CHRISTIE CINELIFE+ (CINELIFEPLUS) 2.0 (01) PDF DOCUMENT

Read all safety and warning guidelines before installing or operating the projector.

Warning! If not avoided, the following could result in death or serious injury.

TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be tripped over, or damaged by persons walking on or objects rolling over the cables.

This product must be installed within a restricted access location not accessible by the general public.

Only personnel who are trained on the precautions for the restricted access location can be granted entry to the area.

Install the product so users and the audience cannot enter the restricted area at eye level.

ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

High leakage current present when connected to IT power systems.

FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts specified by Christie.

FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

Lift equipment must be used to position the product.

Do not install or operate the projector in any position that does not meet the stated product specifications for alignment and orientation.

Caution! If not avoided, the following could result in minor or moderate injury.

Only Christie qualified technicians are permitted to open product enclosures.

Read all safety and warning guidelines before connecting to AC power.

Warning! If not avoided, the following could result in death or serious injury.

SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.

FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and power plug meet the appropriate local rating standards.

SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage and current, as specified on the license label.

SHOCK HAZARD! The UPS power cord must be inserted into an outlet with grounding.

SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning, removing components, or opening any enclosure.

Install the product near an easily accessible AC receptacle.

Caution! If not avoided, the following could result in minor or moderate injury.

FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

SHOCK HAZARD! Power supply uses double pole/neutral fusing.

Read all safety and warning guidelines before operating the projector laser.

Warning! If not avoided, the following could result in death or serious injury.

Do not operate the cinema projector without all of its covers in place.

LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the laser module.

Do not look directly into the lens when the light source is on. The extreme high brightness can cause permanent eye damage.

Possible hazardous optical radiation emitted from this product. (Risk group 3)

Read all safety and warning guidelines before installing the projector lamp.

Warning! If not avoided, the following could result in death or serious injury.

This procedure must be performed by Christie qualified technicians.

EXPLOSION HAZARD! Always wear protective safety clothing (gloves, jacket, face shield) approved by the manufacturer whenever the lamp door is open or when handling the lamp. Any local or federal specifications take precedence over Christie’s protective clothing recommendations.

Do not open the lamp door while the lamp is on.

EXPLOSION HAZARD! Allow sufficient time for the lamp to cool down before powering down the product, disconnecting it from AC, and opening the lamp door.

EXPLOSION HAZARD! Do not stress the glass of a lamp or bare bulb in any way.

EXPLOSION HAZARD! Lamps and bare bulbs, even when packaged, may explode if dropped or mishandled.

EXPLOSION HAZARD! Handle a lamp by the cathode and anode end shafts only. Do not handle the lamp by the glass.

EXPLOSION HAZARD! Do not over-tighten the lamp.

Do not look directly into the lens when the light source is on. The extreme high brightness can cause permanent eye damage.

FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated light beam of the projector.

Caution! If not avoided, the following could result in minor or moderate injury.

Improper installation of the lamp can damage the projector.

Incorrect lamp power supply and igniter connections can damage the product.

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to possible hazardous optical and thermal radiation being emitted.

Warning! If not avoided, the following could result in serious injury.

PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be permitted.

PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam within the hazard distance or install the product at the height that prevents exposure of spectators’ eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters/8.2 feet (US installations) or 2.0 meters/6.6 feet (global installations) above any surface upon which any persons are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0 meters (3.3 feet).

EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

A – Hazard zone. The region of space where the projection light from the projector is above emission limits for Risk Group 2. The light intensity may cause eye damage after a momentary or brief exposure (before a person can avert their eyes away from the light source). The light may cause skin burns to occur.

B – Hazard distance. Operators must control access to the beam within the hazard distance or install the product preventing potential exposure of the spectators’ eyes from being in the hazard distance.

C – No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0 meters (3.3 feet).

D – Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters/8.2 feet (US installations) or 2.0 meters/6.6 feet (global installations) above any surface upon which any persons are permitted to stand. If the vertical distance to hazard zone requirement (Zone D) is satisfied, the horizontal clearance distance (Zone C) is not needed.

E – Represents the top view of the projector.

F – Represents the side view of the projector.

The following updates have been made to the guide.

Updated the organization of the Introduction chapter and added a topic for viewing Christie University product training videos.

Updated the Understanding the Christie touch panel interface and web user interface topic to include the Discover icon and definition.

Removed the supported formats signal tables from the Video Input panel chapter. The signal tables are provided in a separate document.

Updated Creating a screen file and Editing screen file settings topics to include information about 2D keystone correction.

Added new topics:

Service mode

Customizing 3D mover delay

Creating a custom space file

Managing EDID files

Disabling ECC

Using 2D keystone correction

Keeping the test pattern on

Renaming an existing macro

The projector operates with the following power modes:

Understand the correct sequence for powering up and operating CP4440-RGB, CP4445-RGB, CP4450-RGB, and CP4455-RGB systems.

The connected chiller must always be turned on first and turned off only after the projector is turned off. Once the chiller is connected to AC and the chiller communication cable is connected to the projector, the projector controls the chiller automatically to maintain the required coolant temperature.

Christie recommends powering on the projector 30 minutes before use to allow time for the chiller to set the coolant to the set temperature.

The system is ready to operate when the following steps are completed:

1. The connected chiller unit is powered on.

2. The projector’s main power switches are on.

3. Communication between the projector and the connected chiller is confirmed and coolant temperatures are correctly maintained. If a thermal shutdown occurs in a dual projector installation, verify the chiller communication cables are connected correctly between each projector-chiller pair. This makes sure no cross-connection exists relative to the coolant lines.

Turn on the projector to display content or turn off the projector to conserve energy or service the projector.

In the right toolbar, select and hold Power.

Red, yellow, and green LEDs on the top and rear corners of the projector indicate the status of the projector. The LEDs can be solidly lit, flash frequently, or flash intermittently.

1. From the login page, in the User list, select a username.

2. Enter your password.

3. Select Login.

Select Logout.

Session Timeout automatically logs a user out after a pre-determined duration of inactivity when using the Touch Panel Control or the Web User Interface (UI).

