Click here to download ELECTRIQ EIQ-32MCV4KAFSHDR (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** USER MANUAL 32 INCH CURVED LED MONITOR eiQ-32MCV4KAFSHDR Thank you for choosing electriQ Please read the user manual before using this monitor and keep it safe for future reference Visit electriQ.co.uk to view our entire range of Intelligent Electricals

****** Page 2 ****** CONTENTS SAFETY PARTS LIST STAND INSTALLATION WALL MOUNT INSTALLATION CONNECTIONS AVAILABLE GETTING STARTED MONITOR CONTROLS INITIAL SET UP SHORTCUT BUTTONS MENU OPTIONS INPUT SOURCE BRIGHTNESS / CONTRAST COLOUR SETTINGS PICTURE QUALITY SETTINGS DISPLAY AUDIO MULTI WINDOW OSD OTHER TECHNICAL SPECIFICATION TROUBLESHOOTING SUPPORT 2 3 5 6 7 8 8 8 9 9 9 10 10 11 12 13 13 14 15 16 17 18 18

****** Page 3 ****** SAFETY INFORMATION Read these instructions All the safety and operating instructions should be read before this product is operated. Keep these instructions – The safety and operating instructions should be retained for future reference. Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to. Follow all instructions All operating and usage instructions should be followed. Do not use this equipment near water, or in humid environments – The appliance should not be used near water or moisture e.g. in a wet basement or near a swimming pool. Clean only with a dry cloth. Do not use solvents or petroleum-based fluids. Do not block any ventilation openings. Do not install near any heat sources such as radiators, stoves or other apparatus (including amplifiers) that produce heat. Do not tamper with the supplied plug. This plug is a BS1363 standard plug. Protect the power cord from being walked on or trapped, particularly at the plug and at the point where it exits from the appliance. Only use attachments/accessories specified by the manufacturer. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart or stand is used, use caution when moving it to avoid any injuries or damage from it tipping over. Unplug the apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as if the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or it has been exposed to rain or moisture, it does not operate normally or has been dropped. Please keep the unit in a well-ventilated environment. The monitor should only be connected to a mains power supply as rated on the back of the equipment. To prevent overload, do not share the same power supply socket with too many other electronic components. Do not place any connecting wires where they may be stepped on or tripped over. 3

****** Page 4 ****** Do not place heavy items on the cable as this may cause damage. When removing from a socket hold by the plug and not the wires. Disconnect the power immediately and seek professional help if the plug or cable is damaged, liquid has spilt onto the unit, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the unit does not work normally. Do not remove the safety covers. There are no user serviceable parts inside. Trying to service the unit yourself is dangerous and may invalidate the product’s warranty. Only qualified personnel should service this apparatus. Do not block ventilation slots on the back cover. The monitor can be placed in a cabinet but ensure at least 5cm (2″) clearance all around. Do not tap or shake the screen, this may damage internal components. Due to our continuous product development, the operation and or features of the product received may vary slightly from the information provided within the manual. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus. WARNING: The wall plug socket is used as a disconnection device and should remain readily accessible. WARNING: The batteries shall not be exposed to excessive heat such as direct sunlight or fire. Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible. The availability of features and settings may vary depending on the input source and method of connection. AT FULL VOLUME, PROLONGED LISTENING MAY DAMAGE THE USER’S HEARING. CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN CAUTION: To reduce the risk of electric This warning sign is to shock, DO NOT remove the cover (or warn of dangerous back). No user serviceable parts inside. voltage inside the Refer servicing to qualified service product. personnel. 4 This warning sign is to alert you of important instructions accompanying the product.

****** Page 5 ****** PARTS LIST Monitor DP Cable Power Cable (AC 100-240/, Stand – Base 50/60Hz) Bolts x 4 (For Stand Assembly) USB Cable electri(.å ustn User Manual Stand — Upright Section 5 Extension Bolts x 4 (For Wall Mount Installation) Cable Clip

****** Page 6 ****** STAND INSTALLATION 1. 2. 3. Open the packing box, take out the upright section of the stand, cable clip and base. Use a screwdriver and one bolt to fasten the base to the stem. Cable clip Stand Base Bolts xl Use 2 x Bolts to secure the mounting plate to the rear of the monitor. Use both hands to stand the assembled monitor on a flat desktop. Button NOTES: • Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people. • electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases any guarantee will expire. • The stand can be removed from the rear of the monitor by pressing the quick release button on the rear of the monitor. 6

