ECHOMASTER PRO RVC-W3 (01) PDF Document

The features of the ECHOMASTER PRO RVC-W3 include:

• Universal wireless camera and receiver

• CVBS/AHD Selectable

• Receiver supports 2 wireless cameras (Compatible camera: P/N: RVC-W3-C)

• 3 viewing modes: CAM1, CAM2 or split screen

• Infrared night vision

The Box Contents for the ECHOMASTER PRO RVC-W3 are:

• Camera (with built in TX)

• Camera Power Cable

• Power & Video Cable (Length 0.15m/0.5ft)

• Receiver Extension Cable (Length 3.66m/12ft)

• 2 x Red Male Spades

• 3 x Antennas

• Hole Saw

• Receiver (RX)

• 2 x Red T-taps

• 2 x 10mm screws

• 3 x Cable Ties

• Double Sided Tape

• User Manual

The Camera & Receiver have been paired previously, so there is no need to pair again in normal use cases. Pairing is needed if the camera or receiver needs to be replaced or under other special circumstances.

To pair the ECHOMASTER PRO RVC-W3:

1. Power on the RX (Receiver). Press and hold the button on the RX for 3 seconds. It will enter pairing mode and the LED indicator will begin to flash rapidly.

2. Within 30 seconds, power on the Camera. Pairing will then start. If the signal is not detected within 30 seconds, pairing mode will end. Repeat the steps for pairing.

3. Once pairing is complete, the indicator light on the RX will change from flashing rapidly to constant ON.

The original camera is paired to CAM1 by default. To pair an additional compatible camera (P/N: RVC-W3-C) to your ECHOMASTER PRO RVC-W3:

1. Press the RX Button to switch to CAM2.

2. Repeat the standard pairing steps: Press and hold the RX button for 3 seconds until the LED flashes rapidly, then power on the new camera within 30 seconds.

To cycle through video sources on the ECHOMASTER PRO RVC-W3, press the RX Button to switch between CAM1, CAM2, or split screen mode. Note that the RX must be in an accessible location to use this feature.

The default factory setting for the ECHOMASTER PRO RVC-W3 is AHD. To switch between AHD and CVBS mode, press and hold the RX Button for 6 seconds. The indicator light will flash slowly 3 times to indicate a successful selection.

To check the firmware (FW) versions on your ECHOMASTER PRO RVC-W3, press the RX Button three times consecutively. Both the RX and TX FW versions will appear on the screen. The TX FW will only appear if a camera is connected.

Follow these instructions for wiring the ECHOMASTER PRO RVC-W3:

Camera wiring:

• Red (Power): Locate the Parking Lamp (+) wire in the vehicle/trailer. Connect this wire to the camera’s red power cable.

• Black (Ground): Locate a suitable location to ground (negative) the black wire in the wiring harness. You may connect this wire to a factory ground point in the vehicle or attach a ring terminal to the black wire and screw it into the body of the vehicle/trailer. If you screw into the body, clean the area of any paint or adhesives to allow for good metal-to-metal contact.

Receiver wiring:

• GND (Ground): Connect to a factory ground point in the vehicle. Only one of the GND leads from the receiver needs to be connected; two are provided for convenience.

• ACC: Connect to an accessory power source.

NOTE: If using with an EchoMaster monitor, connect the receiver’s GND wire directly to the factory GND. Do not connect to the GND from the monitor adapter harness.

If the ECHOMASTER PRO RVC-W3 causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.