CASIO 5460 (02) PDF MANUAL

The watch indicators show the following:

① Hour and minute hands: Indicate the current time in your Home City zone.

② Day: Indicates the day in your Home City zone.

③ A/P marks: When configuring the Dual Time setting, the second hand will point to “A” for a.m. times, and to “P” for p.m. times.

④ Small hour and minute hands: Indicate the current time in your World Time (Dual Time) City.

⑤ Second hand: Indicates the current second in your Home City zone.

⑥ C mark: When the watch is connected with a phone, the second hand points to “C”.

⑦ F mark: When the watch is connected with a phone that supports a phone finder function, the second hand will point to “F”.

⑧ R mark: When the watch is standing by for connection with a phone, the second hand points to “R”.

⑨ Small 24-hour hand (Module 5460 only): Indicates the current time in your World Time (Dual Time) City.

Pulling Out and Pushing In the Crown:

Before performing a crown operation, you need to pull it out to the first or second click as shown in the figures. Do not pull the crown with too much force.

Important!

• To prevent loss of water resistance and/or damage due to impact, be sure to push the crown in to its normal position after you are finished using it.

• When pushing the crown back in, take care not to apply too much force.

Fast Forward/Fast Reverse:

After pulling out the crown, rotating it quickly in succession in either direction will cause the hands to move forward or back at high speed. While the hands are moving forward at high speed, quickly rotating the crown in succession again will increase the speed even further.

Stopping Fast Forward/Fast Reverse:

Rotate the crown in the direction opposite that of the ongoing operation or press any button.

Note:

• If you do not perform any operation for about three minutes after pulling out the crown, crown operations will automatically become disabled. If that happens, push the crown back in and then pull it out again.

The day indication changes each day between 10:00 p.m. to 2:00 a.m. the next day.

The day may not be indicated correctly while the watch’s crown is pulled out.

This watch runs on power supplied from a rechargeable (secondary) battery that is charged by a solar panel. The solar panel is integrated into the face of the watch, and power is generated whenever the face is exposed to light.

Charging the Watch:

When you are not wearing the watch, put it in a location where it is exposed to bright light.

While you are wearing the watch, make sure that its face (solar panel) is not blocked from the light by the sleeve of your clothing. Power generation efficiency is reduced even when the face of the watch is blocked only partially.

Important!

• Depending on light intensity and local conditions, the watch may become hot to the touch when exposed to light for charging. Take care to avoid burn injury after charging. Also, avoid charging the watch under high-temperature conditions like the ones described below:

– On the dashboard of a vehicle parked in the sun

– Near an incandescent light bulb or other source of heat

– Under direct sunlight or in other hot areas for long periods

The charge level is indicated by watch hand movement. Functions become disabled as battery power goes low.

If the battery is low, the second hand jumps at two-second intervals.

If the battery is dead, all hands and the day indicator are stopped.

Important!

• Should battery go low or go dead, expose the face (solar panel) to light as soon as possible.

Note:

• Exposing the watch face to light after the battery goes dead will cause the second hand to revolve counterclockwise until it stops at second 57. This indicates charging has started.

Required Charging Time for 1-day Use:

Time Required to Achieve Next Charge Level:

Light Intensity:

① Sunny day, outdoors (50,000 lux)

② Sunny day, near a window (10,000 lux)

③ Overcast day, near a window (5,000 lux)

④ Indoor fluorescent lighting (500 lux)

Charge Level 1: Time from dead battery until hand movement starts

Charge Level 2: Time from hand movement starts until a full charge

Actual charging time depends on the local charging environment.

Power Saving:

Leaving the watch in a dark location for approximately one week will cause movement all of the watch’s hands to stop in order to save power. Only the day indicator is operational.

Recovering from Power Saving Operation:

Press any button or place the watch in a well-lit area to recover from power saving.

To use the watch with a phone, first install the “CASIO WATCH+” app on the phone. The PDF provides specific links for iOS and Android users, but as per instructions, these links are not included here.

Enable the phone’s Bluetooth.

iPhone Users:

1. On the Home Screen, tap “Settings” → “Bluetooth”.

2. Enable “Bluetooth”.

3. Tap “Settings” to return to the “Settings” screen.

4. Tap in the following sequence: “Privacy” → “Bluetooth Sharing”.

5. Enable “CASIO WATCH+”.

Android Users:

Enable Bluetooth.

