Click here to download ELECTRIQ EIQ-3MS9K9K9K (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Wall Mounted Inverter Multi Split Air Conditioner with Heat Pump User and Installation Manual eiQ-3MS9K9K9K electr Thank you for choosing ElectrlQ Please read this user manual before using this innovative Air Conditioner and keep it safe for future reference. Visit our page electrIQ.co.uk for our entire range of Intelligent Electricals

****** Page 2 ****** CONTENTS SAFETY INSTRUCTIONS OPERATION REMOTE CONTROL FILTERS END OF SEASON START OF SEASON REPLACING THE BATTERIES INSTALLATION GUIDE INSTALLATION OF THE OUTDOOR UNIT PIPELINES CONNECTION & AIR PURGING ELECTRICAL CONNECTION OF THE AIR CONDITIONER TROUBLESHOOTING AND SELF DIAGNOSIS TECHNICAL SPECIFICATIONS APPENDIX IMPORTANT NOTE: 3 4 5 8 8 8 8 9 15 16 19 20 22 23 This air conditioner is supplied in multiple boxes. Before an engineer visit is confirmed, ensure that all the boxes required have been received in good condition and the codes on each box matches your model on the table below: Model eiQ-3MS9K9K9K Outdoor QTY Indoor eiq-9wminv3MSlN Pipekit eiq- 3MSC2XWlNSOUT 1 QTY Eiq- 3 9wminvlN5m* QTY 3 The retailer and manufacturer will not be liable for failed installation, or problems occurring due to the above not been checked prior to arranging installation. *PIPEKITI 2K-5M may also be supplied, which is the same specification. A range of pipe kits and pipes are available from the retailer. Longer pipes will require the addition of refrigerant by an F-gas registered engineer. 2

****** Page 3 ****** SAFETY INSTRUCTIONS Important! • Carefully read the instructions before operating the unit This appliance comprises of three indoor units and an outdoor unit. The slim wall mounted evaporators are designed exclusively for indoor installations while the external condenser should be installed outside, ensuring it is kept away from flood water or snow lines. Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed power source. • Installation must be in accordance with the regulations of the country where the unit is used. • These air conditioners are supplied with refrigeration pipes and electrical cables. European Union regulations requires for an F-Gas trained engineer to handle any operation where non-qualified intervention could case fluorinated gas to escape. A commissioning certificate must be issued with any installation. If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician. This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care. Disconnect the power before dismantling, assembling or cleaning. • Avoid touching any moving parts within the appliance. • Never insert fingers, pencils or any other objects through the guard • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Do not leave children unsupervised with this appliance. • Do not clean the unit by spraying it or immersing it in water. Never connect the unit to an electrical outlet using an extension cord. The outdoor must be hardwired by a qualified electrician. • Never operate this appliance if the cord is damaged. Ensure the power cord is not stretched or exposed to sharp objects or edges. • A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard. Any service other than regular cleaning or filter replacement should be performed by an authorized service representative or a qualified air conditioning engineer. Failure to comply could result in a voided warranty. • Do not use the appliance for any purpose other than its intended use. • The outdoor part of the air conditioner unit must always be stored and transported upright, otherwise irreparable damage may be caused to the compressor; if in doubt we suggest waiting at least 24 hours before starting the unit. • Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off. This prevents damage to the compressor. • Never use the mains as a switch to start and stop the air conditioning unit. Use the provided ON/OFF button located on the remote control. • Always place the unit on a dry and stable surface. Install the outdoor unit on a wall using wall mounting brackets or fix to a floor slab with special floor mounting fittings away from flood or snow lines. The indoor unit should not be installed in damp environments such as laundry or wet rooms 3