1. In the navigation menu, select Service Setup.

2. Select Preferences.

3. Select General.

4. In the System area, select Session Timeout duration:

30 minutes-this is the default duration for Web UI.

1 hour

2 hours

5 hours

12 hours-this is only available for Web UI.

Never-this is only available for the Touch Panel Control and is the default.

1. Connect the projector to the theater network using an Ethernet cable.

2. Make sure the projector is not in Standby mode by selecting the recessed button between the USB-C port and the USB port on the Video Input panel. Pressing the recessed button transitions the projector from Standby to powered on.

3. Make sure the path in front of the lens is clear and ready for the IP address to be projected as continuing to step 4 turns on the light source and projects the IP address on the screen.

4. Once the unit is powered on, select and hold the Marriage button on the projector for 5 to 25 seconds. The projector turns on the light source and displays a test pattern with the projector’s IP address and any currently active alarms. The light source remains on.

5. To turn the light source off, select and hold the Marriage button for 5 to 25 seconds.

Use the following method to reset the projector IP address to the default value (192.168.206.110) and the subnet to 255.255.255.0 when no touch panel is installed.

1. Connect the projector to the theater network using an Ethernet cable.

2. Make sure the projector is not in Standby mode by selecting the recessed button between the USB-C port and the USB port on the Video Input panel. Pressing the recessed button transitions the projector from Standby to powered on. Before resetting the IP address to factory default, the light source turns on and remains on.

3. Once the unit is powered on, select and hold the Marriage button on the projector for 30 seconds. The IP address of the projector is reset to the default.

4. Once you have reset the IP address, turn off the light source by selecting and holding the Marriage button for 5 to 25 seconds.

1. In a web browser, enter the IP address of the projector. The default IP address is 192.168.206.110.

2. Log into the Web UI.

3. To access the projector menu, select the left navigation menu.

4. To upload or download files from the projector, navigate to the feature.

5. If the projector has a GDC IMB SR-1000 installed and configured, access the GDC IMB Web UI by navigating to the left navigation menu and selecting IMB.

To turn on or off the touch panel, select the Power button (A) on the top of the touch panel.

To turn on or off the light source, in the right toolbar, select and hold Light. If turning on the light source when the projector power is off, power is turned on automatically.

For laser projector models, allow the projector to cool down for 3 minutes after turning it off.

For xenon projector models, allow the projector to cool down for 10 minutes after turning it off.

If you turn on the laser source while the projector is cooling down, the lasers turn on.

Open the shutter (douser) to display light on the screen, or close the shutter to remove light from the screen.

1. In the right toolbar, select and hold Douser.

If the shutter was closed, the shutter opens.

If the shutter was open, the shutter closes.

2. If the shutter is not functioning, use the Permit light source activation when shutter is nonfunctional option to permit activation of the light source. To enable this option, select Service Setup > Preferences > Lens/ILS and enable Permit light source activation when shutter is nonfunctional. To avoid damage to the projector, only enable this option when the shutter can be verified as open.

1. In the left navigation menu, select Service Setup > Time Setup.

2. Switch to the Projector Time Settings tab.

3. Select Sync to NTP Server.

4. Select New NTP Server.

5. In the Add New NTP Server dialog, select a local or a public NTP server:

To use a local NTP server, select Local Server and enter the IP address in the IP Address field.

To use a public NTP server, select Public Server and complete the Country and Server fields.

6. To test the connection, select Test.

7. Select Add.

1. In the left navigation menu, select Service Setup > Time Setup.

2. Switch to the Projector Time Settings tab.

3. Select Sync to NTP Server.

4. In the NTP Server Address list, select an NTP server.

5. Select Delete.

6. At the confirmation dialog, select Delete.

1. In the left navigation menu, select Service Setup > Time Setup.

2. Select Time Zone.

3. In the Region list, select a region.

4. In the Time Zone list, select the time zone.

5. To automatically adjust the projector time to follow Daylight Saving Time, select Automatically adjust for Daylight Saving Time. The color of the slider changes to green to indicate it is active.

6. Select Save.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select General.

3. In the System area, select a time format option:

To use the 12-hour format, select 12 Hours.

To use the 24-hour format, select 24 Hours.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select General.

3. From the Projected Image Orientation list, select the required orientation for the projected image.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select General.

3. In the Projector Hostname field, enter a name.

4. Select Update.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select General.

3. In the Temperature Units list, select Celsius or Fahrenheit.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Automation.

3. To disable serial authentication requirement, toggle off Require Serial Authentication.

1. In the top right of the dashboard, select Status. You can also select Status from the left navigation menu.

2. Navigate to the status category you want to view and select it.

GPIO inputs

The 5 VDC (pin 19 and pin 20) is intended for use to supply the inputs.

GPIO outputs

Outputs are solid state relays with a 1 A AC/DC rating at up to 48 V.

Service mode limits the laser power to a user-defined lower power for use when performing optical alignment.

1. Log in as service.

2. In the left navigation menu, select Service Setup > Preferences.

3. Select Service Mode.

4. To enable laser service mode, toggle on Enable Service Mode.

5. In the Warning dialog, to edit the maximum drive laser levels, select Enable. The default levels are set to 0.

6. Enter the individual maximum drive levels for red, green, and blue. A message appears in bottom right corner when the change is successful. Status warning displays updated entry for each LOS Drive Limit with the updated drive limit values.

Restore the maximum drive laser levels to the original values.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Service Mode.

3. To disable laser service mode, toggle off Enable Service Mode.

4. In the Warning dialog, verify the projector is safe to operate at full brightness without restriction.

5. Select Disable. All maximum driver levels restore to 0. Status page displays LOS Drive Limits as Disabled.

1. Turn on the light source.

2. In the Warning dialog, verify the requirements are met.

3. If requirements are met, select Continue.

4. If requirements are not met, select Cancel.

5. Select Manual Laser Control.

6. To enable the white display test pattern, toggle on Display White Test Pattern. The RGB maximum limits are the same as the values defined in the service mode setup.