If you are presented with a choice between “Bluetooth” and “Bluetooth Smart”, select “Bluetooth Smart”.

Note: For details about setting procedures, see your phone documentation.

Before you can use the watch in combination with a phone, you first need to pair them. Once the watch is paired with a phone, you normally do not need to pair them again.

1. Move the phone to be paired with close to (within one meter of) the watch.

2. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

3. On the phone, tap “SHEEN”.

4. Perform operations as instructed by the app.

• The model name is stamped on the back cover of the watch.

• If a pairing prompt message appears, perform the operation shown on the phone screen.

• When pairing starts, the second hand will move to 12 o’clock or to the “R” mark. When pairing is complete, the second hand will move to “C”.

Note: This function is available only while CASIO WATCH+ is running on the phone.

The watch can be set to adjust its time setting automatically each day in accordance with the phone time.

Using Auto Adjust:

Your watch adjusts its time setting four times a day. It performs the adjustment operation automatically as you go about your daily life, without any operation required by you.

Important!

• The watch may not be able to perform auto time setting adjustment under the conditions described below:

– While it is too far away from its paired phone

– While communication is not possible due to radio interference, etc.

– While the phone is updating its system

Note:

• If there is a World Time City specified with CASIO WATCH+, its time will also be adjusted automatically.

• The watch will connect with the phone and perform auto time adjustment at around 5:00 a.m., 11:00 a.m., 5:00 p.m. and 11:00 p.m. The connection is automatically terminated after auto time adjustment is complete.

The watch will adjust its time setting to that of the phone immediately after they are connected with each other. Whenever you want to adjust the watch’s time setting perform the procedure below to connect with a phone.

If CASIO WATCH+ is already running, you can skip step 1. In this case, advance to step 2 of this procedure.

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. On the watch, press (B).

This causes the second hand to move to “R”. The second hand will move to “C” when a connection is established between the watch and phone, and the time setting of the watch will adjust to the phone’s time setting.

The connection is terminated automatically after time adjustment is complete.

Specifying a World Time City with CASIO WATCH+ causes the city’s time to be indicated by the small hour and minute hands. Watch settings can be configured for auto summer time switching for the World Time City.

Selecting a World Time City:

1. On the phone, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap “World Time”.

4. On the phone, specify a World Time City by inputting a city name or by tapping its location on the on-screen map.

5. On the phone, perform the operation shown on the phone screen. The World Time setting will be reflected on the watch.

The small hour and minute hands of the watch will indicate the current time in the specified World Time City. (The display varies slightly if your watch has a small 24-hour hand).

Note: CASIO WATCH+ World Time lets you select from among approximately 300 cities as the World Time City.

1. On the phone, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap “World Time”.

4. On the phone, specify a World Time City by inputting a city name or by tapping its location on the on-screen map. If your currently specified World Time City observes summer time, the summer time period will appear on the display.

5. On the phone, select the summer time switching method you want to use:

• “Auto”: The watch switches between standard time and summer time automatically.

• “OFF”: The watch always indicates standard time.

• “ON”: The watch always indicates summer time.

6. On the phone, perform the operation shown on the phone screen.

Note:

• When “Auto” is selected for standard/summer time switching, the watch will switch between standard time and summer time automatically. You do not need to change the time setting manually for changes between summer time and standard time. Even if you are in an area that does not observe summer time, you can leave the watch’s summertime setting as “Auto”.

• Changing the time setting manually with a watch operation will cancel auto standard time/summer time switching.

• A CASIO WATCH+ screen shows information about summer time periods.

1. On the phone, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap the swap icon (often represented by arrows).

4. Perform the operation shown on the phone screen to swap your Home Time with your World Time.

For example, if your Home City is Tokyo and the World Time City is New York, they will be swapped.

Note: Auto time adjustment is not performed for 24 hours after swapping of the Home Time and World Time.

If the hands are out of alignment even though auto time adjustment is being performed, use CASIO WATCH+ to adjust them.

1. On the phone, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap in the following sequence: Menu icon (often three lines or dots) → “Watch settings”.

4. On the phone, tap “Adjusting the home positions”.

5. Perform the operation shown on the phone screen.

Note: The movement of some hands are linked with other hands. When correcting the alignment of such a hand, you will have to correct the alignment of the linked hand(s) at the same time.

You can use phone finder to trigger a tone on the phone to make it easy to find. The tone is forced to sound even if the phone is in manner mode.

Important!