****** Page 4 ****** Energy Saving and Unit Safety Protection Tips Do not cover or restrict the airflow from the outlet or inlet grills. For maximum performance the minimum distance from a wall or other objects should be 50cm. Keep the filters clean. Under normal conditions, filters should only need cleaning once every four weeks (approximately). Since the filters remove airborne particles, the frequency of cleaning is dependant on the air quality. During the initial start up set the fan speed to maximum and the thermostat to 4-5 degrees lower than the current temperature. After, set the fan speed to low and set the thermostat to your desired setting. To protect the unit we recommend not using the cooling function when the ambient indoor temperature is higher than 350C. To protect the unit we recommend not using the heating function when the indoor ambient temperature is lower than 7 oc. Note the manufacturer operating temperature ranges at the end of this user manual. OPERATION Cooling The compressor (6) in the exterior unit compresses the refrigerant into a high- temperature, high-pressure gas. When this gas flows along the cooling fins of the condenser (7), heat is exuded and the gas condenses into a liquid, which is led to the evaporator (1 ) within the indoor unit. The liquid expands into a gas at a low temperature and low pressure is converted. This gas absorbs the warmth from the air in the room, the cooled air is blown back into the room and the heat is moved to the compressor along with the gas. A fan (3) draws the air over the filter and blows the cooled air back into the room. A fan (8) draws air over the condenser and blows warm air away. 1. Evaporator 2. Filter 3. Evaporator Fan 4. Gas Line 5. Liquid line 6. Compressor 7. Condenser 8. Condenser Fan Heat Pump Mode The system operates in reverse: the condenser works as an evaporator, the evaporator as a Mode condenser: warm air is blown into the room. It is ideal as a maintenance heating when outside temperatures are not too low and when the indoor temperature is above 7 oc. Dehumidifying As with cooling, the moisture in the air condenses on the cold evaporator at room temperature acting as a powerful dehumidifier. NOTE: This is a multisplit system and multiple indoor units are connected to a single outdoor compressor. Please make sure that the indoor units are set to operate in same mode. Multiple indoor units connected to the same compressor cannot operate in different modes at the same time although you are able to set different target room temperatures for each unit. Fan only mode can be operated while other units are in heating or cooling.dd 4

****** Page 5 ****** REMOTE CONTROL SWING indicator AUTO indicator COOLING indicator DRYING indicator HEATING indicator indicator AIR FLOW indicator SET TEMPERATURE button This button sets the room temperature. MODE button This button changes the operation mode: AUTO, COOL, DRY, HEAT, FAN. SWING button This button turns on and off the veftical swing function AIR FLOW button This button turns on and off the horizontal swing function TIMER button This button is used to tum on and off the timer QUIET button This button sets the unit to run at a low fan speed to reduce operational noise Temperature indicator indicates the set temperature TIMER QUIET o 0—>GF TURBO CLEAN SLEEP IONIZER LIGHT HOLD SLEEP indicator indicates during sleep operation TURBO indicator indicates during turbo operation QUIET indicator Key lock indicator IONIZER indicator FAN SPEED indicator Indicates the fan speed selected ON/OFF button Press to turn On / Off the air conditioner FAN SPEED button To change between Low, Medium, high and AUTO fan speeds. TURBO/CLEAN button When the AC is powered on. this button changes to TURBO operation(it doesn’t work in AUTO. DRY and FAN mode. When the AC is powered off. this button changes to CLEAN operation: the AC will be powered on and gets into the cool,25Xt , high fan speed mode. SLEEP button This button changes to SLEEP operation. IONIZER button This button changes to IONIZER operation. LIGHT/HOLD button Short Press: Turn the display On/Off Long Press. Lock / Unlock the remote The remote control has a range of up to 8m. Point the remote control at the receiver in the indoor unit. A beep confirms that the remote control signal has been received. NOTE: The LIGHT, IONISER and CLEAN functions may not be available on all models REMOTE OPERATION Turn the appliance on with the ONIOFF button. This starts the unit with the last used settings. The ON/OFF button will also turn off the air conditioner. TEMPERATURE The desired temperature is set using the up and down buttons, within the range of 160C 5 320C.