7. To restore the values to the original, disable service mode.

This only applies to: CP2415-RGB, CP2420-RGB, CP4415-RGB, CP4420-RGB, CP4425-RGB, CP4435-RGB.

1. Log in as service.

2. Turn on the laser.

3. For systems upgraded to v1.5.0 and already using the calibration file, set a channel to use the appropriate calibration file and activate the channel.

4. Display a test pattern, such as DC4K 17 L Point, to locate the center of the screen.

5. Set up the color meter to aim at the center of the screen.

6. In the left navigation menu, select Laser Settings > Laser Power/LiteLOC Setup.

7. Select Display White Test Pattern.

8. To create a new laser file, select Create.

9. In the Create dialog, enter a name for the new laser file and select Create.

10. In the White Coordinates dialog, set the required white point. For a typical cinema setup, the white point is Digital Cinema Initiative (DCI) white x=0.314 and y=0.351.

11. Select Apply.

12. Adjust the brightness level until you achieve the required brightness at the specified white point.

13. If the laser file will be associated with a 3D channel, complete the following steps:

a) Engage the 3D system in the light path by enabling 3D Sync when selecting the test pattern.

b) Mount a 3D glass or filter on the color meter to measure the brightness.

c) Select 3D Sync on the LiteLOC™ setup page.

d) Adjust the brightness level until you achieve the required brightness while the 3D system is engaged.

14. To save the new laser file, select Save.

This only applies to: CP4440-RGB, CP4445-RGB, CP4450-RGB, CP4455-RGB.

1. Log in as service.

2. Turn on the laser.

3. For systems upgraded to v1.5.0 and already using the calibration file, set a channel to use the appropriate calibration file and activate the channel.

4. Display a test pattern, such as DC4K 17 L Point, to locate the center of the screen.

5. Set up the color meter to aim at the center of the screen.

6. In the left navigation menu, select Laser Settings > Laser Power/LiteLOC Setup.

7. Select the Display White Test Pattern slider.

8. To create a new laser file, select Create.

9. In the Create dialog, enter a name for the new laser file and select Create.

10. For CP4440-RGB and CP4450-RGB models only, set the maximum expected humidity. The projector uses this information and the ambient temperature to determine the optimum maximum brightness allowed.

11. In the White Coordinates dialog, set the required white point. For a typical cinema setup, the white point is Digital Cinema Initiative (DCI) white x=0.314 and y=0.351.

12. Select Apply.

13. Adjust the brightness level until you achieve the required brightness at the specified white point.

14. If the laser file will be associated with a 3D channel, complete the following steps:

a) Engage the 3D system in the light path by enabling 3D Sync when selecting the test pattern.

b) Mount a 3D glass or filter on the color meter to measure the brightness through the glasses.

c) Select 3D Sync on the LiteLOC™ setup page.

d) Adjust the brightness level until you achieve the required brightness while the 3D system is engaged.

15. To save the new laser file, select Save.

1. Log in as service.

2. Turn on the laser.

3. Display a test pattern, such as DC4K 17 L Point or DC2K 17 L Point, to locate the center of the screen.

4. In the left navigation menu, select Laser Settings > Laser Power/LiteLOC Setup.

5. To begin modifying the settings, select Display White Test Pattern.

6. From the Laser File list, select the laser file to edit.

7. For external chiller-based projectors only, set the maximum expected humidity. The projector uses this information and the ambient temperature to determine the optimum Chiller set temperature.

8. In the White Coordinates dialog, set the required white point.

9. Select Apply.

10. Set the brightness levels as required for your projection environment and allow the projector to stabilize for a few minutes. System stability may be affected if you set a power level below the minimum power level recommended.

11. If white or brightness is not at the target level, adjust the settings to achieve the target and allow the projector to re-stabilize for an additional three to five minutes.

12. To save the new settings, select Save.

1. In the left navigation menu, select Laser Settings > Laser Power/LiteLOC Setup.

2. From the Laser File list, select the file to copy.

3. To save the new laser file, select Save As.

4. Enter a new name for the laser file and then select Save.

5. Adjust the settings as required for the new configuration.

6. Select Save.

1. In the left navigation menu, select Laser Settings > Laser Power/LiteLOC Setup.

2. In the Laser File list, select the file to delete.

3. Select Delete.

4. To confirm the deletion, select Delete.

Re-doing this calibration is required if the following is replaced:

Color sensor board

Christie recommends re-doing this calibration if any of the following are replaced:

Light engine

Lens

Light source

Screen

Port window

Any other optical components in the optical path between the light source and the screen

After replacing these components, check the accuracy of the color point and if unsatisfactory, re-do this calibration.

LiteLOC™ sensor-to-screen calibration requires the following:

Spectroradiometer

Service user is the minimum level user access

The recommended workflow is as follows:

1. Create a new calibration file.

2. Recalibrate the calibration file, if required.

3. Edit the existing calibration file parameters on the Sensor-to-screen menu, if required.

4. Verify the calibration, if required.

5. Add the calibration file to the Channel Setup.

1. Set up a spectroradiometer to obtain screen measurements later in the process.

2. In the left navigation menu, select Color Settings > Sensor-to-screen Calibration.

3. To create a new calibration file, select Create. The projector checks if the light source is on and the douser is open. If either condition is not met, a warning dialog is displayed prompting you to make sure these conditions are met before starting the wizard.

4. In the Create dialog, enter a name for the new calibration file and select Create.

5. In step 1 of the Sensor-to-screen Calibration wizard, set the maximum brightness and color point.

a) Enable the Display White Test Pattern option.

b) Adjust the RGB sliders to set the brightness and color point.

c) Select Next.

6. Wait 20 minutes for the projector to stabilize or select Skip during the stabilization time period.

7. In step 2 of the Sensor-to-screen Calibration wizard, measure and enter the screen values.

a) To trigger the measurement at a specific operating point, under Sensor to screen, select Capture. The projector automatically sets the red, green, and blue output laser powers to the pre-determined settings. A 30 second countdown begins to allow the projector white point and brightness to stabilize. At the end of the countdown period, the Color Sensor values fields are automatically populated.

b) When the countdown ends, take x, y, and fL measurements using the spectroradiometer.

c) Under Measured Values, using the numeric keypad record the associated spectroradiometer values for x, y, and fL.

d) Repeat steps a to c for the remaining drive percentage set points until all x, y, and fL values are entered.

e) Once all the color sensor and measured values are entered for all rows, select Apply and Save.