****** Page 7 ****** WALL MOUNT INSTALLATION The monitor is provided with mounting holes for a VESA approved wall mounting bracket (not supplied). Unscrew the 2 bolts on the mounting plate and press the button to remove the monitor from the bracket if mounting. M4 x12 bolts (not supplied) should be used to attach the bracket to the extension bolts. Do not use bolts longer than specified or damage will occur to the internal components. If the monitor is already attached to the stand, remove the stand. I Mounting plate NOTES: Bolts x4 Remove the original bolts x4 (1) from the opening in the back of the monitor. Follow the directions received with your mount, stand, or accessory and install the monitor on the wall or fixture as desired. Remember to use the included 4 extension bolts when mounting the monitor. Refer to image (2) for correct screw placement. Do not pinch the screen directly with your hand when hanging the product to prevent the screen from breaking. Due to the heavy weight and dimensions of LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people and professional installers are used to wall mount them (Wall mounting is optional). If you do not understand the instructions, or are unsure how to install this product, please contact a professional for assembly advice and assistance. Careful consideration should be made regarding the location the monitor is to be wall mounted as some walls are not suitable for installation. If the monitor is to be mounted on drywall, the mount must be anchored into a wooden stud, concrete block or brick behind the drywall. Installing on drywall alone may not support the weight of the display. When drilling holes, it is particularly important to take care of electrical cables, water or gas pipes in the wall. Please follow the instructions provided by the wall bracket manufacturer and ensure that all fixing screws supplied are used. electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases any guarantee will expire. 7

****** Page 8 ****** CONNECTIONS AVAILABLE ON THE MONITOR zOO 1 2 3 4 1. 2. 3. 4. GETTING STARTED MONITOR CONTROLS Power AUDIO OUTPUT DPI HDMI 1 – HDMI 2- HDM13 E Select signal source or Exit the menu Go Up within the Main Menu or increase the value of the selected item Go Down within the Main Menu or decrease the value of the selected item Enter the Main OSD Menu and Select submenu Turn the monitor On or Off 8

****** Page 9 ****** INITIAL SETUP (b 1 CONNECT THE MONITOR TO A POWER OUTLET 2 1. Press the POWER button on the monitor or to turn it on (The indicator will be blue) 2. Connect the relevant cable to the corresponding input on the monitor. The source will be automatically detected. SHORTCUT BUTTONS The monitor includes one touch options to access common settings. Main Menu Display Crosshairs Power Off RGB Range Scene mode switching MENU OPTIONS The menu for the monitor can be accessed by pressing the menu button on the control panel. This menu is separated into the following sub menus: Input source, Brightness/Contrast, Colour Settings, Picture Quality Settings, Display, Audio, Multi-Window, OSD (On screen display), and other. Details of each menu can be found in the following section. 9

****** Page 10 ****** OSD MENU INPUT SOURCE Signal HDM12 Input Source Brightness/Contrast Color Setting Picture Quality Setting Display Audio Multi-Window OSD DPI HDMII (20) • HDM12 (14) HDM13 (1.4) Windowl : Inputsource- HDMI 2 Resolution: 38400160@60Hz Resolution: 3840×2160@60Hz Window? Inputs ource: Resolution: Switch the signal input or select the source. DP, HDMII, HDM12, HDM13 BRIGHTNESS/CONTRAST HDMII Input Source BrightnesstContrast Color Setting Picture Quality Setting %play Audio Multi-VMndow Other Brightness Blacklevel Wirdowl : InputSource: HDMI 1 Resolution: 3840×2160@60Hz Resolution: 3840×2160@60Hz 90 50 50 off WLndow2′ InputSource: Resolutktnt Brightness Contrast DCR Black level Adjust the brightness of the display between O and 100. Adjust the contrast of the display between O and 100. Turn the Dynamic Contrast Ratio Feature On or Off. Adjust the black level of the display between O and 100. 10

****** Page 11 ****** COLOUR SETTINGS HDM12 Input Source Brightness/Contrast Color Setting Picture Quality Setting Display Audio Multi-Window Gamma Pictrue Mode Color Temperature Low Blue Light Hue Saturation Windowl : InputSource: HDMI 2 Resolution: 3440×2160@60Hz Resolution: 3840×2160@60Hz 2.2 Standard Warm 50 50 Window2: I nputSource: Resolution: OSD Other Gamma Picture Mode Colour Temperature Low Blue Light Saturation Change the Gamma value for the display between 2.0, 2.2 and 2.4. Change the picture mode between Standard, Photo, Movie, Game, FPS and RTS. Change the Colour Temperature of the display to Normal, Warm, Cool or User. When the User Mode is selected, the Red, Green, and Blue values can be adjusted independently between O and 100. Change the blue light emitted by the display betweenO and 100. Change the Hue value between O and 100. Change the Saturation of the display between O and 100. 11

****** Page 12 ****** PICTURE QUALITY SETTINGS HDM12 Input Source Brightness/Contrast Color Setting Picture Quality Setting Display Audio Multi-Window OSD Other Sharpness Response Time Noise Reduction Super Resolution Dynamic Luminance Control Sharpness Response Timen Noise Reductio Super Resolution Dynamic Luminous Control Windowl : InputSource: HDMI 2 Resolution: 3440×2160@60Hz Resolution: 3440×2160@60Hz 50 Off Off Off Off Windom: I nputSource : Resolution : Change the display Sharpness between O and 100. Turn the Response Over Drive feature between Off, High, Middle of low Adjust the level of Noise Reduction between Low, Medium, High, or Off. Change the Super Resolution value from O to 5. Turn the Dynamic Luminance Control Feature On or Off. 12