****** Page 6 ****** FAN SPEED Use this button to set the fan speed between low, medium, high and automatic (the corresponding symbol on the display will flash). The fan speed in the automatic setting is determined by the difference between the desired temperature set and the room temperature. COOLING MODE 1. Repeatedly press the MODE button until the COOL indicator appears. 2. Set the desired temperature using the TEMPERATURE up and down buttons. 3. Use the FAN SPEED button to set the fan speed. HEATING MODE 1. Repeatedly press the MODE button until the HEAT indicator appears 2. Set the desired temperature using the TEMPERATURE up and down buttons. 3. Use the FAN SPEED button to set the fan speed. FAN MODE 1. Repeatedly press the MODE button until the FAN indicator appears. 2. The temperature settings will not affect the fan operation 3. Use the FAN SPEED button to set the fan speed. DEHUMIDIFY MODE 1. Repeatedly press the MODE button until the DEHUMIDIFY indicator appears. 2. The FAN button does not work in dehumidify mode. The fan speed will always be low in this mode. Also temperature cannot be adjusted in dehumidifying mode AUTO MODE 1. 2. 3. 4. 5. 6. Repeatedly press the MODE button until the AUTO indicator appears. Set the desired temperature under auto mode to the required level between 16—32 oc The difference between the set temperature and the room temperature determines how the air conditioner operates: cooling, heating or fan. Once the temperature is set in auto mode it is not possible to amend it. It the desired temperature requires changing, change the unit out of Auto mode before changing it back. The unit will operate in the auto selected mode until set temperature is reached than switches the compressor off. Mode is locked until reset via mode button. You can use the FAN button to set the fan speed while in Auto mode. All indoor units must be operating in the same mode, otherwise a mode mismatch error will show. SLEEP MODE During sleep mode the unit will operate with a low fan speed to minimise the operational noise of the unit. 1. Press the SLEEP button 2. Set the desired temperature. 3. Press the SLEEP button; SLEEP indicator will appear on the display. Cancel the sleep mode by pressing this button again. CLEAN (Not available on all models) When pressed while the unit is in standby mode, the unit will power on in high speed fan mode, and run through the cleaning mode, before returning to standby mode. 6

****** Page 7 ****** TURBO (Not available on all models) When pressed the unit will operate at maximum fan speed and maximum cooling for 15 minutes. 1. Set the air conditioner to run with the settings required after Turbo has completed. 2. Press the TURBO button. TIMER OFF FUNCTION (While the air conditioner is on) 1. Ensure the air conditioner is turned on and running with your desired settings 2. Press the TIMER button to turn on the timer. 3. Use the up and down button to set the timer between 1 and 24 hours. 4. Once the time you have set has elapsed, the appliance will switch itself off. 5. To cancel the timer function before the set time has elapsed, press the TIMER button again. ON FUNCTION (while air conditioner is in standby) 1. Ensure the air conditioner is in standby mode. 2. Press the TIMER button to turn on the timer. 3. Use the up and down button to choose from 1-24 hours timer setting. 4. Set the desired operation, temperature, fan speed, etc. 5. Once the time you have set has elapsed, the appliance will switch itself on. 6. To turn off the timer function before the set time has elapsed, press the TIMER on button again. IONISER (Not available on all models) When turned on the ioniser uses an electrical charge to remove particles from the air, improving air quality. QUIET BUTTON (Not available on all models) When activated the air conditioner will operate with settings such as low fan speed to minimise the operational noise. IMPORTANT AUTO RESTART: The air conditioner will automatically restart when electricity is restored after a power cut. If in doubt, check the settings. RANGE OF THE INTERNAL THERMOSTAT: The internal thermostat can be set at a desired temperature between 16 and 320C. Note that whether the desired value can be achieved depends on a number of factors including the units power, room size, temperature and insulation of the room. RANGE OF HEAT PUMP FUNCTION: The heat function can be used when the external ambient temperature is 50C or higher. The performance of the heat pump will degrade as the external temperature reduces. CAPACITY: The required cooling or heating capacity depends greatly on the location and/or use of the room where the air conditioner is installed. Strong sunlight and the presence of people, lights or equipment create an additional heat load. Normal living spaces require about 100 W per square metre of floor surface. In strong sunlight or if other sources of heat are present, this may be as much as 350 W/sqm. Tip: On warm days, let the air conditioner cool the room as much as possible during the night and set the temperature constant from night to daytime. EMERGENCY START: In the event of a problem, the air conditioner can be operated using the emergency button under the panel in the indoor unit. Open the front panel and press the button, the air conditioner will: -heat if the room temperature is 20 oc or less, cool if the room temperature is 25 oc or more and for values in between will dehumidify. 7