8. Verify and complete the calibration.

a) Select a white point to measure by selecting either the DCI, D65, or Custom white point buttons.

b) Using a spectroradiometer, measure screen x and y values at the center of the screen.

c) When complete, select Finish.

1. Select Menu > Color Settings > Sensor-to-screen Calibration.

2. Select a user-defined calibration file to recalibrate.

3. Select Recalibrate.

4. In step 1 of the Sensor-to-screen Calibration wizard, set the maximum brightness and color point.

a) Enable the Display White Test Pattern option.

b) Adjust the RGB sliders to set the brightness and color point.

c) Select Next.

5. Wait 20 minutes for the projector to stabilize or select Skip during the stabilization time period.

6. In step 2 of the Sensor-to-screen Calibration wizard, measure and enter the screen values.

a) To trigger the measurement at a specific operating point, under Sensor to screen, select Capture. A 30 second countdown begins to allow the projector white point and brightness to stabilize. At the end of the countdown period, the Color Sensor values fields are automatically populated.

b) When the countdown ends, under Measured Values, using the numeric keypad capture and record the associated spectroradiometer values for x, y, and fL.

c) Repeat steps a and b for the remaining drive percentage set points until all x, y, and fL values are entered.

d) Once all the color sensor and measured values are entered for all rows, select Apply and Save.

7. Verify and complete the calibration.

a) Select a white point to measure by selecting either the DCI, D65, or Custom white point buttons.

b) Using a spectroradiometer, measure screen x and y values at the center of the screen.

c) When complete, select Finish.

1. Select Menu > Color Settings > Sensor-to-screen Calibration.

2. Select a user-defined calibration file.

3. Edit any of the x, y, or fL values by selecting the field under Measured Values and using the numeric keypad to enter the updated value.

x and y value range: 0.0001 to 0.9999

fL value range: 0.01 to 9999.99.

4. To save the updated file to the projector, select Save.

1. Navigate to Menu > Color Settings > Sensor-to-screen Calibration.

2. In the right toolbar, select Test Patterns.

3. Select the White test pattern.

4. Close the Test Patterns window.

5. Select Verify Calibration. Step 3 of the Calibration wizard opens.

6. Verify and complete the calibration.

a) Select a white point to measure by selecting either the DCI, D65, or Custom white point buttons.

b) Using a spectroradiometer, measure screen x and y values at the center of the screen.

c) When complete, select Finish.

1. In the left navigation menu, select Channel Setup.

2. Select the channel you want to add the calibration file to.

3. From either the 2D Sensor-to-Screen Calibration File or 3D Sensor-to-Screen Calibration File list, select the calibration file.

4. Select Save.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. Turn on the circuit breaker for the projector.

2. Select and hold Power for two seconds.

3. Select and hold Lamp On for two seconds.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. Select and hold Lamp Off for two seconds.

2. Select and hold Power Off for two seconds.

3. Wait for the lamp to cool down and then disconnect the projector from AC power and turn off the circuit breaker for the projector.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. In the left navigation menu, select Lamp Settings > Lamp Power/LiteLOC Setup.

2. Increase or decrease the Power % value.

3. Select Set Target.

4. Select Enable LiteLOC.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. In the left navigation menu, select Lamp Settings > Lamp Power/LiteLOC Setup.

2. Increase or decrease the Power % value.

3. Save the changes.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe. This feature is not meant for regular use.

1. Select Service Setup > Preferences > Light Source.

2. Select Enable Lamp Overdrive.

3. At the confirmation prompt, select OK.

4. To disable the lamp overdrive, perform a factory restore.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

Before adjusting LampLOC, make sure the lamp is on and the douser (shutter) is open during the adjustment. Christie recommends a 10 minute warm-up.

1. In the left navigation menu, select Lamp Settings > LampLOC.

2. Toggle the Display White test pattern button.

3. Select Align Auto.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. In the right menu, select Test pattern.

2. Select RGB-12bit-Full Screen White.

3. Mount a light meter on a tripod and center it with the lens.

4. In the left navigation menu, select Lamp Settings > Lamp LOC.

5. Select the directional arrows to adjust the value displayed in the Z field. The brightness reading in front of the lens should be maximized.

6. Select the directional arrows to adjust the values displayed in the X and Y fields. The brightness reading in front of the lens should be maximized.

7. Repeat steps 5 to 6 taking your readings at the screen instead of at the lens.

8. If required, run LampLOC > Auto Align.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

In the left navigation menu, select Lamp Settings > Lamp Manager.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. In the left navigation menu, select Service Setup > Preferences.

2. In the Alarm Triggers area, select Lamp Expiry.

This only applies to: CP2415-Xe, CP2420-Xe, CP4420-Xe.

1. In the left navigation menu, select Service Setup > Preferences.

2. In the Alarm Triggers area, select Lamp Half Life.

* Available when the IMB-S4 is installed.

The Manager role has limited access to the Service Setup menu.

The Operator role has limited access to the Scheduler menu.

A Marriage role exists for the purpose of marrying a projector and the installed media block. It has similar permissions to the Installer role.

1. In the left navigation menu, select Service Setup > User Accounts.

2. Select +.

3. Complete the Name, Permissions, Password, and Confirm Password fields.

4. Select Save.

1. In the left navigation menu, select Service Setup > User Accounts.

2. In the left pane, select a user account.

3. Select Edit.

4. In the Permissions list, select a new permissions setting.

5. Select Save.

1. In the left navigation menu, select Service Setup > User Accounts.

2. In the left pane, select a user account.

3. Select Edit.

4. Select Change password.

5. Complete the New Password and Confirm Password fields.

6. Select Save.

1. In the left navigation menu, select Service Setup > User Accounts.

2. In the left pane, select a user account.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. Connect the Ethernet cable from the theater network to the Management port on the input panel.