• Do not use this function in areas where phone call tones are restricted.

• The tone sounds at a high volume. Do not use this function when listening to phone output over earphones.

1. If the watch is connected with a phone, press (B) on the watch to terminate the connection. (The second hand moves from “C” to its normal timekeeping position).

2. On the watch, hold down the (B) button for about three seconds until the second hand points to “F”.

This starts the phone finder operation. The second hand will move to “C” when a connection is established between the watch and phone, and then the phone’s ringtone will sound.

It will take a few seconds before the phone tone sounds.

3. Press any button on the watch to stop the tone.

You can press any watch button to stop the phone tone only during the first 30 seconds after it starts to sound.

You can use CASIO WATCH+ to specify the amount of time until the Bluetooth connection is automatically terminated, and to configure other settings.

1. On the phone, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap in the following sequence: Menu icon → “Watch settings”.

4. On the phone, select the setting you want to change and then perform the operation shown on the phone screen.

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. On the phone, tap in the following sequence: Menu icon → “Watch settings”.

4. On the phone, tap “Summer time setting for home time”.

5. On the phone, select the summer time switching method you want to use:

• “Auto”: The watch switches between standard time and summer time automatically.

• “OFF”: The watch always indicates standard time.

• “ON”: The watch always indicates summer time.

6. Perform the operation shown on the phone screen.

Use the procedure below to check the current charge level with CASIO WATCH+.

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

3. Use CASIO WATCH+ to check the charge level (the specific location in the app may vary, but it’s typically within watch status or settings).

Important! If you have problems establishing a connection, it could mean that CASIO WATCH+ is not running on the phone. On the phone’s home screen, tap the “CASIO WATCH+” icon. After the app starts up, hold down the watch’s (B) button for about 1.5 seconds.

Note:

• The connection will be terminated if you do not perform any operation on the watch or phone for a fixed amount of time. To specify the connection limit time, perform the following operation with CASIO WATCH+: “Watch settings”→”Set the time for connecting to this app”. Next, select a setting of 3 minutes, 5 minutes, or 10 minutes.

• While the watch is connected with the phone, the second hand makes one revolution with each passing minute.

This section explains how to establish a Bluetooth connection between a phone that is paired with the watch. When a connection is established, the watch will adjust its time setting to that of the phone.

If the watch is not paired with the phone you want to connect with, perform the procedure under “Pairing the watch with a phone” to pair them.

1. Move the phone close to (within one meter of) the watch.

2. While the second hand is not pointing to “C”, hold down the (B) button on the watch for about 1.5 seconds.

• The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

• The second hand will move to “C” when a connection is established between the watch and phone.

Pressing (B) on the watch terminates the Bluetooth connection and returns the second hand to its normal operation.

Whenever you are in a hospital, on an aircraft, or in any other location where auto time adjustment may cause problems, you can perform the procedure below to disable it. Perform the same procedure again to re-enable auto time adjustment.

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. On the watch, hold down the (B) button for about 1.5 seconds.

The second hand will move to “C” when a connection is established between the watch and phone.

The second hand will move to “R”. Keep (B) depressed until the second hand starts moving again and then stop at “R”.

3. On the phone, tap in the following sequence: Menu icon → “Watch settings”.

4. On the phone, tap “Time adjustment” (or a similar option to toggle auto adjustment).

5. Perform the operation shown on the phone screen to disable/enable auto time adjustment.

1. If the watch is connected with a phone, press (B) on the watch to terminate the connection.

2. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

3. On the phone, tap the CASIO WATCH+ Menu icon (often three lines or dots).

4. In the “Previously registered watch” list, tap the watch you want to unpair.

5. Tap “Delete pairing registration”.

6. Tap “Delete”.

This unpairs the watch from the phone.

Note for re-pairing issues after unpairing:

If you are unable to re-pair the watch with a phone after unpairing them, use the procedure below to delete pairing information from the watch and then perform the pairing operation again.

① Pull out the crown on the watch to the second click.

② Hold down (B) on the watch for about five seconds. The second hand will move to 12 o’clock. Keep (B) depressed until the second hand moves to 12 o’clock. This deletes pairing information from the watch.

③ Push the crown back in.

You need to perform the operation below whenever you want to establish a Bluetooth connection with a phone that is different from the one you are currently connected with.

