ECHO DSRM-2600 (01) PDF Document

Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control.

Push power button (A) once to turn on power to unit. Power indicator LED (B) illuminates when power to unit is turned on.

Hold down trigger switch lockout (C) and depress trigger switch (D) to increase RPM to operating speed.

To increase operating speed, press + (E). To decrease operating speed, press – (F). Press and hold + button for one second to maintain consistent speed. Press + again to cancel.

Release trigger switch and trigger switch lockout, and allow trimmer head to stop.

Push power button (A) to turn off power to unit. Power indicator LED (B) turns off when power to unit is turned off.

If the trimmer head does not stop when the trigger and trigger lockout are released, push power button to turn off and remove the battery to stop the power supply to product. Have your authorized servicing dealer repair power button before using product again.

Feed the spinning line into the material to be cut. Tilt the line head to one side to direct cutting debris away from you:

Model SRM/DSRM/PAS/SB/TX/C/T (Straight shaft, counter-clockwise line head rotation) – Tilt the cutting head down on the right side (muffler side) while cutting to direct cutting debris away from operator. Feed the line gradually into the material you wish to cut, avoiding contact with fences or other barriers.

GT models: Tilt cutting head to the left while cutting to direct debris away from the operator.

To cut large sections of field grass and weeds swing the cutting head in a level arc, gradually feeding the blade into the material being cut. Adjust throttle speed according to your work.

Do not swing the main pipe with arms. Turn hips to swing the blade horizontally from right to left, and cut weeds on the left side of the blade.

Do not scythe back and forth as the grass may scatter and kickback may occur easily.

Tilt blade left by 5 to 10 degrees so that cut grasses will push left, making progress easier.

Move forward with each arc to cut a swath.

Scything – Swing the cutting head in a level arc, gradually feeding the line into the material being cut. Move forward with each arc to cut a swath. Width of cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller arc for a narrow swath. Keep line head tilted to direct cutting debris forward or away from you.

Edging and Scalping – Both of these are done with the nylon line cutting head tilted at a steep angle. Scalping is removing top growth, leaving the earth bare. Edging is trimming the grass back where it has spread over a pavement or driveway. During both edging and scalping, hold the unit at a steep angle in a position where the debris, and any dislodged dirt and stone, will not come back towards you even if it ricochets off the hard surface.

Debris flows in direction of line head rotation. Change line head position to assure debris flow is directed away from operator.

Keep cutting line away from wire fences to avoid entanglement.

Operate trimmer only with cutting head below knee height.

3-Tooth Grass/Weed Blades may be used wherever the nylon line head is used. DO NOT use this blade for heavy weeds or brush.

8-Tooth Weed/Grass Blade is designed for grass, garden debris and thick weeds up to 19 mm (0.75 in.) diameter. DO NOT use this blade for brush or heavy woody growth.

80-Tooth Brush Blade is designed for cutting brush and woody growth up to 13 mm (0.5 in.) diameter.

22-Tooth Clearing Blade is designed for dense thickets and saplings up to 64 mm (2.5 in.) diameter.

Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut. Following proper cutting techniques will prevent blade thrust.

Blade thrust can be violent enough to cause the unit and/or operator to be propelled in any direction, and possibly lose control of the unit.

Blade thrust can occur without warning if the blade snags, stalls or binds.

Blade thrust is more likely to occur in areas where it is difficult to see the material being cut.

Using the correct blade for the cutting job

Using properly sharpened blades

Applying consistent, even force to the blade during the cut

Avoiding obstacles and ground hazards

Using extra care when cutting harder materials such as extremely dry brush, saplings, and small trees

Cutting from a stable, secure position

To free a blade that is bound in the cut, stop the unit, and support the trimmer or brushcutter to keep stress off the blade. Push the tree away from the entry point of the cut to open the cut, and pull the blade directly away from the cut in a straight-line motion. Use caution when releasing the tree to avoid being struck by spring-back or falling.

Keep blades sharp

Avoid excessive pressure during cuts

Don’t exceed cutting capacity of blade

Don’t use blades with damaged or missing cutting teeth

Don’t rock blades in cut

The table below outlines the daily or before use maintenance procedures and skill levels for the ECHO DSRM-2600:

MAINTENANCE PROCEDURE NOTES:

1 Apply lithium based grease every 25 hours of use.

2 Apply lithium based grease every 50 hours of use.

Release trigger switch and trigger switch lockout and allow trimmer head to stop.

Make sure power indicator LED is not illuminated.

Depress battery latch release (A) and slide battery out of power head.

Use compressed air or a soft bristle brush to remove debris from battery and battery compartment.

Inspect cut-off knife (B) for damage or wear.

Assure that it is properly attached to debris shield.

Clean all loose debris from gear case.

Remove plug (A) and check level of grease.

Add grease if necessary. DO NOT over-fill.

Loosen handle clamping screw (B) and slide throttle handle forward.

Loosen clamping screw (C) and slide shaft out of power head.

Pull flex cable (D) out of shaft housing, wipe clean and re-coat with 15 ml (0.5 oz.) grease.