****** Page 8 ****** FILTERS Turn off the appliance from the consumer unit before attempting to service the filters. Opening the front panel: at the A recesses, pull the front part up with both hands. The front panel will stay horizontal (at around 900). Closing the front panel: press the front part down at the sides at B and in the middle at. Make sure it is properly closed (click). Hold the front panel open (or put it in horizontal position) and remove the filter(s). 2. 3. 4 Use a vacuum cleaner to remove dirt. If the dust filter is very dirty, it may be washed in lukewarm water with a very small amount of neutral detergent. Rinse well and allow to dry completely (not in direct sunlight or near a source of heat). Keep the grid panel open and reinstall the filter(s). Press the panel shut; a click indicates it is closed properly. Restore the power from the consumer unit and turn the air conditioner on. Indoor Unit: While the unit is disconnected from power dust regularly with a dry cloth or slightly damp paper towel. Never use chemicals or solvents. Never spray a liquid in or over the appliance. Exterior unit: While the unit is disconnected from power. Remove dirt and keep the air intake and exhaust openings free of debris, etc. Cleaning with chemicals may cause damage. END OF SEASON If the air conditioner is not going to be used for an extended period: • Set in fan mode on a warm day so that the inside of the appliance fully dries out. • Switch off the power from fuse box and remove the batteries from the remote control. • Clean the filters START OF SEASON If the air conditioner is to be used again after an extended period: • Check that the air intake and exhaust openings of the indoor and exterior units are not blocked. Remove any dirt and debris. • Check that the filters are installed and are clean. • Check that the condensation outlet drains properly and there is no dirt or organic blockage (otherwise leakage may occur) • Install 2 AAA batteries in the remote control. • Turn the appliance on, set the time and desired settings. REPLACING THE BATTERIES • Remove the battery cover. • Replace the AAA batteries, following the markings for the polarity • Replace the battery cover. • Press the on/off button; if no symbols appear on the display, the batteries are empty or have been incorrectly installed. 8

****** Page 9 ****** INSTALATION GUIDE SAFETY Only qualified personnel should install this appliance. This installation manual is intended for use by individuals possessing adequate backgrounds and qualifications in electrical, electronic, refrigerant and mechanical fields. Any attempt to install or repair the appliance may result in personal injury and/or property damage. The manufacturer and retailer cannot be held responsible for the interpretation of this information, nor can it assume any liability in connection with its use. The units are designed for permanent installation. The equipment is designed for domestic or office use and we are not making any endorsements for its use in industrial or maritime environments. Do not place near sources of heat, vapours, industrial machine oil or other flammable gases. High frequency waves generated by radio equipment, welders and medical equipment will interfere with the normal operation of the unit. Install this device only when it complies with local/national legislation, ordinances and standards. Check the mains voltage and frequency. This unit is only suitable for an earthed electrical supply, connection voltage 230 V- / 50 Hz. The information, specifications and parameter are subject to change due to technical modifications or improvement without any prior notice. The accurate specifications are presented on the nameplate label. Please read this installation manual completely before installing the product. When the power cord is damaged, replacement work shall be performed by authorized personnel only. Installation work must be performed in accordance with all European, national and / or local directives and standards and must be done by authorized personnel only. Always make sure to wear the correct personal safety protections such as protective eyewear, gloves, ear protection etc. This air conditioner contains a refrigerant and can be classified as pressurized equipment. Therefore always contact a qualified air conditioning engineer for installation and maintenance of the air conditioner. The air conditioner must be inspected and serviced on an annual basis by a qualified air conditioning engineer. For your convenience you can download the latest version of the user / installation manual from electriq.co.uk INDOOR UNIT POSITION The air inlet and outlet vents should be away from any obstruction, ensuring that there is a good airflow through the whole air-conditioned space. • Select a position where the condensing water can be easily drained out, and the indoor unit can be easily connected to outdoor unit. The wall where the unit is fixed should be strong enough to withstand the full weight and vibration of the unit. The unit should be accessible for service and maintenance. The height of the installed unit should be ideally more than 200cm from floor. The air conditioner must not be installed in a wet environment such as a bathroom, shower or swimming pool etc. 9