1. Unpair the watch from your current (old) phone. (Follow the “How do I unpair the watch from a phone?” procedure).

2. Pair the watch with your new phone. (Follow the “How do I pair the watch with a phone?” procedure).

You should perform the steps below before pairing a different watch with the phone, such as after you buy a new watch.

Pairing the Watch with a Phone:

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. In the upper left corner of the screen (in CASIO WATCH+), tap the menu icon.

3. On the list that appears, tap the brand of the watch you want to connect with.

4. Perform operations as instructed by the app.

• The model name is stamped on the back cover of the watch.

Connecting with a Watch that is Already Paired (if you are switching between watches already paired with the phone):

1. On the phone’s Home Screen, tap the “CASIO WATCH+” icon.

2. Swipe the screen to scroll through available watches and display the one you want to connect with.

3. Perform watch operations in accordance with the instructions that appear on the phone screen.

Important! A phone can be connected with only one watch at a time. To connect to another watch, you need to terminate the current connection.

While the watch is connected to a phone, it will automatically adjust its day and time settings to those of the phone. If the watch is not connected to a phone, use the procedure below to adjust its day and time settings.

1. Pull out the crown to the second click. This causes the second hand to move to 12 o’clock, and enables the minute setting operation.

2. Rotate the crown to change the minute setting. The Dual Time setting is also adjusted in accordance with the current time setting.

3. Press (A). This enables the time and day setting operation.

4. Rotate the crown to change the time and day settings. Check the a.m./p.m. setting whenever there is a change to another day.

5. Press (A). This enables the month setting operation.

6. Rotate the crown to change the month setting.

7. Press (A). This enables the year 10’s digit setting operation.

8. Rotate the crown to change the year 10’s digit.

9. Press (A). This enables the year one’s digit setting operation.

10. Rotate the crown to change the year one’s digit.

11. On a time signal at the top of a minute, push the crown back in.

Dual Time lets you keep track of the current time in another time zone in addition to your Home City zone.

1. Pull out the crown to the first click.

2. Rotate the crown to change the Dual Time setting.

• You can set the Dual Time in 15-minute increments.

• If your watch does not have a small 24-hour hand, you can find out whether the Dual Time is showing an a.m. or p.m. time by checking the position of the second hand (pointing towards PM for p.m., AM for a.m.).

• If your watch has a small 24-hour hand, you can find out whether the Dual Time is showing an a.m. or p.m. time by checking the position of the small 24-hour hand.

3. Push the crown back in.

You can swap your Home City with the Dual Time by holding down (A) on the watch for about three seconds.

Note: If the current times were set manually on the watch (not automatically by the phone), the dates will not be swapped. Only the times are swapped.

Strong magnetism or impact can cause the time indicated by the hands and the day indicator to go out of alignment. If this happens, adjust hand and day indicator alignment.

1. Pull out the crown to the first click.

2. Hold down (A) for about five seconds. This enables adjustment of second and minute hand alignment.

3. Rotate the crown to align the second and minute hands with 12 o’clock. The minute hand of this watch moves in conjunction with second hand movement.

4. Press (A). This enables adjustment of hour hand alignment.

• If the hand position is more than three hours out of alignment, you will not be able to use step 5 to correct it. If this is the case, skip step 5 and go to step 6.

5. Rotate the crown to align the hour hand with 12 o’clock.

6. Press (A).

• If your watch does not have a small 24-hour hand, this enables adjustment of the small hour and minute hands (Dual Time hands).

• If your watch has a small 24-hour hand, this enables adjustment of the small hour and minute hands, and the small 24-hour hand.

7. Rotate the crown to align the small hour and minute hands with 12 o’clock. If your watch has a small 24-hour hand, also align it with 12 o’clock (24).

8. Hold down (A) for about two seconds. This enables adjustment of day indicator alignment. If the hour hand was misaligned by more than three hours in step 4, you can also correct hour hand alignment here.

9. Rotate the crown to center the day indicator between “1” and “31”, and the hour hand with 12 o’clock. Note that date indicator and hour hand movement are linked with each other.

10. Push the crown back in.

Use the procedure below to easily change day and time settings of the watch to a destination location.

Before Boarding:

1. Configure the World Time (Dual Time) to the current time at your destination. (Refer to “Configuring Dual Time Settings” or “Configuring World Time Settings using CASIO WATCH+”).

2. Disable auto time adjustment. (Refer to “How do I use the watch in a medical facility or aircraft?”).

After Arriving:

1. Swap the origin time zone time with the destination time zone time. (Refer to “Swapping the Home City Time and World Time (Dual Time)” manually or via CASIO WATCH+).