2. In the left navigation menu, select Service Setup > Network Settings.

3. Select the Ethernet Settings tab.

4. In the Port list, select Management.

5. Enter the network settings:

To obtain the network settings automatically, select Automatic.

To enter the settings manually, select Manual and complete these fields:

6. Select Save.

On CineLife+ projectors, SNMP is enabled by default.

1. In the left navigation menu, select Service Setup > Network Settings.

2. Select the SNMP tab.

3. Select the SNMP slider. The color of the slider changes to blue to indicate it is active.

4. In the SNMP Settings area, select the SNMP version.

5. Complete the Trap Receiver IP fields.

6. In the Blocked SNMP Traps area, select the SNMP traps you want to block.

7. Select Save.

1. In the left navigation menu, select Service Setup > Network Settings.

2. Select the SNMP tab.

3. Select Download MIB.

4. Depending on your browser settings, browse to the location where you want to save the MIB file.

5. In the Name field, enter a name for the MIB file.

6. Select Accept.

7. Select OK.

Tasks include the following:

Installing the IMB in the projector

Connecting portable or enterprise storage

Managing content, including key delivery message (KDM) and security keys

Managing and scheduling playback

Setting up audio

Setting up playback automation

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Configuration.

3. Navigate to the 3D Mover Delay section.

4. In the 3D Mover Delay (ms) field, enter a value in milliseconds between 1 and 2000. The default value is 0.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select IMB.

3. In the Type list, select the manufacturer of the IMB model.

4. When the system prompts you to reboot the projector, select Reboot.

5. After the projector has restarted, log in with your user account.

You cannot complete marriage remotely because you must select the Marriage button on the input panel during the marriage process.

1. Verify the marriage ring is installed correctly and an anti-tamper alarm does not appear on the touch panel.

2. In the left navigation menu, select Service Setup > Marriage Setup.

3. Select Start and complete the Marriage Setup wizard. At the Arming stage, enter the Marriage password.

4. Select Finish.

1. To set the type of IMB, select Service Setup > Preferences.

2. Select IMB.

3. Enable the IMB Powered in Standby option.

1. In the left navigation menu, select Channel Setup.

2. Select + Create New Channel.

3. In the Enter a new file name field, enter the channel name.

4. Select Create.

5. Complete these fields:

6. Select Create.

1. In the left navigation menu, select Channel Setup.

2. Select + Create New Channel.

3. In the Enter a new file name field, enter the channel name.

4. Select Create.

5. Complete these fields:

6. Select Create.

1. In the left navigation menu, select Channel Setup.

2. Select + Create New Channel.

3. In the Enter a new file name field, enter the channel name.

4. Select Create.

5. Complete these fields:

6. Select Create.

1. In the left navigation menu, select Channel Setup.

2. Select + Create New Channel.

3. In the Enter a new file name field, enter the channel name.

4. Select Create.

5. Complete these fields:

6. Select Create.

1. In the right toolbar, select All Channels. The All Channels window displays the available channels and the active channel is highlighted.

2. Select a channel. In the Channel Setup panel, a green checkmark indicates the active channel.

3. Select Close.

1. In the left navigation menu, select Channel Setup.

2. In the left pane, select a channel.

3. Edit the channel settings.

4. Select Save.

1. In the left navigation menu, select Channel Setup.

2. In the left pane, select a channel.

3. Select Rename Channel.

4. Enter a new name.

5. Select Rename.

1. In the left navigation menu, select Channel Setup.

2. In the left pane, select a channel.

3. Select Save As.

4. Enter a name for the new channel and select Save.

5. If input type changes, check all settings.

In the left navigation menu, select Channel Setup. Under Channel Setup, the available channels are displayed in the left pane. A green checkmark indicates the active channel.

Alternatively in the right toolbar, select All Channels. The Channels window displays the available channels and the active channel is highlighted.

1. In the left navigation menu, select Channel Setup.

2. In the left pane, select a channel.

3. To move the channel up or down the list, select the up or down arrow.

1. In the left navigation menu, select Channel Setup.

2. In the left pane, select a channel.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Color Settings > Color Space File Setup.

2. Select Import Color Space File.

3. Browse to the .xml file in one of the following ways.

Using the touch panel control-Browse for the file on the USB flash drive.

Using the web user interface-Browse for the file on your computer.

4. Open the file in one of the following ways.

Using the touch panel control-Select Accept.

Using the web user interface-Select Open.

1. Activate the channel using the light source file the MCGD file is being created for.

2. Turn on the light source and allow it to operate for 20 minutes.

3. In the left navigation menu, select Color Settings > MCGD File Setup.

4. Select Create.

5. Enter a name for the MCGD file and select Create.

6. If the MCGD file will be associated with a 3D channel, select the 3D Sync slider.

7. In the red area of the chromaticity image, select the empty circle. The test pattern is automatically displayed.

8. Measure the red chromaticity with the colorimeter.

9. Enter the red chromaticity value in the x field.

10. Select Next and enter the red chromaticity value in the y field.

11. For the green, blue, white (center circle), and black chromaticity measurements, repeat steps 7 to 10.

12. Select Save.

1. In the left navigation menu, select Color Settings > MCGD File Setup.

2. In the MCGD File list, select a MCGD file.

3. Edit the measured color values.

4. Select Save.

1. In the left navigation menu, select Color Settings > MCGD File Setup.

2. In the MCGD File list, select a MCGD file.

3. Select Save As.

4. Enter a name for the MCGD file and select Save.

1. In the left navigation menu, select Color Settings > MCGD File Setup.

2. In the MCGD File list, select a MCGD file.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. Turn on the light source and allow it to operate for 20 minutes.

2. In the left navigation menu, select Color Settings > TCGD File Setup.

3. Select Create.

4. Enter a name for the TCGD file and select Create.

5. To display test clips automatically when selecting a color in the chromaticity image, select Automatically Display Test Clip.

