ELEAC AIRX2 (01) PDF Document

The general safety instructions for the ELEAC AIRX2 are:

Please read and follow these safety instructions.

Keep them safe for future reference.

Observe all warnings on the unit and in the manual. Please check the speaker for damage before use.

The unit must be in perfect working condition. Damaged parts may lead to personal injury.

Use the ELEAC AIRX2 only as directed. Connect the unit according to the instructions in the manual.

Install the ELEAC AIRX2 on a level surface only.

When choosing the location for this device do not place them in locations that are:

In direct sunlight

Very humid

Prone to vibrations

Exceptionally hot or cold

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install this device in a closed rack or in a closed cupboard.

Do not put burning candles on or near the device.

Do not install the device near transformers because electromagnetic stray fields can cause hum noise on woofers.

DANGER! Do not open the cabinet because the components and conductors may carry dangerous levels electricity! Servicing to be carried out by qualified service personnel only.

Servicing is required when the loudspeaker has been damaged in any way, such as damage to the power supply cord or the plug, or when liquid has been spilled or objects have fallen into the loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has been dropped. To reduce the risk of electric shock, do not open the loudspeaker. Servicing to be carried out by qualified service personnel only.

Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol, benzene, furniture polish or other agents for cleaning! Modern furniture is often coated with multiple varnishes and plastics which can be treated with chemical agents. Some of these agents contain substances which degrade or soften the rubber feet.

The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner. At end of life do not dispose the speaker with the standard household waste. The speaker must be recycled in accordance with local legislation. Ask your local government for further information on recycling as the device contains valuable raw materials. Disable the speaker before disposal.

This unit is only intended to be connected to voltages that are listed on the rear panel of the cabinet. Connection to any other voltage may cause irreversible damage to the subwoofer and will void the warranty. Use of plug adapters is not recommended because they may allow connection to voltages other than those printed on the back of this subwoofer.

The controls and indicators on the ELEAC AIRX2 Transmitter are:

1. LED/Activity Monitor: This LED is used to show the current status of the AirX2 Transmitter.

2. Power Input: Used for providing power to the unit from the included AC power supply.

3. Audio Input: Used to connect an audio source to the transmitter.

4. SYNC Button: Located on the bottom of the unit is used to pair the transmitter with other AirX2 products. See the section for syncing instructions.

If you are connecting the transmitter to an AV receiver or pre-Amp with a dedicated subwoofer or LFE output, connect a RCA cable (not supplied) from the LFE/Subwoofer output on the AV Receiver/Pre-Amp to the Right RCA input on the subwoofer.

If you are connecting the subwoofer to a pre-amp or receiver without a dedicated LFE/Subwoofer output, connect a set of stereo RCA connectors from pre-outs on the pre-amp to the left and right RCA inputs on the subwoofer. If you are using a pre-amp with only one set of pre-outs, use a splitter for each output on the pre-amp and connect two sets of stereo RCA cables to both the amplifier and to the subwoofer.

When using the AirX2 transmitter with ELAC’s Argo wireless speakers connect the variable audio outputs from you pre-amp/source. PLEASE NOTE THAT THE TRANSMITTER DOES NOT CONTROL VOLUME! A FIXED LEVEL SOURCE WILL OUTPUT AT FULL VOLUME!

Please follow the pairing process to wirelessly connect the Argo speakers to the transmitter.

Pairing the wireless transmitter with other AirX2 products is very simple. Please follow the below steps to complete the process.

1. Press and hold the Wireless Pair button on the AirX2 compatible subwoofer or speakers until the LED begins to flash rapidly (Around 2 times per second).

2. Press and hold the Wireless Pair button on the bottom of the transmitter until the wireless pair LED on the subwoofer or Argo Speakers stops flashing and goes off (No LED means the speaker is wirelessly paired.)

3. Repeat with additional speakers/subwoofers (Up to 3 units)