Click here to download ELATION PROFESSIONAL PROTRON COLOR (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Protron ColorTM Introduction PROFESSIONAL User Instructions oElation Professional@ 4295 Charter Street Los Angeles Ca. 90058 elationlighting.com Unpacking: Thank you for purchasing the Protron Color TM by Ela- tion Professional@. Every Protron Color TM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during ship- ping. If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact. In the event damage has been found or parts are missing, please contact our customer support number for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below. Introduction: To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. The Protron Color TM is a 750 watt strobe, with a color wheel for colorful strobing. Up to 16 units may be linked together and controlled by single controller. The units’ intensity, flash rate, and flash duration can be manually adjusted using the dip- switches. For remote control operation an optional remote control is available from Elation Professional@. Customer Support: Elation Professional@ provides a customer sup- port line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at elationlighting.com for any com- ments or suggestions. For service related issue please contact Elation Professional@. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. Voice: Fax: E-mail: (323) 582-3322 (323) 582-3108 support@elationlighting.com 3/04 Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle when ever possible. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 2

****** Page 2 ****** Protron ColorTM Features Protron ColorTM Safety Warnings Bright 750 Watt Lamp Adjustable Flash Rate, Intenstiy Rate, and Flash Duration Colorful Strobing Large coverage area Thermostat Protection Easy lamp Replacement Link Up To 16 Units Together Built-ln Adjustable Hanging Yoke Protron Color TM Warranty Registration The Protron Color TM carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. num- ber must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. num- ber by contacting customer support at (323) 582-3322. Protron Color TM Cleaning Instructions Due to fog residue, smoke, and dust cleaning the fixture should be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the out- side casing every 20 days. 2. Use normal glass cleaner with a soft cloth to wipe down the inside reflector and lens every 30-60 days. 3. Always be sure to dry all parts completely before plugging the unit back in. 4. Frequent cleaning the unit will extend lamp life and ensure the fix- tures reliability. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy use we rec- ommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 3 Safety Issues: This unit may blow a fuse if the maximum allotted load of 20 amps (10 amps 220v version) is reached. If the fuse needs replacement, always replace the fuse with same exact type that was remove, unless otherwise instructed by an authorized Elation Profes- sional@ service technician. Use ofa different type fuse from that which is recommended may cause fire or electric shock and will void the manufactures warranty. • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture. • Do not spill water or other liquids into or on to your unit. • Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to oper- ate this unit if the power cord has been frayed or broken. • Disconnect from main power before making any type of connection. • Do not remove the cover under any conditions. There are no user serviceable parts inside. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6″ (15cm) between this device and a wall. • Do not attempt to operate this unit, if it becomes damaged. • This unit is intended for indoor use only, use of this product out- doors voids all warranties. • During long periods of non-use, disconnect the unit’s main power. • Always mount this unit in safe and stable matter. • Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 3 for cleaning details. • Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the unit. C. The unit has been exposed to rain or water. D. The unit does not appear to operate normally or exhibits a marked change in performance. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 4

****** Page 3 ****** Protron ColorTM DMX Set Up Protron ColorTM sound activation. DMX Set Up Power Supply: Before plugging your unit in, be sure the source volt- age in your area matches the required voltage for your Elation@ Pro- tron Color. TM The Elationo Protron Color TM is 120v only. Because line voltage may vary from venue to venue, you should be sure your unit voltages matches the wall outlet voltage before attempting to operate you fixture. DMX-512: DMX is short for Digital Multiplex. This is a universal pro- tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that trav- els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter- minals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a sin- gle controller, as long as all fixtures and the controller are DMX com- pliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Dipswitches in DMX mode: This unit uses dipswitches to assign a DMX address. Each dipswitch represents a binary value. Dipswitch 1 address equals 1 Assigning DMX Address: Each dipswitch has a preset value. A spe- cific DMX address is set by combining the dipswitches that sum your desired value. For example: To achieve a DMX address of 7, combine dipswitches 1, 2, and 3. Since dipswitch 1 has a value of 1, dipswitch 2 has a value of 2, and dipswitch 3 has a value of 4, the combination of the three create a DMX value of 7. (See example below). Set DMX address 1: Dip-switches # 1 Set DMX address 7: Dip-switches # 1 Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The Protron Color TM can be controlled via DMX-512 protocol. The Protron ColorTM is a five channel DMX unit. The DMX address is set on the side panel of the Protron Color TM Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output (Figure 1). If you are making your own cables, be sure to use standard two con- Figure 1 Dipswitch Dipswitch Dipswitch Dipswitch Dipswitch Dipswitch Dipswitch Dipswitch Dipswitch 2 address equals 2 3 address equals 4 4 address equals 8 5 address equals 16 6 address equals 32 7 address equals 64 8 address equals 128 9 address equals 256 10 – Some units omit dipswitch 10. When a unit does ductor shielded cable (This cable may be purchased at almost all pro sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and can not be split. Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not con- nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. COMMON DMX + DMX – OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 6 DMX512 OUT 3-PIN XLR 02 DMX5i2 IN 3-PIN XLR Figure 2 include dipswitch #10, it is usually used for special functions such as OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 5