6. To modify the white clipping values and improve image detail in bright areas of the image, select Use White Clip.

7. Select the option button in the red area of the chromaticity image to display the red test pattern.

8. Measure the red chromaticity with the colorimeter.

9. Enter the red chromaticity values in the Red x and Red y fields.

10. Adjust the Gain value to modify the color brightness.

11. For the magenta, blue, cyan, white, yellow, and green chromaticity measurements, repeat steps 7 to 10.

12. To adjust the color of the white light in a specific area of the screen, select White Tolerance and a screen area.

13. Select Save.

1. In the left navigation menu, select Color Settings > TCGD File Setup.

2. In the TCGD File list, select a TCGD file.

3. Edit the TCGD file settings.

4. Select Save.

1. In the left navigation menu, select Color Settings > TCGD File Setup.

2. In the TCGD File list, select a TCGD file.

3. Select Save As.

4. Enter a name for the TCGD file and select Save.

1. In the left navigation menu, select Color Settings > TCGD File Setup.

2. In the TCGD File list, select a TCGD file.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select EDID File Import.

3. Select Import EDID.

4. Browse to the location of the EDID file.

5. Select the EDID file.

6. Select Open.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select EDID File Import.

3. Navigate to the EDID file.

4. Select Delete.

On CineLife+ projectors, the ILS is enabled by default.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Lens/ILS.

3. In the right pane, select the ILS Installed slider. The color of the slider changes to blue to indicate the ILS is active.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. Select Create.

3. Enter a name for the ILS file and select Create.

4. In the Lens position area, select the forward, backward, left, or right arrow icons to move the position of the image on the screen.

5. In the Focus area, select Up or Down to increase or decrease image focus.

6. In the Zoom area, select Up or Down to increase or decrease image zoom.

7. Select Save.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. Select Auto Calibrate.

3. In the confirmation dialog, select Continue.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. On the right side, in the ILS File list, select an ILS file.

3. Modify the ILS file settings.

4. Select Save.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. In the ILS File list, select the ILS file you want to copy.

3. Select Save As.

4. Enter a name for the ILS file and select Save.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. In the ILS File list, select the ILS file you want to delete.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. Select Reset Lens.

3. In the confirmation dialog, select Continue.

1. In the left navigation menu, select Image Settings > ILS File Setup.

2. Use the arrow to select an ILS file to store the ECC settings.

3. On the ILS File Setup page, select ECC.

4. Set the Screen Type to Flat or Scope.

5. Set the Sprite Color to Move and Show.

6. Select a Step Size to control the granularity of the steps from coarse (1/8 pixel per step) to fine (1/64 pixel per step) when using the directional pad.

7. Choose a corner by selecting the circle at a corner of the dashed rectangle.

8. Use the directional pad to move the sprites towards the center of the screen.

9. Adjust each sprite so they overlap to create a single white sprite.

10. To set the convergence for that corner of the screen, select Apply.

11. Repeat steps 7 to 10 for the remaining corners.

12. If necessary, reset the correction back to zero (no correction) or the previously saved correction by selecting Reset. In the Reset dialog, reset the current corner or all four corners. When the locations and value are set, select Reset.

13. To save the current ECC settings, when the convergence is complete, select Save beside the ILS file named at the top of the panel.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Test Patterns.

3. Select Uncorrected Geometry. Cropping, keystone, warp, and ECC correction are disabled.

1. In the left navigation menu, select Image Settings > Source File Setup.

2. Select Create.

3. Enter a name for the source file and select Create.

4. In the Source Media Resolution area, adjust the width and height of the source media.

5. Select an aspect ratio or enter a custom aspect ratio for the source media.

6. In the Position area, adjust the horizontal and vertical position of the source media.

7. Select Save.

1. In the left navigation menu, select Image Settings > Source File Setup.

2. In the Source File list, select a source file.

3. Modify the source file settings.

4. Select Save.

1. In the left navigation menu, select Image Settings > Source File Setup.

2. In the Source File list, select the source file you want to copy.

3. Select Save As.

4. Enter a name for the source file and select Save.

1. In the left navigation menu, select Images Settings > Source File Setup.

2. In the Source File list, select the source file you want to delete.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Image Settings > Screen File Setup.

2. Select Create.

3. Enter a name for the screen file and select Create.

4. To crop the image in a specific location, select one of the screen icons.

5. To adjust the amount of cropping on the X or Y axis, move the slider up or down.

6. Select Save.

1. In the left navigation menu, select Image Settings > Screen File Setup.

2. In the Screen File list, select a screen file.

3. Modify the screen file settings.

4. Select Save.

1. Select Image Settings > Screen File Setup.

2. In the Screen File list, select the screen file you want to copy.

3. Select Save As.

4. Enter a name for the source file and select Save.

1. In the left navigation menu, select Image Settings > Screen File Setup.

2. In the Screen File list, select the screen file you want to delete.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. Using Christie Mystique, create the required warp file.

2. Using Mystique, upload the warp file to the projector.

3. On the projector touch panel, navigate to Image Settings > Warp File Setup.

4. To activate the warp file, find the file name in the Warp File list and select Activate.

If your image suffers from vignetting, the lens has reached the end of its offset travel range. If your installation does not allow the image to be centered with the center of the screen, move the entire projector in the direction of lens travel.

When making the adjustments, set the light source to minimum power.

1. If the image suffers from slight keystone effect, it can be corrected with electronic cropping.

2. If the keystone effect is severe, unevenly adjust the feet to compensate for projector tilt. Christie recommends using the lens offset to align the center of the image to the center of the screen before correcting the keystone effect.

3. If one side of the image is longer than another, adjust the tilt and level of the projector.

When Keystone is enabled, features such as masking, electronic color correction (ECC), and other warping operations defined in the active channel are disabled.

1. In the left navigation menu, select Image Settings > Screen File Setup.

2. Toggle on Keystone.

3. Select a corner correction point to adjust.

To create top masking (for 1.85 screens):

a) Install movable flat black panels or curtains along the top edge of the screen.

b) Raise the curtain for flat images or lower the curtain for scope images.

To create side masking (for 2.39 screens):

a) Install movable flat black panels or curtains along each side of the screen.

b) Close the curtain for flat images or open the curtain and zoom for scope images.