****** Page 10 ****** OUTDOOR UNIT POSITION A convenient position, dry and well ventilated, outside of direct sunlight or strong winds, which is not on flood line and where noise and airflow does not cause interference or inconvenience. Select a location where there should be no obstructions to the inlet and outlet vents. The location should be able to withstand the full weight and vibration of the outdoor unit and permit safe installation. Make sure that the outdoor unit installation is made in respect to installation dimension diagram with easy maintenance access. Select a place where it is out of reach of children. Do not block utilities access or fire escapes. The external unit must be lifted and put in place by two people or by specialised equipment. NOTES: • Only use the correct power supply voltage making sure the correct sized power cables are used • The appliance shall be installed in accordance with standard wiring regulations by qualified personnel. • Only replace fuses according to their printed rating or corresponding pcb boards. RECOMMENDED INSTALLATION SPACING DIAGRAM Space to the ceiling Space to the wall 5cm Abov Sp 5cmAbov tot e wall 15 cm Above ooc Abov Air outlet side 250 cm bov Space to the floor The dimensions of the space necessary for correct installation of the appliance including the minimum permissible distances to adjacent structures Space to the obstruction 200 cm. 2. Either the indoor unit or the outdoor unit can be higher, but the height difference must comply with a max. 5 metres level difference. 3. Try to avoid the bending of the pipes as much as possible so as to prevent possible negative impacts upon the performance of the unit. INSTALLATION OF THE OUTDOOR UNIT External connection Gas side pipe electric wire Liquid side piping Gas side piping insulation Finally wrap It Liquid side Piping insulation Fig.l Right—- Right rear Water drainage pipe with ta e Left rear Left Fig .2 Mounting Fixing hook Mounting plate Fig.3 Fig.4 Bottom hooks Bracket Top hooks Hook supports Try to move the product to the installation location in its original packaging to prevent damage. As the gravity centre of the unit is not at the installation centre, special caution should be taken when using hoisting cables to lift the unit. During transport, the outdoor unit must not be tilted in excess of 45 degrees (also do not store the unit horizontally. Use expansion bolts to fix the mounting supports to the wall; Use bolts and nuts to fix the outdoor unit firmly on the support, ensuring the installation is level; if the unit is installed on a wall or a rooftop, the supports have to be firmly fixed so as to resist earthquake or strong wind. Dimensions for parallel indoor units installations 300 mm(l ‘)min 15