****** Page 13 ****** DISPLAY HDM12 Input Surce Brightness/Contast Color Setting Picture Quality Setting Display Audio Multi-Window OSD Other Aspect Ratio LED Mode AUDIO HDM12 Inp.n Brightress1Contrast Color Seting Picb-jre Quality Setting Audio Multi-Mndow OSD Mute Volume Audio Source ARpect Ratio Ledmode Window: : InputSource: HDMI 2 Resolution: 3440x2t60@60Hz Resolution: 3440×2160@60Hz Wide Screen Normal Window2: I nputSource: Resolution Change the image aspect ratio to Wide Screen Enter the monitors LED mode Mute Volume Audio Source Window’ : Inputsource: HDMI 2 Resolution: 3440×2160@60Hz Resolution: 3440×2160@60Hz Off 50 AutoSource Window2: InputSotrce: Resokltjon Turn On and off to mute and unmute the audio output. Adjust the output volume between 0 and 100. Chose which source the audio is output from. 13

****** Page 14 ****** MULTI-WINDOW HDM12 Input Source Brightness/Contrast Color Setting Picture Quality Setting Display Audio Multi-Window OSD Other Multi-Window Sub Win2 Input pp Size pp Position Swap Windowl : InputSource: HDMI 2 Resolution: 3840×2160@60Hz Resolution: 3840×2160@60Hz Off HDM12 Medium TopRight Window2 InputSource•. Resolution Choose the different formats of multi window display between Off, Multi-Window Picture in Picture (PIP) and Picture By Picture (PBP 2Win) Choose the source of the second window between HDMI 1, HDMI 2, Sub Win2 Input PIP Size PIP Position SWAP HDMI 3 and DP. Adjust the size of the secondary source in PIP and PBP modes between Small, Medium and Large Set the position of the secondary source in PIP and PBP modes between Top Right, Top Left, Bottom Right and Bottom Left. Swap the Primary and Secondary inputs on screen. 14

****** Page 15 ****** OSD HDM12 Input Source Brightness/Contrast Color Setting F)mlre Quality Setting Display Audio Mulü-Wlndow OSD Other Language OSD H-Position OSDV-Position OSD Transparency 00 Time Out OSD Rotation Windowl : InputSource: HDMI 2 Resolution: 3840×2160@60Hz Resolution: 3840×2160@60Hz English 50 50 20 20 Normal Window2: InputSource: Resolution: Language OSD H Position OSD V Position OSD Transparency OSD Time Out OSD Rotation Change the OSD Menu display language between English, Chinese, Korean, Russian, Spanish, Japanese and French. Change the horizontal position of the OSD Menu. Change the vertical position of the OSD Menu. Change the transparency value of the OSD Menu between O and 100. Change how long the OSD Menu is on before it automatically exits. Rotate the OSD Menu for ease of use on rotated screens. 15

****** Page 16 ****** OTHER HDMII Input Source Brightness/Contrast Color Setting Picture Quality Setting Display Audio Multi-Window OSD Other Free Sync Mode DP Version Reset HDR DP Version FreeSync(Adaptive Sync) HDR Reset Windowl : InputSource: HDMI 2 Resolution: 3840×2160@60Hz Resolution: 3840×1440@60Hz DP 1.2 Off Off Window? InputSource Resolution : Turn Free Sync On or Off. HDR: Turn HDR On (requires HDMI 2.0 input). Change the DP version Restore factory default setting. Turn the HDR on or off. 16

****** Page 17 ****** TECHNICAL SPECIFICATION Product Model Screen Size Panel Type Aspect Ratio Power Supply Power Consumption Dimensions Net / Gross Weight Maximum Resolution Brightness Static Contrast Response Time Viewing Angle (H/ V) USB Input USB 3.0 HDMI Input Display Port Input Audio Output Remote Control Working Temperature Working Humidity Speaker Specifications eiQ-32MCV4KVAFSHDR 32″ Diagonal VA Panel 16:9 AC 100-240V, 50/60Hz, 1.5A 46W(Typical) 712*505.6 *226.5 mm 7.07kg / 9.09 kg 3840*2160 350cd/m 2 3000:1 8ms 1780 / 1780 USB-B x 1, USB-A x 3 Compliant with USB 3.0 standards. If used with USB 2.0 Cables, some functions will be unavailable and/or their performance reduced. HDM11.4×2, HDM12.O xl DP 1.2 xl Xl (Headphone Socket) 2m Maximum operating distance ooc – 400C 10% 85% Non-condensing 17

****** Page 18 ****** TROUBLESHOOTING PROBLEM No power No picture Buttons on the monitor don’t do anything Noise or other interference SOLUTION Insert the plug securely into the power outlet. Ensure that the equipment is connected properly. Ensure the correct input is selected. Disconnect the power plug and then reconnect it. (The unit may not be operating properly due to lightning, static, or other factors.) Electronic equipment near the unit may be causing interference. Relocate the unit or move the equipment. ENVIRONMENTAL PROTECTION Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres electriQ UK SUPPORT electriQ.co.uk(support If the unit fails to operate call: 0871 620 1057 or complete the online form Office hours: 9AM -1 5PM Monday to Friday eIectriQ.co.uk Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA 18

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELECTRIQ EIQ-32MCV4KAFSHDR (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.