1. In the right toolbar, select Test Patterns.

2. Select Full Screen or Uncorrected Colors.

3. Select a test pattern.

4. To display a 2D test pattern in 3D mode, select the 3D Sync option.

5. To change the frame rate of the test pattern display, select from the available Frame Rate options:

For 2D test patterns, the available frame rates are 24, 30, 48, and 60 Frames Per Second (FPS). The default value is 24 FPS.

For 3D test patterns, the available frame rates are 48 and 60 FPS. The default value is 48 FPS.

1. In the right toolbar, select Test Patterns.

2. Select Test Pattern Off.

1. In the right toolbar, select Test Patterns.

2. In the upper right corner, select Edit.

3. Select Import.

4. Browse to the location of the test pattern file.

5. Select the test pattern file.

6. Select Open.

7. In the upper right corner, select Done.

A test pattern with RGB in the name cannot be deleted.

1. In the right toolbar, select Test Patterns.

2. In the upper right corner, select Edit.

3. Select a test pattern.

4. Select Delete.

5. To confirm the deletion, select Delete.

6. In the upper right corner, select Done.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select Test Patterns.

3. Toggle on Keep Test Pattern On After Channel Change.

1. In the left navigation menu, select Scheduler.

2. To enable scheduled events, move the Scheduler is off slider to the right.

3. To select a date for the scheduled event, select Calendar.

4. Select the week.

5. Select a square below the date and next to the time you want the event to run.

6. Select + New Event.

7. In the Macros tab, select a macro.

8. Select the start time.

9. Select the start date.

10. To repeat the event daily, weekly, or monthly:

a) Select the Recurrence slider.

b) Select the frequency of the recurrence.

c) Select the days or months you want the playlist, content, or automation event to play.

d) To select an end date for the schedule, select Calendar.

11. To prevent the scheduled event from being overwritten, select the Lock Event slider.

12. Select Create Event.

1. In the left navigation menu, select Scheduler.

2. In the calendar view, select the scheduled event.

3. Select Edit.

4. Edit the scheduled event settings.

5. Select Update Event.

1. In the left navigation menu, select Scheduler.

2. In the calendar view, select the scheduled event.

3. Select Copy.

4. Select a square below the date and next to the time you want the event to run.

5. Select Paste.

6. Adjust the settings for the scheduled event.

7. Select Paste Event.

1. In the left navigation menu, select Scheduler.

2. At the top of the calendar, select the day with the events you want to copy.

3. Select Copy.

4. At the top of the calendar, select the new target day.

5. Select Paste. Only unlocked events are copied to the new day.

1. In the left navigation menu, select Scheduler.

2. In the calendar view, select the scheduled event.

3. Select Cut.

4. Select the new date in the calendar.

5. Select Paste.

6. Adjust the settings for the scheduled event.

7. Select Paste Event. Only unlocked events are copied.

1. In the left navigation menu, select Scheduler.

2. In the calendar view, select the scheduled event.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Scheduler.

2. At the top of the calendar, select the target day.

3. Select Clear Day.

4. To confirm the change, select Clear Day.

1. In the left navigation menu, select Service Setup > Preferences.

2. Select General.

3. In the Scheduler area, select the day of the week to start the scheduler.

1. In the left navigation menu, select Scheduler.

2. To disable scheduled events, move the Scheduler is on slider to the left. The color of the slider changes to grey to indicate it is inactive.

* Available when the IMB-S4 is installed.

By default, the projector is configured with a macro using a building fire alarm as the trigger. If the projector is connected the building’s fire alarm system (recommended installation), the default FIRE_ALARM macro puts the projector into Standby mode if a fire alarm occurs. You can also create a custom macro that uses the fire alarm trigger or edit the default fire alarm macro to perform other actions as needed.

Christie provides three JNIOR libraries.

The following built-in commands are available for Dolby CP650, CP750, CP850, CP950, and CP950A devices:

If you need to control additional functions and a built-in command is not available, send a command string in a macro. For example, send this command to enable surround boost on the Dolby CP750: cp750.sys.surround_boost 1\\0D. Make sure you include a carriage return (\\0D) at the end of each command.

1. In the left navigation menu, select Automation > Macro Editor.

2. Select + Create New Macro.

3. Enter a name for the macro. The Name field cannot contain spaces.

4. Select the macro type.

5. Select Create.

6. Add an action item to the macro:

a) In the right pane, select +.

b) In the Add New Action Item dialog, select My Auditorium.

c) Under Automation or Projector, select an action item.

7. Select Create.

8. To save the macro, select Save.

9. To test the macro, select Test.

1. In the right pane, select Macro Selection.

2. Select a macro.

1. In the left navigation menu, select Automation > Macro Editor.

2. In the left pane, select a macro from the list.

3. Add an action item to the macro:

a) In the right pane, select +.

b) Under Automation, Playback, or Projector, select the action item.

4. Select Create.

5. To save the macro, select Save.

6. To test the macro, select Test.

1. In the left navigation menu, select Automation > Macro Editor.

2. In the left pane, select a macro.

3. In the right pane, select +.

4. In the Add New Action Item dialog, select Macros.

5. Select a macro.

6. Select Create.

7. To save the macro, select Save.

8. To test the macro, select Test.

1. In the left navigation menu, select Automation > Macro Editor.

2. In the left pane, select the existing macro to rename.

3. Select Edit.

4. In the Confirmation dialog, select one of the following:

Continue-Select this option to proceed with renaming and continue to step 5.

Cancel-Select this option to terminate the action.

5. In the Edit Macro dialog, enter the new name for the macro.

6. Select Save.

1. In the left navigation menu, select Automation > Macro Editor.

2. In the left pane, select a macro.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Automation > My Auditorium Devices.

2. Select + New Device.

3. In the Name field, enter a name for the device. The Name field cannot contain spaces.

4. In the Device Type list, select the device type.

5. In the Select Device list, select the device.

6. Select Add.

7. Complete these fields:

IP Address-The IP address of the automation device.

Port-The port used by the automation device to communicate with the projector.

