture.

If the test speaker produces sound at a normal level when connected in parallel, but the main line is silent or weak, the wire is likely open, indicating a cut wire or missed connection.

The high frequency transducer size of the ELECTRO-VOICE EVID-S5.2XB is 0.75 in (20 mm).

The low frequency transducer size of the ELECTRO-VOICE EVID-S5.2XB is 5.25 in (133 mm).

Yes, the ELECTRO-VOICE EVID-S5.2XB is available in black (RAL 9004) or white (RAL 9003).

The frequency response (-3 dB) of the ELECTRO-VOICE EVID-S5.2XB is 90 Hz to 20 kHz.

The sensitivity (SPL 1 W / 1 m) of the ELECTRO-VOICE EVID-S5.2XB for UL1480/ULC-S541 installations is 87 dB.

In UL1480/ULC-S541 installations, the power handling of the ELECTRO-VOICE EVID-S5.2XB at 8 ohms is 30 W.