CANYON CNS-TWS10 (01) PDF Document

The specifications for the CANYON CNS-TWS10 True Wireless Stereo (TWS) earbuds include:

The CANYON CNS-TWS10 earbuds can be turned on in two ways:

1. Take the earbuds out of the charging case. They will turn on automatically.

2. Long press the touch area on the earbuds for 2 seconds to turn them on manually.

The CANYON CNS-TWS10 earbuds can be turned off in two ways:

1. Place the earbuds into the charging case. They will turn off automatically.

2. Long press the touch area on the earbuds for 5 seconds to turn them off manually.

To pair the CANYON CNS-TWS10 earbuds:

Step 1. Take the earbuds out of the charging case. They will enter pairing mode automatically, and the indicator light will flash.

Step 2. Enable Bluetooth on your device (phone, tablet, etc.).

Step 3. Select “CANYON CNS-TWS10” from the list of available devices in your device’s Bluetooth settings.

Step 4. Once connected, the indicator light will stop flashing.

Note: If pairing is unsuccessful, place the earbuds back into the case, close the lid, and repeat the steps.

To adjust the volume on the CANYON CNS-TWS10 earbuds:

1. To increase the volume, quickly tap the touch area on the right earbud twice.

2. To decrease the volume, quickly tap the touch area on the left earbud twice.

To skip tracks using the touch controls on the CANYON CNS-TWS10 earbuds:

1. To skip to the next track, quickly tap the touch area on the right earbud three times.

2. To go to the previous track, quickly tap the touch area on the left earbud three times.

To manage phone calls with the CANYON CNS-TWS10 earbuds:

1. To answer an incoming call, quickly tap the touch area on either earbud twice.

2. To end an ongoing call, quickly tap the touch area on either earbud twice.

3. To reject an incoming call, long press the touch area on either earbud for 2 seconds.

To activate the voice assistant (Siri, Google Assistant, etc.) on your connected device using the CANYON CNS-TWS10 earbuds, quickly tap the touch area on either earbud three times.

If the CANYON CNS-TWS10 earbuds fail to turn on, consider the following troubleshooting steps:

1. Check the battery level of the earbuds and the charging case. If they are low, place them on charge.

2. If the earbuds are charged, try manually turning them on by long pressing the touch area for 2 seconds.

3. If they still do not turn on, place them in the charging case for a short period and then try again.

If the CANYON CNS-TWS10 earbuds do not connect or pair with your device, follow these troubleshooting steps:

1. Ensure Bluetooth is enabled on your device and that the earbuds are charged and within range (10m).

2. Make sure the earbuds are not already connected to another device.

3. Place both earbuds back into the charging case, close the lid for a few seconds, take them out again, and attempt pairing.

4. If the problem persists, reset the earbuds to factory settings (refer to the manual for reset instructions if available, though a general step is placing them in the case and closing the lid often initiates a state change).

5. Check if “CANYON CNS-TWS10” is listed in the device’s Bluetooth settings and try to remove/forget the device and then pair again.

If you experience sound distortion or low volume from the CANYON CNS-TWS10 earbuds:

1. Check the volume settings on both the earbuds (using touch controls) and the connected source device.

2. Ensure the earbuds are clean and that the speaker mesh is not blocked by debris or earwax.

3. Confirm that the connected device is not streaming audio at a low quality setting.

4. Try pairing the earbuds with a different device to determine if the issue lies with the source device or the earbuds.

To charge the CANYON CNS-TWS10:

1. To charge the earbuds, place them inside the charging case. The case will automatically charge the earbuds.

2. To charge the charging case itself, connect a USB Type-C cable to the charging port on the case and connect the other end to a USB power source.

3. The charging time for the earbuds is approximately 1.5 hours, and for the case, it is approximately 2 hours.

The charging status for the CANYON CNS-TWS10 is indicated by the LED light:

1. Charging: The LED light will be on (usually red or white, depending on the model’s specific indicator color, but the document shows an indicator light is present).

2. Fully Charged: The LED light will turn off or change color to indicate a full charge.

The working distance for the CANYON CNS-TWS10 earbuds using Bluetooth is up to 10 meters.