Slide flex cable (D) back into shaft housing. DO NOT get dirt on flex cable.

Reassemble in reverse order.

Cut one piece of line to recommended length. 2.0 mm (0.080 in.) diameter 6 m (20 ft.). 2.4 mm (0.095 in.) diameter 6 m (20 ft.).

Align arrows on top of knob with openings in eyelets.

Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head.

Hold trimmer head while turning knob clockwise to wind line onto spool until about 13 cm (5 in.) of each line remains exposed. Trimmer head is now fully loaded and ready for operation.

If the plug is not connected to power outlet: Plug in the charger.

If the battery is not installed properly: Check the battery installation.

If there is an obstructed connection: Reinstall battery again after removing obstructions from connection.

If there is a fault in the charger: Consult your dealer.

If the battery is not installed properly: Check the battery installation.

If there is a fault in the battery: Consult your dealer.

If the battery is discharged: Charge the battery.

If the battery is outside acceptable temperature range: Remove the battery and allow to cool.

If the battery is outside acceptable temperature range: Remove the battery and allow to cool.

If unit electronics are too hot: Turn unit off and allow to cool.

If the battery is discharged: Charge the battery.

If there is not enough line on the spool: Refill with new line.

If line is tangled in the spool: Untangle and refill line.

If the cut off knife is damaged or missing: Consult your dealer.

Make sure power to unit is turned off.

Align ridges (A) on battery with grooves in power head. Slide battery into power head.

Assure the battery latch (B) snaps into place and battery is secure before beginning operation.

To remove battery, depress battery latch release (C) slide battery out of power head.

Loosen harness clamp screw.

Put on harness and attach unit to harness.

Slide harness clamp up (A) or down until unit balances with head approximately 50-75 mm (2-3 in.) from the ground.

Tighten harness clamp screw.

Loosen U-Handle clamp screws (B), and position U-Handle for comfortable operation.

Tighten U-Handle clamp screws securely.

Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Wear snug-fitting, durable clothing:

Pants should have long legs, shirts should have long sleeves.

DO NOT WEAR SHORTS.

DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth.

Keep clothing buttoned or zipped, and keep shirt tails tucked in.

Wear sturdy work shoes with nonskid rubber soles.

DO NOT WEAR OPEN TOED SHOES.

DO NOT OPERATE UNIT WITH BARE FEET.

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces to not allow for safe handling and control of the tool in unexpected situations.

Recharge only with ECHO eFORCE™ 56V battery series chargers. A charger that is suitable for one type of battery may create a risk of fire when used with another battery.

Use only with ECHO eFORCE™ 56V battery series. Use of any other battery may create a risk of injury and fire.

When battery is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Do not open or destroy the battery. Electrolytes contained within the battery are corrosive and may cause damage to eyes or skin if released. It may be toxic if swallowed.

Exercise care in handling batteries to avoid shorting the battery with conducting materials such as rings, bracelets, keys, etc. The battery or conductor may overheat and cause burns if contact with said materials is made.

Do not use a battery or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

Do not expose a battery or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C (266°F) may cause explosion.

Follow all charging instructions and do not charge the battery or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Do not cover the charger. Covering the charger will prevent it from cooling.

Do not operate the charger in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Charger can produce sparks which may ignite the dust or fumes – there is a risk of explosion.

Connect the charger only to the mains of voltage and frequency specified on the rating plate.

Connect the charger only to an easily accessible wall outlet.

Never insert objects in the battery’s or charger’s cooling slots.

Do not charge or use a defective, damaged or deformed battery and charger.

Do not open, damage or drop the battery or the charger.

Fluid may leak from the battery if it is damaged or not used properly; avoid contact with the skin. In the event of accidental contact, wash the affected areas of the skin with plenty of water and soap. If fluid gets in the eyes, do not rub. Rinse the eyes with plenty of water for at least 15 minutes. Also seek medical assistance.

Never bridge (short circuit) the battery contacts or the charger’s terminals with metallic objects.

Protect from direct sunlight, heat and open flames and never throw battery into fire; there is a risk of explosion.

In the event of smoke or fire in the charger, disconnect it from the wall outlet immediately.

If the connecting cord is damaged, immediately disconnect the plug from the power supply to avoid the risk of electric shock.

Do not expose battery to microwaves or high pressure.

To reduce the risk of stumbling, position and mark the connecting cord in such a way that it cannot be damaged or endanger others.

Turn power to unit off.

Remove battery.

Remove accumulation of dirt and debris from exterior of unit.

Tighten all screws and nuts.

Cover battery compartment, battery and charger.

Store unit in a dry, dust-free place out of the reach of children.

Remove battery from charger.

Store in a dry, dust-free place, out of the reach of children.

Store in temperatures between -20°C (-4°F) and 60°C (140°F).

If battery is stored for longer than six months, charge it to 100% capacity.

Remove battery from charger.

Disconnect charger from power supply.

Store in a dry, dust-free place, out of the reach of children.

Level 1 = Easy to do. Common tools may be required.

Level 2 = Moderate difficulty. Some specialized tools may be required.

Level 3 = See your dealer.