CAMDEN OE-ED2000 (01) PDF MANUAL

The package includes the following items:

1- 4 PIN power connector

4- Wire nuts

5- M5 x 12mm screws

2- #10 x 1 1/4″ wood screws

2- #10-32 x 1/2″ screws

2- Mounting brackets

2- Spacers

Voltage	12/24V AC/DC
Current Draw	300mA@12V DC 150mA@24V DC
Static Strength	1,000 Lbs.
Dynamic Strength	50 Ft-Lbs.
Endurance	700,000 Cycles (Factory Tested) 250,000 Cycles (UL Verified)
Mode	Field Selectable Fail Safe/Fail Secure
Mech. Adjustment	Strike Body/Faceplate
Operation	AC-Buzz DC-Silent
Duty	Continuous
Dimensions (Body)	3 3/8″ H x 1 7/8″ W x 1 7/32″ D (86mm x 47mm x 31mm)

– Line Security = Level I

– Attack Level = Level I

– Endurance Level = Level IV

– Standby Power = Level I

1. Prepare the door jamb as per the appropriate drawing.

2. Install mounting brackets to jamb using M5x12 screws and pressed metal nuts. Do not tighten.

3. Spacers are used to assure flush final assembly of faceplate into jamb. Add one of more spacers between jamb and mounting bracket when face plate extends beyond the jamb. When the faceplate sits inside the jamb, spacers must be added between the mounting bracket & the lip bracket. Make sure clearance hole in spacer aligns with hole in mounting bracket.

4. Connect wires coming from the low voltage side of the transformer to wires (black) from strike.

5. Install electric strike jamb by attaching with # 10-32 screws and lockwashers.

6. Secure M5x12 screws holding mounting brackets to jamb.

Note: The products are intended to be installed in accordance with the installation wiring diagram, mechanical assembly drawings provided with each product, the local authority having jurisdiction (AHJ) and the National Electric Code, NFPA 70. When installed in fail secure mode, the local authority shall be consulted with regard to the use of possible panic hardware to allow emergency exit from the secure area.

The electric door strike shall be installed in such a way and in such a location so as to not impair the operation of an emergency exit device or panic hardware mounted on the door.

A varistor is provided to protect/prevent the strike from spikes. Connect the varistor between the input wires.

Power Connections:

12VDC

Red/Black: +12V

Blue/Green: Ground

24VDC

Red: +24V

Black/Blue: –

Green: Ground

For cut wires:

12V

(+12V) Varistor: Red

(-): Black, Blue, Green

24V

(+24V) Varistor: Red

(-): Black, Blue, Green

Note: For UL 294 / UL 1034 compliance the door strikes are to be powered via a UL 294/ UL 603 class 2 power limited output from a control panel and or power supply. Furthermore, when powered by AC/DC the units shall use a UL regulated UL 294/ UL 603 power limited class 2 output rated 12/24V with AC on indicator.

To modify the mode from fail-safe to fail-secure or vice versa, follow these steps:

(1) Loosen the Set Screw.

(2) Rotate the Mode Selector to the desired setting. (FL – Fail-Secure, FS – Fail-Safe). The Set Screw will slide to its new position as the Mode Selector is rotated.

(3) Tighten the Set screw.

Note: FS = Fail Safe, FL = Fail Lock (Fail Secure)

The following faceplates are available:

OE-EFS1 – ANSI SQUARE

OE-EFS2 – ANSI ROUND

OE-EFS3 – WOOD DOOR

OE-EFS4 – HOLLOW METAL DOOR