Username-The username used to access the automation device.

Password-The password used to access the automation device.

Keep Alive Message-The message value sent to the automation device to make sure the projector is not disconnected when inactive.

Keep Alive Interval (ms)-The time interval (in milliseconds) for sending the Keep Alive Message to the automation device.

8. Select Save.

1. In the left navigation menu, select Automation > My Auditorium Devices.

2. In the left pane, select an automation device.

3. Modify these fields:

IP Address-The IP address of the automation device.

Port-The port used by the automation device to communicate with the projector.

Username-The username used to access the automation device.

Password-The password used to access the automation device.

Keep Alive Message-The message value sent to the automation device to make sure the projector is not disconnected when inactive.

Keep Alive Interval (ms)-The time interval (in milliseconds) for sending the Keep Alive Message to the automation device.

4. Select Save.

1. In the left navigation menu, select Automation > My Auditorium Devices.

2. In the left pane, select an automation device.

3. Select Delete.

4. To confirm the deletion, select Delete.

1. In the left navigation menu, select Automation > Device Input Triggers.

2. Select + New Global Trigger.

3. Complete the Name, Source, and Trigger Event fields. The Name field cannot contain spaces.

4. In the Macro Name list, select the macro that will run on trigger detection.

5. Select Add.

1. In the left navigation menu, select Automation > Device Input Triggers.

2. To the right of the global trigger you want to edit, select Edit.

3. Edit the global trigger settings.

4. Select Save.

1. In the left navigation menu, select Automation > Device Input Triggers.

2. To the right of the global trigger, select Delete.

3. To confirm the deletion, select Delete.

1. In the left navigation menu, select Automation > Device Libraries.

2. Select Import Device Library.

3. Browse to the location of the device library file.

4. Select the file and select Open.

1. If the device library is not in the list, import it.

2. In the left navigation menu, select Automation > Device Libraries.

3. To the right of the device in the View Library column, select View Library. Review the list of actions available for the device.

4. To exit the dialog, select OK.

1. In the left navigation menu, select Automation > Device Libraries.

2. To the right of the device library, select Delete.

3. To confirm the deletion, select Delete.

1. Save the license file in one of the following ways.

Using the touch panel control-Save the file to a USB flash drive.

Using the web user interface-Save the file to a location on your computer.

2. If using the touch panel control, insert the USB flash drive in the USB port on the projector faceplate.

3. In the right toolbar, select Rental Mode.

4. In the Rental Licenses window, select Import License.

5. In the Open File dialog, navigate to the folder containing the license ZIP file and select the file from the list.

6. Select Open.

1. In the right toolbar, select Rental Mode.

2. In the Rental Licenses window, view the following information:

Days remaining

Expiry date

When a license is nearing expiration, the license information box changes color and the system displays an alert on the Rental Mode icon.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. Select New Backup.

3. Enter a name for the backup file and select Backup.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. If using the web user interface (UI), select a backup file and select Download. The file automatically downloads to the computer’s Downloads folder.

3. If using the touch panel control, insert a USB flash drive into the USB port on the projector faceplate.

4. Select a backup file and select Download.

5. Select the up arrow to move up through the file directory.

6. In the Name field, enter a name for the backup file.

7. Select Accept.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. If using the touch panel control, insert a USB flash drive into the USB port on the projector faceplate.

3. Select Import Backup.

4. Browse to the location of the file or enter a name for the backup file in the Name field.

5. Select the file and select Open.

6. If the file already exists, in the confirmation dialog select Overwrite.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. Sort the backup files:

To sort the backup files by name, select the Backup File Name heading.

To sort the files by the date they were created, select the Date Created heading.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. Select a backup file and select Delete.

3. To confirm, select Delete.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. Select a backup file and select Restore.

3. Select the settings you want to restore and select Restore.

4. When the restore is complete, select OK.

1. In the left navigation menu, select Service Setup > Backup and Restore.

2. Select Factory Restore.

3. Select the settings you want to restore and select Restore.

4. Select OK.

1. Power on the projector and place it in Standby mode.

2. Upload the required upgrade package using one of the following methods:

Using the touch panel-Upload the required upgrade package to a USB key or navigate to the projector’s ftpuser directory. NTFS-formatted USB drives are not supported for this release.

Using the web user interface (UI)-Upload the required upgrade package to your computer.

3. If using the USB method, insert the USB key into the projector.

4. In the left navigation menu, select Service Setup > System Upgrade.

5. If you uploaded the upgrade package to your computer, select + New Upgrade File.

6. Select the upgrade package file from the list.

7. Select Open.

8. In the right pane, navigate to the upgrade file and select Upgrade.

9. To begin the upgrade, select Upgrade in the confirmation dialog. The projector restarts automatically when the upgrade is complete.

1. In the left navigation menu, select Diagnostics > System Logs/Interrogator.

2. In the From list, select a start date for the logs.

3. In the To list, select an end date for the logs.

4. Select Search Logs.

5. To sort log files by type, message, or date, select a column heading.

1. If using the touch panel control, insert a USB flash drive into the USB port on the projector faceplate.

2. In the left navigation menu, select Diagnostics > System Logs/Interrogator.

3. Select Run Interrogator.

4. In the confirmation dialog, select Interrogate. By default, the interrogator excludes files such as Warp files, LOS data, and older sensor files/core snapshots to limit the log file size.

5. If using the web user interface, in the Interrogator dialog, select Download File.

6. If using the touch panel control, browse to the location where you want the interrogator file to be saved.

7. In the Name field, enter a name for the interrogator file.

8. Select Accept.

1. In the left navigation menu, select Laser Settings > Laser Diagnostics.

2. Review the detailed information for the following:

Model

Version

Serial numbers

Power health

Drivers

Temperature

1. If using the touch panel control, insert a USB flash drive into the USB port on the projector faceplate.

2. In the left navigation menu, select About.

3. Select a certificate type.

4. Select Download. If using the web user interface, the certificate automatically downloads to your computer’s Downloads folder.

5. If using the touch panel control, browse to the location where you want to save the certificate.

6. Select Accept.