****** Page 16 ****** PIPELINES CONNECTION & AIR PURGING No dust or any other particles, air or moisture should be allowed to enter the air conditioning system. Careful attention should be paid when the pipeline connection of the units are made. Try to avoid repeated curves as much as possible; otherwise damage to the copper pipes may occur. Suitable wrenches should be used when the pipeline connection is done so as to ensure the appropriate torque is applied (refer to following torque table). Excessive torque action might damage the joints while too little torque might lead to leakage. Torque based upon the wrench to be used Copper pipe diam. 6.35(1/4″) 9.52(3/8″) 12.7(1/2′) 15.88(5/8″) 19.05(3/4″) Tightening torque 160kgf.cm(63kgf.inch) 300kgf.cm(118kgf.inch) 500kgf.cm(197kgf.inch) 750kgf.cm(295kgf.inch) 200kgf.cm(472kgf.inch) Strengthened tightening tor ue 200kgf.cm(79kgf.inch) 350kgf.cm(138kgf.inch) 550kgf.cm(216kgf.inch) 800kgf.cm(315kgf.inch) Nutof 1400kgf.cm(551kgf.inch) connection Dii* If you are installing a multisplit system with easy fit connectors follow the procedures below: 1. Remove the dust caps from the indoor and outdoor units and the connecting pipe. 2. Align the joint of the connecting pipe between the indoor and outdoor and tighten the connecting nut by hand to prevent cross threading. Secure them with a wrench, applying the maximum torque as shown in the table above. 3. Pressure test and vacuum pump the pipework. 4. Remove the two valve core caps from the outdoor unit and turn on the high and low pressure valve cores with an socket wrench, then tighten the two valve core caps of the outdoor unit. Finally you can wrap hot insulating tape around the joints of indoor and outdoor units Indoor unit Valve core cap Torque wrnch Spanner Joint Wrapping uith ittsulating cotton Low pressure valve High pressure valve AIR PURGING WITH VACUUM PUMP Outdoor unit Manifold gaug Prossurø gauge 3-way valve 2-way valve unjon nut Blank cap rging Valve stem Service hose Vacuum pump 1. 2. 3. 4. 5. Check that pipelines connection have been properly connected, remove the charging port cap, and connect the manifold gauge and the vacuum pump to the charging valve using service hoses as shown Open the valve on the low-pressure side of the manifold gauge, then run the vacuum pump. Vacuum the indoor unit and the connecting pipes until the pressure in them lowers to below 1.5mmHG (The operation time for vacuuming is about 10 minutes). When the desired vacuum is reached, close the low pressure valve on the manifold and stop the vacuum pump. Disconnect the service hoses and fit the cap to the charging valve. Remove the blank caps, and fully opens the spindles of the 2-way and 3-ways valves with a service valve wrench. Tighten the blank caps of the 2-way and 3-ways valves, applying the torque listed in the table above. 16

****** Page 17 ****** ADDING REFRIGERANT Refrigerant must be added if the pipework measures more than 5 metres (16’5″) in length. This operation can only be performed by a professional F-Gas engineer, for the additional refrigerant quantity, please refer to the table. GAS LEAKAGE INSPECTION ADDITIONAL REFRIGERANT AMOUNT Liquid pipe diameter 6.35 (1/4″) (pipework length – 5)m x 30g After the pipeline connection is done, use a leakage inspection device to carefully check if there is any leakage at the joints. This is an important step to ensure the quality of installation. Once a leak is detected, proper action should be taken immediately. 1. 2. 3. Install the water drainage pipe For good drainage, the drain hose should be angled downwards. Do not pull on or bend the drain hose or flood its end with water. When the long drainage hose passes through indoor areas, it should be wrapped in insulation to prevent condensation building. Wrenched Bent Flooded

****** Page 18 ****** To avoid damaging the pipework during unrolling Ensure the packed soft pipes are vertical before extendin Please make use of a semicircle pulley to keep the allowed bending angle Please use a twisting wheel to avoid improper bending. Please use a rigid elbow to maintain the bending angle while soft pipes operating. Avoid bending the pipe where possible, where bends are necessary their radius should be kept as large as possible. Please do not extend only one side of the pipework, as this could kink or dama e the i ework Ensure the bends are not too severe, as this could restrict refrigerant flow, reducing performance or preventing operation. Over bent soft pipes will lead to irregular bending Do not use short sharp angle bends. Notes: Please ensure you use the protective plastic tube and sleeves before passing the copper pipes through the wall in order to avoid pipe damage. 18

****** Page 19 ****** ELECTRICAL CONNECTION OF THE AIR CONDITIONER The electrical connections can be found under the protective plastic cover. Remove this from the side of the outdoor unit to gain access to the electrical connections. Connect the indoor power and control wires with the matching outdoor wire as per the electrical diagram. Do not attempt to connect the wires in a different way to the diagram on the air conditioner as this could damage the unit and invalidate the warranty. Secure the wires and replace the cover before operating the unit. The appliance should be installed in accordance with national wiring regulations. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a suitably qualified person in order to avoid a hazard. The unit is designed to be hard wired and a suitable switch with a contact separation of at least 3mm in all poles must be added to the fixed wiring. Note: in some models you may connect the indoor wire connector with an optional outdoor defrost probe The air conditioner electrical wiring must follow the specific country regulations. If power cord is damaged must be replace by a qualified electrician. There are only three thread buckles on the electric box connection plate, o The left one is for the power line. o The middle one is for the cables for both Unit-A and Unit-B. o The right one is be used for Unit-C’. (Unit C) cn z (Unit B) 19 (Unit A) 220&240V, 50HZ TO POWER LEFT RIGHT