2. Enable auto time adjustment. (Refer to “How do I use the watch in a medical facility or aircraft?”).

Connecting with a Phone to Switch:

After the watch is connected with a phone, summer time switching of Home City time and World Time is performed in accordance with the CASIO WATCH+ setting (Auto/ON/OFF) as described below.

• Auto: After the watch is connected with a phone, summer time is displayed for the current location time or World Time when it is within the summer time period. Otherwise standard time is displayed.

• ON: The watch always displays summer time.

• OFF: The watch always displays standard time.

Auto Summer Time Switching:

When the watch is connected to a phone, it is sent summer time period information for your Home City. If there is a World Time City specified with CASIO WATCH+, information for that city will also be sent. If the CASIO WATCH+ summer time setting is “Auto”, the watch will automatically keep track of the summer time period and perform summer time switching automatically, even if it is not connected with the phone.

• This watch complies with or has received approval under the radio laws of various countries and geographical areas. Using this watch in an area where it does not comply with or has not received approval under applicable radio laws may be a criminal offense.

• Use of this watch inside of aircraft is restricted under the aviation laws of each country. Be sure to follow the instructions of airline personnel.

• When using this watch in combination with a phone, keep the watch and phone close to each other. A range of two meters is recommended as a guideline, but the local environment (walls, furniture, etc.), the structure of a building, and other factors may require a much closer range.

• This watch can be affected by other devices (electrical devices, audio-visual equipment, office equipment, etc.) In particular, it can be affected by operation of a microwave oven. The watch may not be able to communicate normally with a phone if a microwave oven is operating nearby. Conversely, this watch may cause noise in radio reception and the video image of a TV.

• Bluetooth of this watch uses the same frequency band (2.4 GHz) as wireless LAN devices, and use of such devices in close proximity of this watch may result in radio interference, slower communication speeds and noise for the watch and the wireless LAN device, or even communication failure.

The watch is emitting radio waves whenever the second hand is pointing to “C” (Bluetooth connected) or “R” (Bluetooth connection standby). Even if the second hand is not pointing at “C” or “R”, the watch will attempt to connect with a phone four times a day to adjust its time settings.

When in a hospital, on an aircraft, or in any other area where the use of radio waves is not allowed, use CASIO WATCH+ to disable syncing between the watch and phone. For details, see “How do I use the watch in a medical facility or aircraft?”.

Are you using a supported phone model?

Check if the phone model and its operating system are supported by the watch. For information about supported phone models, you would typically visit the CASIO support page (not included here per instructions).

Is CASIO WATCH+ installed on your phone?

The CASIO WATCH+ needs to be installed in order to connect with the watch. (Refer to “How do I install the CASIO WATCH+ application?”).

Are your phone’s Bluetooth settings configured correctly?

Configure the phone’s Bluetooth settings. For details about setting procedures, see your phone documentation.

iPhone Users:

• “Settings” → “Bluetooth” → On

• “Settings” → “Privacy” → “Bluetooth Sharing” → “CASIO WATCH+” → On

Android Users:

• Enable Bluetooth.

Other than the above:

Some phones need to have BT Smart disabled to use CASIO WATCH+. For details about setting procedures, see your phone documentation.

On the Home Screen, tap: “Menu” → “Settings” → “Bluetooth” → “Menu” → “BT Smart settings” → “Disable”.

To connect with a newly purchased phone, you will need to perform the pairing operation again with the new phone. Use CASIO WATCH+ to delete the pairing information from your current (old) phone, and then pair the watch with the new phone. (Refer to “What do I do if I purchase another phone?”).

Is CASIO WATCH+ running on your phone?

Check if CASIO WATCH+ is running on the phone. On the phone’s Home Screen, tap the CASIO WATCH+ icon. Then on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

Have you tried turning your phone off and then back on again?

Turn the phone off and then back on, and then tap the CASIO WATCH+ icon. Next, on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

Connection with the watch is not possible while the phone is in the Airplane Mode. After exiting the phone’s Airplane Mode, go to its Home Screen and tap the “CASIO WATCH+” icon. Then on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

On the phone, disable and then re-enable Bluetooth, and then go to the Home Screen and tap the “CASIO WATCH+” icon. Next, on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

Turn on the phone and tap the CASIO WATCH+ icon. Then on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

Have you tried turning your phone off and then back on again?