****** Page 4 ****** Protron ColorTM XLR Male Socket 1 Ground 3 Hot Figure 3 DMX Set Up XLR Pin Configuration Protron ColorTM Operating Instructions XLR Female Socket 1 Ground 3 Hot Pin I Pin 2 Pin 3 — Ground = Data Compliment (negative) — Data True (positive) Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con- nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR socket of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behav- ior. 01 3 2 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 DMX-) Figure 4 and PIN 3 (DMX +) of the last ixture. 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion Power Supply: This unit is available only in 120v. Before plugging your unit in be sure the source voltage in your area matches the required voltage for your Elationo Protron Color. TM General Operation: This fixture is designed to operate as a stand alone unit, or in a Master/Slave configuration. It can also operate via DMX controller. The Protron Color TM is ready to be plugged in out of the box. Duty Cycle: Because the Protron Color TM can be used for continuous output (ie while simulating lightning), it can build up intense heat. Due to the build up of intense heat the unit should not run for 15 minutes contin- uously. After 15 minutes of continuous use, allow the unit to cool for about fifteen minutes, this will greatly increase the lamp life and insure product longevity. Operating Modes: Stand Alone: In stand alone the unit will function as a normal strobe light. Rate (speed), Intensity (brightness), and duration (length between flashes) are set directly on the unit. Note that these settings are made using the dipswitches on the back of the unit. Once the settings are made they can only be changed by physically adjusting the dipswitches on the unit. Be aware of this if you plan on installing your strobe in a per- manent application, if your are not satisfied with your settings you will have to physically remove the unit and adjust the dipswitches. Please see the dipswitch traits below. “Flip” the dipswitches to the “on” pos- tion to activate. Dipswitch Traits (Manual Mode): Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used 3-Pin XLR Female (Out) 5-Pin XLR Male (In) Pin I Pin 2 Pin 3 Pin 4 – Pin 5 – Pin I Pin 2 Pin 3 Do Not Use Do Not Use 1. 2. 3. 4. Dipswitches 1-3 control the speed of the strobe. Dipswitch #1 being the slowest strobe, and dipswitch #3 being the fastest strobe. Dipswitches 4-6 control the brightness of the strobe. Dipswitch #4 being the dimmest, dipswitch #6 being the brightest. If you want the strobe to be set to one color only (no rotation), leave dipswitch #9 in the off postion, and follow the small chart on page 9. If you want the strobe to color change, “flip” dipswitch #9 to the OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 7 OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 8

****** Page 5 ****** 5. Protron ColorTM 0-15 16-31 32 – 47 48 – 63 64 – 79 80 – 95 96-111 112- 127 128 – 144 145 – 159 160 – 175 176 – 191 192 – 207 208 – 255 Operating Instructions “on” postion. Dipswitch #7 will control the speed of the rotating gel wheel. If dipswitch #7 is in the “on” postion, the gel wheel will be on high speed, if the dipswitch #7 is in the “off” postion the wheel will be on low speed. If you “flip” dipswitch #8 to the “on” postion the gel wheel will rotate counter-clockwise. If you leave dipswitch #8 in the “off” postion the gel wheel will rotate clockwise. Protron ColorTM COLOR WHITE DIPSWITCH OFF DIPSWITCH OFF RED YELLOW BLUE ON OFF OFF ON ON ON Universal DMX Control: This mode allows you to use a universal DMX-512 controller such as the Elationo DMX Operator TM or Show Designer. TM 1. 2. 3. 4. 5. To control your fixture in DMX mode, follow the set-up procedures on pages 5-7 as well as the set-up procedures included with your DMX controller. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. Assign your desired address to the unit, and “flip” dipswitch #10 to the “on” postion. The Protron ColorTM uses five DMX channels. Use your DMX con- troller to activate the various built-in patterns. See page 11 for a list of DMX traits. For help operating in DMX mode consult the manual included with your DMX controller. NOTE: If running in Master/Slave address configuration while using a DMX controller, follow the DMX address setttings on page 14. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 10 Channel 1 2 3 4 5 Value o – 255 o – 255 o – 255 o – 255 o – 255 DMX Traits Function FLASH SPEED SLOW —-— FAST FLASH DIMMER BLACKOUT FULL INTENSITY FLASH DURATION 0-16 COLOR WHITE WHITE + RED RED RED + YELLOW YELLOW YELLOW + BLUE BLUE BLUE + WHITE NO FUNCTION COUNTER-CLOCKWISE ROTATION OF THE GEL WHEEL NO FUNCTION CLOCKWISE ROTATION OF THE GEL WHEEL NO FUNCTION INTERNAL PROGRAM GEL WHEEL ROTATION SPEED SLOW ………….-..> FAST OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 1 1

