ECHELON GT+ (GTPLUS) (01) PDF Document

The manufacturer recommends placing the equipment in a space where you have two feet of clearance on all sides for safe mounting and dismounting. The minimum dimensions are 0.5 meters (19.7 inches) on at least one side, and 0.5 meters (19.7 inches) either behind or in front of the exercise bike.

While cleaning the equipment, please use a soft rag with mild detergent or water to wipe down the machine. Do not use corrosive chemical liquids which may damage the cover. It is recommended to wipe down the equipment after each use to keep it sanitary.

To disconnect, turn all controls to the off position, then remove the plug from the outlet. To properly move the bike, carefully tilt it forward to engage the transportation wheels located on the front foot. Use these wheels to move the bike to the proper location when not in use.

Always use the equipment on solid, level ground and in a well lit and ventilated area.

Always check that the seat and handlebars are securely fastened before use.

Never allow children to play on or around the bike to protect them from injury from moving parts.

The weight limit for this bike is 300 lbs (136 kg). Do not use the equipment if your body weight is in excess of 300 lbs (136 kg).

Always wear proper attire and footwear that fully covers your feet. Long hair should be tied back and shoelaces should be tucked into your shoes.

Always wait until the pedals have come to a complete stop before taking your feet off of the pedals or dismounting.

Never use the equipment in a standing position at high revolutions per minute (RPM).

Always keep your pelvis positioned over the center line of the bike.

Never adjust the resistance of the flywheel or the position of the handlebars while in a standing position.

The following items are included:

1. ECHELON GT+ (GTPLUS) Main Frame

2. Handlebars

3. Front foot

4. Rear foot

5. Tablet mount

6. Handlebar post

7. Seat post

8. Dumbbell holder

9. Pedals

10. Tablet mount bolts and washers

11. Foot bolts (x4)

12. Dumbbell holder bolts (x2) and Water bottle holder bolts (x2)

13. Handlebar adjustment knob washer

14. Handlebar adjustment knob

15. Wrench

16. Double-sided wrench

17. Hex key

18. Power adapter

19. Power cord

20. Seat

21. Water bottle holder

1. Lay the bike on its side and remove the wheel chock bolts using the hex key.

2. Pull the wheel chock out using your wrench or fingers and set aside the wheel chock and bolts.

3. Place the rear foot under the rear bracket.

4. Insert the foot bolts into the rear foot and tighten down with the hex key.

5. Place the front foot under the front bracket.

6. Insert the foot bolts into the front foot and tighten down with the hex key.

1. Unscrew the seat height adjustment knob but do not remove it, then pull the knob out.

2. Fully insert the seat post into the frame, release the knob, and ensure the post is secure.

3. Place the seat onto the seat post and adjust it to the correct position.

4. Secure the seat using the included wrench on both sides.

5. Place the dumbbell holder onto the seat post.

6. Finger tighten the bolts, then tighten them fully with the hex key.

1. Unscrew the handlebar post adjustment knob but do not remove it.

2. Connect the wire from the frame to the wire from the handlebar post.

3. Pull the knob out and fully insert the handlebar post into the frame. Release the knob to secure it.

4. Untie the twist tie from the tablet mount and pull out the connect wire from the handlebar post.

5. Connect the wire from the handlebar post to the wire at the bottom of the tablet mount and remove the twist tie.

6. Feed excess wire into the handlebar post and slide the tablet mount into the handlebar post.

7. Place flat washers onto the bolts and finger tighten the tablet mount bolts, then secure them with the hex key.

8. Place the washer onto the handlebar adjustment knob and place the handlebar on the handlebar post.

9. Secure the handlebar using the handlebar adjustment knob and washer.

1. Assemble the water bottle holder and slide it onto the post. Finger tighten the bolts and secure them with the hex key.

2. For the right pedal, match the pedal and crank arm marked with the “R” label. Remove the nut from the right pedal by turning counterclockwise. Screw the right pedal onto the right crank arm clockwise. Use the double-sided wrench to ensure the pedal is firmly seated. Finger tighten the nut clockwise back onto the pedal bolt and use the single-sided wrench to tighten it clockwise while holding the pedal with the double-sided wrench.

3. For the left pedal, match the pedal and crank arm marked with the “L” label. Note that the threads are reversed on the left pedal. Remove the nut from the left pedal by turning clockwise. Screw the left pedal onto the left crank arm counterclockwise. Use the double-sided wrench to ensure it is firmly seated. Finger tighten the nut counterclockwise back onto the pedal bolt and use the single-sided wrench to tighten it counterclockwise while holding the pedal with the double-sided wrench.

1. Loosen the resistance knob by turning it counterclockwise.

2. Remove the insert from the flywheel cover.

3. Connect the power adapter segments together.

4. Plug the power adapter into the port located on the rear foot bracket.

If your bike does not connect, follow these steps on your tablet device:

Step 1. Navigate to the Settings app and select Apps (or Application/Application manager on older Android versions).

Step 2. Select the icon in the top right (or “MORE” on older versions) and select “Show system” or “Show system apps”.

Step 3. Select “Bluetooth Share”, then “Storage”, and select either “Clear Data” or “Clear Cache”.

Step 4. Restart the Echelon Fit app and attempt to connect again.

Slide Adjustment (Fore/Aft): Turn the seat slide adjustment knob counterclockwise to loosen. Move the seat along the track to your desired location (levels 1 to 7). Turn the knob clockwise to secure it in place.

Height Adjustment: Turn the seat height adjustment knob counterclockwise until you can pull it out halfway. Pull and hold the knob while raising or lowering the seat to the desired location (levels 1 to 17). Ensure the knob engages with one of the adjustment holes, then turn it clockwise until secure.

Height Adjustment: Turn the handlebar height adjustment knob counterclockwise until you can pull it out halfway. Pull and hold the knob while raising or lowering the handlebars (levels 1 to 9). Ensure the knob engages an adjustment hole and turn it clockwise until secure.

Fore/Aft Adjustment: Loosen the handlebar knob. Move the handlebar to the desired location (levels 1 to 7). Tighten the adjustment knob until secure.

To adjust the resistance while riding, turn the resistance adjustment knob to the left or right. To stop the bike immediately, press down on the resistance adjustment knob.

The equipment must be grounded. If it malfunctions or breaks down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not use an extension cord or ungrounded outlet. Ensure the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.