Turn the phone off and then back on, and then tap the CASIO WATCH+ icon. Next, on the watch, hold down the CONNECT button (B) for about 1.5 seconds.

Has the watch been re-paired with the phone?

After unpairing the watch and phone, re-pair them again. (Refer to “If you purchase another phone” and “Unpairing” sections for details).

If you are unable to establish a connection…

Delete the pairing information from the watch, and then re-pair the watch and phone. (Refer to the note under “How do I unpair the watch from a phone?” for deleting pairing info from the watch, and the “Unpairing” section).

Clear pairing information from the watch you are currently using (see note under “How do I unpair the watch from a phone?”), and then pair with another phone (see “How do I pair the watch with a phone?”). (Also refer to “If you purchase another phone”).

Are the phone and watch disconnected?

Phone Finder does not work during Bluetooth connection. Press (B) on the watch to terminate the connection first if it is connected.

Is CASIO WATCH+ running on your phone?

Phone Finder will not work unless CASIO WATCH+ is running. On the Home Screen, tap the CASIO WATCH+ icon.

Other than the above:

If the phone does not respond after a few seconds, it could mean that the phone is located too far from the watch. Change to a different location and try again.

The phone will emit a tone when a connection is established with the watch, which takes a few seconds.

Since communication is performed using radio waves, the watch may not be able to find the phone even if it is within two meters. Certain environments may make the allowable communication range very short.

The watch will connect with the phone and perform auto time adjustment at around 5:00 a.m., 11:00 a.m., 5:00 p.m. and 11:00 p.m. The connection is automatically terminated after auto time adjustment is complete.

Is auto time adjustment not being performed according to its normal schedule?

Note that auto time adjustment is not performed for 24 hours after swapping of the Home Time and World Time, or after the time setting is adjusted manually on the watch. Auto time adjustment will resume 24 hours after either of the above operations is performed.

Is auto time adjustment enabled?

Auto time adjustment will not be performed at the scheduled times unless it is enabled. Establish a connection between the watch and phone, and then use CASIO WATCH+ to enable auto time adjustment. (Refer to “How do I use the watch in a medical facility or aircraft?” for enabling/disabling auto time adjustment).

The phone’s time setting may not be correct.

① Correct the phone’s time setting.

iPhone Users:

• “Settings” → “Privacy” → Turn on “Location Services” → “System Services” → Turn on “Setting Time Zone”.

Android Users:

• Refer to your phone’s user documentation.

② Establish a connection between the watch and phone, and correct the time setting. (Refer to “How do I trigger an immediate time adjustment?”).

The summer time start date and time, end date and time, or other rules were changed by authorities. You may need to update settings via CASIO WATCH+ or manually adjust if not connected.

Button operations are disabled while high-speed hand movement is in progress after a watch setting is changed, etc. Wait until the hands stop moving before performing button operations.

Battery power is low. Keep the watch exposed to light until it recharges sufficiently. (Refer to “How do I charge the watch?”).

The battery is dead. Keep the watch exposed to light until the battery recharges sufficiently. (Refer to “How do I charge the watch?”).

This is due to one of the reasons below, and does not indicate malfunction. Simply wait until normal hand movement resumes.

• The watch is recovering from a power saving state. (Refer to “What is Power Saving and how do I recover from it?”).

• Watch is connected with a phone to adjust its time setting. (Refer to “How does Auto Time Adjustment work?” or “How do I trigger an immediate time adjustment?”).

The watch is in the charge recovery mode. Wait until the recovery process is complete (for about 15 minutes). The watch will recover more quickly if you place it in a brightly lit location.

Strong magnetism or impact may cause the hands of the watch to go out of alignment. Use CASIO WATCH+ to correct hand alignment (Refer to “How do I correct hand alignment using CASIO WATCH+?”) or perform manual hand alignment correction (Refer to “How do I correct hand and day indicator alignment manually?”).

The day is in the process of changing. For information about how the day changes, see the section “How does the day indicator change?”.

Leaving the crown pulled out for more than three minutes without performing any operation will automatically disable crown operation. Push the crown back in to its normal position and then pull it out again. (Refer to “How do I use the crown?”).

Crown operation is disabled while high-speed hand movement is in progress after a watch setting is changed, etc. Wait until the hands stop moving before performing crown operations.

The watch stops operating whenever the battery goes dead. Keep the watch exposed to light until it recharges sufficiently. (Refer to “How do I charge the watch?”).