****** Page 6 ****** Protron ColorTM Lamp Replacement Protron ColorTM (diagram 1). Lamp Replacement Halogen Lamp Warning! This fixture is fitted with halogen lamps which are highly susceptible to dam- age if improperly handled. Never touch the lamps with your bare fingers as the oil from your hands will shorten lamp life. Also, never move the fixture until the lamps have had ample time to cool. Remember, lamps are not covered under warranty conditions. Warning! Allow the lamp to discharge all current. Allow the unit 24hrs. to discharge before changeing the lamp. Stored current can cause a very severe shock. Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized Elation Professional@ technician. Replace with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If after you have replaced the lamp or fuse and you contin- ue to blow either one, STOP using the unit. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage. Fuse Replacement: Disconnect the unit’s main power supply. Insert a standard flat head screw driver in to the fuse holder hous- ing (located on the rear of the unit). Turn the screwdriver in a coun- ter-clockwise direction to remove the fuse holder. Remove the old fuse and discard it, replace the fuse with the same type. Insert the fuse holder back into it’s housing and turn in a clockwise direction to secure the holder in place. Lamp Replacement: Caution! Never open the unit when in use. Always disconnect the main power and allow the fixture ample time to cool before attempting to replace the lamp. Lamp replacement has been made simple by incorporating a remove tray that is retained by a single thumb screws. Again, please remember to always replace with the exact same type lamp. 1. Be sure to follow the proper procedures when handling halogen lamps. Never touch the new lamp with your bare fingers. 2. Unscrew the two thumb screws located on the glass cover in the top corners of the unit. 3. Loosen the small phillips screw located to the right of the reflector OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 12 4. 5. 3. 4. 4. 5. Gently rotate the reflector by hand so that the back of the reflec- tor is now in the front (diagram 2 & 3). Located at the back of the reflector is a white ceramic wire con- nection block (diagram 4). The ceramic block has six wires connected to it, three on each side. The three wires on the left side are the lamp wires, they are secured by a flat head screw. NOTICE: When you disconnect the lamp wires to replace the lamp, you will have to remember which wire went where. They must be reconnected the same way. Replace the lamp with an exact match. Connect the three wires to the ceramic block as they were when you disconnected them. Reassemble in reverse order. Diagram 1 Diagram 3 Diagram 2 Dia ram 4 OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 13