****** Page 20 ****** TROUBLESHOOTING AND SELF DIAGNOSIS ElectriQ air conditioners have an advanced self-diagnosis system allowing them to display the service information Protection and Fault Codes for Indoor Unit Board Fault/Protection Zero passage fault of PG motor Indoor and outdoor communication fault Tr sensor fault Tp sensor fault Indoor fan fault PM 2.5 sensor fault(the function is not available for multi-split air conditioning system) Outdoor module fault Outdoor ambient temperature sensor fault Outdoor coil temperature sensor fault Compressor suction temperature sensor fault Compressor exhaust temperature sensor fault Current and Potential transformer fault Compressor drive fault Power phase sequence fault or open phase fault Air return sensor fault Outdoor DC fan fault Multi-split mode conflict protection Fault cause Abnormal zero passage of PG motor Abnormal communication between indoor unit and outdoor unit Open circuit or short circuit of Tr sensor Open circuit or short circuit of Tp sensor Malfunction of indoor fan Open circuit or short circuit of PM 2.5 sensor(the function is not available for multi- split air conditioning system) Malfunction of outdoor module Open circuit or short circuit of outdoor temp sensor Open circuit or short circuit of outdoor coil temp sensor Open circuit or short circuit of compressor suction temp sensor Open circuit or short circuit of compressor extraction temp sensor Malfunction of current and potential transformer Malfunction of compressor drive Power phase sequence fault or open phase fault Open circuit or short circuit of air return sensor Malfunction of outdoor DC fan Multi-split mode conflict protection 20 Indoor Display

****** Page 21 ****** OUTDOOR BOARD FAULT CODES Displayed Content EEA EEB EC EOA EOB EOC EOD EOE EIO EU E-tA EtB Etc EtD EtE HI Fault Definition EEPROM fault EEPROM fault Fault of communication between coordination board and driver board Fault of communication between variable frequency module and outdoor unit 1# indoor communication fault 2# indoor communication fault 3# indoor communication fault 4# indoor communication fault 5# indoor communication fault Weak current communication fault Variable frequency drive/module fault Compressor shell roof switch fault Volta e sensor fault T3 temperature sensor fault T4 temperature sensor fault Exhaust temperature sensor fault Air return temperature sensor fault 1#T2B1 temperature sensor fault 2#T2B2 temperature sensor fault 3#T2B3 temperature sensor fault 4#T2B4 temperature sensor fault 5#T2B5 temperature sensor fault IPM module rotection Com ressor drive fault rotection HP dial setting fault Low-volta e rotection Com ressor current rotection Exhaust gas high temperature rotection High-voltage switch rotection Low-volta e switch rotection Refrigerator T 3 overheat protection Fault Cause Fault of EEPROM on coordination board Fault of EEPROM on outdoor board No communication or communication fault between coordination board and driver board Communication fault between the outdoor unit power board and module No communication or communication fault between 1# indoor and outdoor No communication or communication fault between 2# indoor and outdoor No communication or communication fault between 3# indoor and outdoor No communication or communication fault between 4# indoor and outdoor No communication or communication fault between 5# indoor and outdoor Communication fault of coordination board and outdoor unit board Driving occurs 3 times within 30 minutes or module rotection Too high temperature or the shell top of compressor or tem erature switch is broken The s stem is unable to sense volta e Short circuit or open circuit of outdoor coil temperature sensor Short circuit or open circuit of outdoor ambient temperature sensor Short circuit or open circuit of exhaust temperature sensor Short circuit or open circuit of air return temperature sensor Short circuit or open circuit of outlet temperature sensor of 1# outdoor coil Short circuit or open circuit of outlet temperature sensor of 2# outdoor coil Short circuit or open circuit of outlet temperature sensor of 3# outdoor coil Short circuit or open circuit of outlet temperature sensor of 4# outdoor coil Short circuit or open circuit of outlet temperature sensor of 5# outdoor coil Com ressor drive module is in abnormal status Com ressor drive is in abnormal status or unable to star The type of driver board does not match that of compressor In ut volta e is lower than 160V?5V Running current exceeds the set value Exhaust temperature exceeds the shutdown protection value High-voltage switch is in abnormal status Low-volta e switch is in abnormal status Outdoor pipe temperature of refrigerator exceeds the set value 21

