DT RESEARCH 582TM (01) PDF Document

You can use a screen cleaning solution that is alcohol-free and non-abrasive to clean the touch screen of the DT RESEARCH 582TM. Cleaning with a micro-fiber cloth is recommended. Please spread the solution onto the cloth and then clean the touch screen.

To clean the Anti-microbial Enclosure of the DT RESEARCH 582TM:

• Use a soft/non-abrasive cloth moistened with water to clean the enclosure.
• If using a cleaner, an alcohol-free and oxide-free cleaning liquid is recommended.
• To prevent scratching the anti-microbial coating, please wipe gently.

The DT RESEARCH 582TM has a comprehensive set of I/O ports located along the lower rear edge of the unit. These include:

To insert or replace the hot-swappable batteries for the DT RESEARCH 582TM:

1. Open the battery lid.

2. Hold the battery with its yellow label facing backwards and insert it into the battery slot.

3. Close the battery lid. Make sure the lid shuts tightly when closing the lid.

Precautions when operating and handling the DT RESEARCH 582TM include:

• Always exercise care when operating and handling the Medical-Cart Computer.
• Never disassemble any portion of the enclosure, as this will void any product warranty on the Medical-Cart Computer.
• Do not use any AC/DC adapter other than the one provided with the device or a replacement acquired from the manufacturer.
• In the unlikely event that smoke, abnormal noise or strange odor is present, immediately power down the Medical-Cart Computer and disconnect all power sources. Please report the problem to your device provider immediately.

If your DT RESEARCH 582TM comes with battery packs, open the battery slot caps and then put in the battery packs one by one. If not, use the AC-DC adapter with the Medical-Cart Computer for the power supply. To activate the DT RESEARCH 582TM, push and quickly release the Power Button and the display will come on in a few seconds.

To put the DT RESEARCH 582TM into Standby mode, push and quickly release the Power Button.

To turn off the DT RESEARCH 582TM for extended storage, power off the device safely using any software function that “shuts down computer” provided in the software operating system.

The battery packs (optional) shipped with your device may be low in power. Please use the AC-DC adapter with the Medical-Cart Computer when setting up the device for the first time to fully charge the battery packs. You may charge the battery packs with them attached to the Medical-Cart Computer, or with the optional battery charger kit.

When the battery pack(s) is (are) charging, the blue-colored Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Try unplugging/replugging the AC-DC adapter to the Medical-Cart Computer a few times to activate the charging process.

To conserve power, use (push and quick release) the Power Button to put the device in “Standby” mode while not in use. Pushing briefly on the same button will wake up the system within seconds.

Avoid using the Power Button (“hold 4+ seconds” feature) to turn off the device. This form of hardware shutdown is intended to be a means of recovery from device lockups, and not as normal operation.

If connecting an external monitor to the DT RESEARCH 582TM (via HDMI port), you must power the Medical-Cart Computer with the provided AC-DC power adapter.

The Power/Battery LED statuses on the DT RESEARCH 582TM indicate the following:

• Blue indicates the battery is 25% to 100% charged
• Blinking blue indicates the battery is charging
• Orange indicates that the battery is between 11% to 25%
• Blinking Orange indicates that the battery is below 10%

The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT RESEARCH 582TM and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access.

When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc. Also, refer to the access point operating manuals for setting up the 802.11 access points.