****** Page 7 ****** Protron ColorTM DMX Address Chart This chart list the DMX dipswitch setting for DMX address 1 through 511. Follow the instructions below to configure fixture dipswitches with your desired DMX address. DMX Address Quick Reference Chart 160 „192 224 256, 320. 352,384, 97 -129 • 449 481 34 66 162 ‘194. 226. 258. 290 L 322″ 354 259 291 452, 484 229 261 263″ 295 327 359 391’ 423 455 487 264, 328 360 169 201 329 361 330 362 395 427 269 301 239 271 176 208 336 368 400 432 209 241 369 401 274 306 179 211 339 371 403 435 276 308 340 372 117 .149 181 -213 118 •150 182 •214 184 .216 249 281, 313, 377 •409, 185 •217 442 ,474, 187 „219 283, 315, 347, 319 443 .475 444 .476 61 93 125.157. 190 „222 414. 446. 447 .479 191 •223 Protron ColorTM 2-YEAR LIMITED WARRANTY Warranty DIP SWITCHES DMX DIP Switch Settings X = OFF Dip Switch Position 39 36 x x x x 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 x x 3 33 ‘ 35 36 37 38 39 41 42 43 44 45 46 47 48 49 50 51 52 53 54 56 57 59 60 62 63 x O x 128 131 132 133 71 • 103 135 167 ‘199 40 • 72 • 104 ‘136’ 168 232 137 138 139 140 141 142 143 144 145 146 147 148 55 87 183 247 x O o x 193 195 196 197 198 202 203 204 205 206 201 210 180 212 244 58 90 122 186 ‘218 250′ 282′ 314. 346. 378 x x x x o 64 96 65 67 68 100 69 101 70 • 102 134 13 105 74 106 75 107 16 108 77 109 78 110 19 111 80 112 81 113 82 114 83 115 84 116 85 86 88 • 120 152 89 • 121 153 91 123-155 92 • 124 156 94 • 126 158 95 • 127 159 x o x o 161 163 164 165 166 170 171 172 173 174 175 177 178 x o o o 227 231 233 234 235 237 242 243 251 O x o o x o x o x o x o x o x o x o x o x o x o x o x o x o x o x o x o x x o o X x o O x x o x X o o X x o x x O o x X o o X x o O x x x x o o o o x x x X o o O o x x x x o o o o x X X x O O o O x x x x x x x x o o o o o o o o x x x x x x x x o o o o o o o o x x x x x x x x x x x x x x x x o o o o o o o o o o o o o o o o X 225 257. 353-385. 417 323 324 325 331 332 333 334 335 337 338 246, 278 310, 342, 374,406, 438 279. 311 343 375.407. 344 228 260 292 265 266 267 236 268 300 238 270 302 240 272 304 273 275 293 230, 262, 294 326. 358 297 298 299 303 305 307 245. 277. 309, 341. 313, o x o 355 356 357 363 364 365 366 361 310 316, 248 280 312, 188 „220 252 284, 348, 380 253 285 317 349. 381 254 286, 318, 350, 382, 255 287, 319, 351, 383 O o x X 387 388 389 390 392 393 394 396 397 398 399 402 404 405 408 410 411 412 413 415 o o x o 416 • 418 419 420 421 422 424 425 426 428 429 430 431 433 434 436 431 • 439 440 441 445 O o X 448 450 453 454 456 451 458 459 460 462 463 464 465 466 467 468 469 470 471 472 473 477 478 O o O 480 482 483 485 486 488 489 , 490 491 492 , 493 494 495 496 497 498 , 499 500 501 502 503 504 505 506 501 508 509 510 511 DMX Address The center numbers of this chart (1-511) represent a DMX address. The and “01’ ‘s along the top and side of the chart represent dip switch poistion (‘IXI’ for off and for on). Find your desired DMX address from the center chart. Identify the position for dip switches 1-5 from the chart on the left and dip switches 6-9 from the chart on the top. Adjust the dip switches on your fixture to match the position settings of the chart. For fixtures with 10 dip switches; dip switch 10 is reserved for special functions. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 14 A. Elation Professional@ hereby warrants, to the original purchaser, Elation Professional@ products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the prod- uct is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the Elation Professional@ factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional@ will pay return ship- ping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional@ shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professional@ concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional@factory unless prior written authorization was issued to purchaser by Elation Professional@; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, Elation Professional@ will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional@ under this warranty shall be limited to the repair of the product, or replace- ment thereof, including parts, at the sole discretion of Elation Professional@. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect. E. Elation Professional@ reserves the right to make changes in design and/or improve- ments upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any acces- sory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional@ in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warran- ties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional@ be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to Elation Professional@ Products and supersedes all prior warranties and written descriptions of warranty terms and condi- tions heretofore published. OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 15

****** Page 8 ****** Protron ColorTM Model: Protron Voltage*: Lamp: Fuse: Dimensions: Weight: Colors: Duty Cycle: Ventilation: Warranty: Specifications C 010 r TM 120v-60Hz ZB-300 750 Strobe lamp 20A 250v 10″ (L) x 22″ (W) x 9.6″ (H) 24 Lbs. 3 Plus White 15 minutes on/off Fan Cooled 2 Year (730 Days) *Voltage is preset at the factory and can not be changed by the user. Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. oElation Professional@ Elation World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-3322 / Fax: 323-582-3108 Web: elationlighting.com / E-mail: info@elationlighting.com OEIation Professional@ – elationlighting.com – Protron Color TM Instruction Manual Page 16

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELATION PROFESSIONAL PROTRON COLOR (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.