****** Page 22 ****** TECHNICAL SPECIFICATION Model (Ph-V-Hz) Rated volt and frequency Recommended Circuit Breaker Size Mode Single Rated capacity (W) Triple Single Cooling power input (W) Triple Single Heating current input (A) Triple SEER/SCOP(W/W) Design load (W) T biv. (C) Heating balance point temperature T 01. Heating limit operating temperature thermostat-off mode (W) Stand by mode (W) Throttle type Annual Consumption (KW) Model 9K+9K+9K 220-240V-50Hz, 1 Ph Cooling 1240w-3840W 3000W-8500W 320w-1470W 620w-3950W 1.4—6.4A 2.8-18A 6.5/A++ 7000 cooling: 377 27A 92W heating: 0.5 EEV Heating 1400w-4000W 2500w-9000W 300w-1420W 580w-3900W 1.3-6.2A 2.7-17.7A 6300 -10 13W 2205 ATL232SDNC9AUY Compressor Type (Rotary Piston /scroll) Brand Capacity (W) Power input (A) RLA (A) Refrigerant oil a68HES- Outdoor Dimension (L *W *H) (mm) Packing (L *W *H) (mm) Net/Gross weight (kg) noise sound pressure level (dB/A) Sound power noise (dB/A) Refrigerant type/weight Defrost mode Rotary Highly 6535 2075 10.7 H or equivalent 880+20ml 970x370x790 1120x485x890 66/69 60 70 R41 OA/2800g INDOOR UNIT: Model Rated volt and frequency Cooling capacity (W) Cooling power input (W) Cooling current input (A) Ph-V-Hz) Automatic defrosting Indoor unit 220-240V-/50Hz 2600W(1240-3840W) 810W(320-1470W) 3.5A(1.5-6.7A) 2700W(1400-4000W) 790W(300-1420W) 3.4A(1.4-6.6A) Indoor Air Circulation (m3/h) Dimension (L *W *H) (mm) Packing (L *W *H) (mm) Indoor Net/Gross weight (kg) noise sound pressure level (dB/A) Sound power noise (dB/A) Liquid side/ Gas side/Length (mm) Refrigerant Max. refrigerant pipe length [Max. piping difference in level 550m3/h 780076002 930x367x295 10/12 30-38 (96.35+9952)x5000 20m/10m Due to continuous product development process specification may change. These units contain a gas governed by F-Gas regulations. The gas must be handled by qualified F-Gas engineers. 22

****** Page 23 ****** APPENDIX Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres. WARRANTY INFORMATION The ElectriQ guarantee provides cover against material or manufacturing faults. This means that if your air conditioner develops a fault during the guarantee period, we will arrange for it to be repaired or replaced. Faults arising from a faulty installation are specifically excluded. The system must be serviced annually by qualified personnel. This unit must be operated under conditions as recommended in this user manual, at voltages indicated on the unit. Any attempts made to service or modify the unit by unqualified person, will render this WARRANTY VOID. This warranty is in addition to, and does not affect, your statutory rights. Our warranty is R TB warranty and cover parts and labour only. We recommend that you note the details of your purchase below and retain your original proof of purchase receipt with this manual. Keep these documents safe in the event of a warranty claim. Purchase Date: Retailer name: Model number: Serial number: Installation Date: Installer name: Service Date: Engineer/ Company name: 23

****** Page 24 ****** ElectrlQ UK SUPPORT ElectrlQ.co.uWsupport Please, for your own convenience, check the troubleshooting guide before calling the service line. If the unit still fails to operate call: 0871 620 1057 or complete the online form Office hours: 9AM – 5PM Monday to Friday ElectrlQ.co.uk Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA 24

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELECTRIQ EIQ-3MS9K9K9K (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.