CHIEF QMP2MM1 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD CHIEF QMP2MM1 (01) PDF MANUAL


PDF Content Summary: INSTALLATION INSTRUCTIONS Music Stand Height Adjust Single Monitor Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description QMP2MM1 QMP2MM1 Installation Instructions

DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® and Centris® are registered trademarks of Milestone AV Technologies. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the QMP2MM1 up to (and including) the display does not exceed 25 lbs (11.3 kg). Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury. WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. DIMENSIONS PIVOT 90 PIVOT 90 1.38 34.9 15.54 394.8 WARNING: Do not use this product outdoors. --SAVE THESE INSTRUCTIONS-- 1.83 46.4 3.94 100.0 2.95

UP 10 DOWN 3.22 81.7 75.0 2.95 75.0 DIMENSIONS: INCHES

2 QMP2MM1 Installation Instructions

LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme Hex-Head Wrench Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale TOOLS REQUIRED FOR INSTALLATION #2 PARTS B (1) [Cart/stand bracket] C (1) [Assembly bracket] H (4) 3/32" (included) 5/32" (included) 3/16" (included) A (1) [Height-adjust assembly] D (4) E (4) F (4) M4x14mmM4x25mm M10x5.3x10

G (2) 10-24 x 1/2" 5/16-18 x 5/8"K (1) L (1) 5/32"M (1)

3/16" J (2)

#10 3/32"

3 QMP2MM1 Installation Instructions

ASSEMBLY The QMP2MM1 is designed to be attached to Chief carts and stands. 1. Slide cart/stand bracket (B) onto cart/stand column (not included), ensuring that cart/stand bracket tab slides into the front of cart/stand column. (See Figure 1) 2. Fasten the bracket to the cart/stand using four 5/16-18 x 5/8" button head cap screws (H). (See Figure 1) 2 (H) x 4 IMPORTANT ! : If the display being installed has a recessed mounting surface, the display must be assembled to the mount prior to mount installation. See Display Installation section before proceeding. 4. Insert top of height-adjust assembly (A) over lip on top of assembly bracket (C). (See Figure 3) (A) 4

(B) Cart/stand column 1 (C)

(not included) Figure 1 Figure 3 5. Swing height-adjust assembly (A) down flush against assembly bracket (C). (See Figure 4) 3. Attach assembly bracket (C) to cart/stand bracket (B) using two 10-24 x 1/2" button head cap screws (G) and two #10 flat washers (J) through the top two holes in the assembly bracket. (See Figure 2) (B) (C) 3 (G) x 2 (C) 5 (A)

(J) x 2 Figure 2 Figure 4

4 Installation Instructions QMP2MM1

6. Tighten set screw using 5/32" hex key (L). (See Figure 5) CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure set screw engages back side of assembly bracket on cart/stand column. (See Figure 5) (A) (C) (for flush mounting holes) quick release faceplate 3 Figure 7 (D) x 4

Cart/stand column Figure 5 DISPLAY INSTALLATION Display Installation 1. Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount. (See Figure 6) For recessed mounting hole installation: • Place four spacers (F) on top of mounting holes on back of display. (See Figure 8) • Using Phillips screwdriver, carefully install four M4x25mm screws (E) through corresponding holes on faceplate, spacers (F) and into the mounting holes on the display. (See Figure 8) (for recessed mounting holes) quick release faceplate 1 1 quick release lever Figure 6 2. Carefully place display face down on protective surface. 3. Connect faceplate to display For flush mounting hole installation: • Using Phillips screwdriver, carefully install four M4x14mm screws (D) through corresponding holes on faceplate and into the mounting holes on the display. (See Figure 7) 3 (E) x 4 (F) x 4 Figure 8

5 QMP2MM1 Installation Instructions

4. Position display with faceplate attached above mount. (See Figure 9) 5. Slide faceplate onto mounting head until quick release tab clicks into place. (See Figure 9) 5 Figure 9 Adjustments Pitch Adjustment (non-array models) 1. Adjust pitch to desired tilt position. (See Figure ) 2. Adjust pitch tension screw to change the adjustment tension. (See Figure ) Pivot Adjustment (non-array models) 3. Adjust pivot position as desired. (See Figure ) 4. Use 3/16” hex key (M) to adjust pivot point tension screws to change pivot adjustment tension. (See Figure ) Rotational tension 5 Rotational Adjustment NOTE: (Optional) Rotational adjustment may be locked by installing rotational locking screw (L) into back of faceplate. (See Figure 11) (L) Figure 11 5. The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure ) 6. Use 3/16” hex key (M) to adjust rotational adjustment screw to adjust rotational tension. (See Figure ) Lift Arm Tension Adjustment 1. Use 3/16” hex key (M) to adjust lift arm tension adjustment screw. (See Figure 12) 1 Reduce tension (lighter display) Increase tension (heavier display)

1 pitch tension 3 Figure 10 pivot point tension Do NOT over-tension adjustment tension screw. Figure 12

6 Installation Instructions QMP2MM1

NOTE: Tension may also be adjusted with upper tension adjustment screw inside cable management cover and 1/8” hex key (N). (See Figure 13) Reduce tension (lighter display) Increase tension (heavier display) Do NOT over-tension adjustment tension screw. Figure 13 Display Removal WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove Cable Management 1. Press insides of cable management covers at both ends to unhinge tabs on either end of cable management cover on upper arm. (See Figure 15) 2. Lift cable management cover up until tabs are unhinged and cover is in the “open” position. (See Figure 15) 1 2 cable management cover tabs Figure 15

display unless the display is in the upright position! (See Figure 14) 1. Make sure display is in the upright position. 2. Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount. (See Figure 14) 3 2 4 cable (typical)3

2 quick release tab Figure 14 Figure 16 3. Route cables through cable management channels. (See Figure 16) IMPORTANT ! : Be sure to leave enough slack in the cables near display and arm joint to allow for full arm articulation! 4. Close cable management covers on monitor arm. (See Figure 16)

7 QMP2MM1 Installation Instructions USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852

Chief, a products division of Milestone AV Technologies 8800-002728 Rev00 ⁄2015 Milestone AV Technologies chiefmfg.com 05/15 F +31 (0) 495 580 845 Asia Pacific A Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply