DW MEGAPIX DWC-MB72WI4TWDMP (01) PDF Document

The following items are included with your DW MEGAPIX DWC-MB72WI4TWDMP camera:

• Quick Setup and Download Guides – 1 set

• Screws and Plastic Anchors – 4pcs – 1 set

• Mounting Template – 1

• Star Wrench (T-20) – 1

• Waterproof Cap and Rubber Rings (Black: ø0.15″ (ø4mm), White: ø0.19″ (ø5mm)) – 1 set

To avoid serious injury or death, please adhere to the following warnings:

1. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. When the product is mounted on a wall or ceiling, the device shall be firmly fixed.

2. Be sure to use only the standard adapter specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

3. Make sure the power supply voltage is correct before using the camera.

4. Incorrectly connecting the power supply or replacing the battery may cause an explosion, fire, electric shock, or damage to the product.

5. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause excessive heat generation or fire.

6. Securely plug the power cord into the power source. An insecure connection may cause a fire.

7. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.

8. Do not install in a location subject to elevated temperature, low temperature, or high humidity. Doing so may cause fire or electric shock.

9. Do not place conductive objects (e.g. screwdrivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

10. Do not install in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

11. Do not install near any heat sources such as radiators, heat registers, or other products (including amplifiers) that produce heat.

12. Keep out of direct sunlight and heat radiation sources. It may cause a fire.

13. If any unusual smells or smoke come from the unit, stop using the product at once. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

14. If this product does not operate normally, contact the nearest service center. Never disassemble or change this product in any way.

15. When cleaning the product, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

To avoid injury or equipment damage, please follow these cautions:

1. Use proper safety gear when installing and wiring the product.

2. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibration or magnetic interference.

3. Do not use this product near water.

4. The product shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product.

5. Avoid aiming the camera directly towards extremely bright objects such as the sun, as this may damage the image sensor.

6. The Main plug is used as a disconnect device and shall stay readily operable at any time.

7. Remove the power adapter from the outlet when there is lightning. Neglecting to do so may cause fire or damage to the product.

8. Do not block any ventilation openings. Install following the manufacturer’s instructions.

9. A polarized or grounding-type plug is recommended for this product. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. If the provided plug does not fit into your outlet, consult an electrician for replacement.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product.

11. If any laser equipment is used near the product, make sure the surface of the sensor is not exposed to the laser beam as that may damage the sensor module.

12. If you want to move the already installed product, be sure to turn off the power and then move or reinstall it.

13. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.

14. If cleaning is necessary, please use a clean cloth to wipe it gently. If the device will not be used for a long time, please cover the lens cap to protect the device from dirt.

15. Do not touch the camera’s lens or sensor module with fingers. If cleaning is necessary, please use a clean cloth to wipe it gently. If the device will not be used for a long time, please cover the lens cap to protect the device from dirt.

16. Use only attachments/accessories specified by the manufacturer.

17. Always use hardware (e.g. screws, anchors, bolts, locking nuts, etc.) compatible with the mounting surface and of sufficient length and construction to ensure a secure mount.

18. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the product.

19. Unplug this product when a cart is used. Use caution when moving the cart/product combination to avoid injury from tip-over.

20. Refer all servicing to qualified service personnel. Servicing is needed when the product has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped.

Follow these steps to prepare for mounting:

1. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

2. This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.38A (DWC-MB72Wi4TDMP) min.

3. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1 or PS2 as defined in UL62368-1.

4. Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

5. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.

Pass the wires through the mounting surface and make all necessary connections. You have two options for powering the camera:

1. Use a PoE Injector (required, sold separately) to connect data and power to the camera using a single Ethernet cable.

OR

2. Use a non-PoE Switch to connect data using an Ethernet cable, and use a separate power adapter to power the camera.

The waterproof cap set comes with two rubber rings. Use the rubber ring that is best sized for your network cable’s diameter.

NOTE: Cables with ø4.5mm to ø5.5mm thickness should use the black rubber ring. Cables over ø5.5mm in thickness should use the white rubber ring.

NOTE: To ensure a moisture seal, make sure the o-ring is in place between parts ‘c’ and ‘e’ of the cap assembly. In extreme environments, the use of an outdoor-rated sealer is recommended.

After assembling the waterproof cap components onto the network cable, connect it to the camera’s network port. For enhanced protection, you can wrap the connection with seal tape.

1. Mount the camera to the mounting surface and secure it using the screws and anchors included.

2. Loosen the pan and tilt screws at the base of the camera’s bracket to adjust the camera’s view and position.

3. Remove the protective film from the lens cover. Softly wipe the dome/lens cover with lens tissue or a microfiber cloth with ethanol to remove any dust or smudges left from the installation process.

To reset the camera, press the reset button for five (5) seconds. This will initiate a camera-wide reset of all the settings, including network settings.